iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3666-05

(Specification)

Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials

Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials

SCOPE
1.1 This specification covers the minimum requirements for field and laboratory personnel, for establishing and maintaining a quality system, and establishes minimum qualifications for agencies engaged in the testing and inspection of bituminous paving materials.
1.2 Criteria are provided for evaluating the capability of an agency to properly perform designated tests on bituminous paving materials, and for establishing guidelines pertaining to an agency's organization, personnel, facilities, and quality system. This specification may be supplemented by more specific criteria, such as that in Specification E329, and requirements for particular projects.
1.3 This specification can be used as a basis to evaluate testing or inspection agencies, or both, and is intended for use for the qualifying or accrediting, or both, of testing or inspection agencies, public or private, engaged in the testing and inspection of bituminous paving materials.
1.4 Accreditian is required to comply with this standard (See 8.1.5).
1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Jan-2005
ICS
93.080.20 - Road construction materials
Technical Committee
D04 - Road and Paving Materials
Drafting Committee
D04.95 - Quality Control, Inspection and Testing Agencies
Current Stage
Ref Project

Relations

Replaces
ASTM D3666-04 - Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
Effective Date
01-Feb-2005
Replaced By
ASTM D3666-05a - Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
Effective Date
01-Jun-2005
Referred By
ASTM D6857/D6857M-18 - Standard Test Method for Maximum Specific Gravity and Density of Asphalt Mixtures Using Automatic Vacuum Sealing Method
Effective Date
01-Feb-2005
Referred By
ASTM D6297-20 - Standard Specification for Asphaltic Plug Joints for Bridges
Effective Date
01-Feb-2005
Referred By
ASTM D6936-17 - Standard Test Method for Determining Demulsibility of Emulsified Asphalt
Effective Date
01-Feb-2005
Referred By
ASTM D7000-19a - Standard Test Method for Sweep Test of Emulsified Asphalt Surface Treatment Samples
Effective Date
01-Feb-2005
Referred By
ASTM D2027/D2027M-19 - Standard Specification for Cutback Asphalt (Medium-Curing Type)
Effective Date
01-Feb-2005
Referred By
ASTM D6935-22 - Standard Test Method for Determining Cement Mixing of Emulsified Asphalt
Effective Date
01-Feb-2005
Referred By
ASTM D70/D70M-21 - Standard Test Method for Specific Gravity and Density of Semi-Solid Asphalt Binder (Pycnometer Method)
Effective Date
01-Feb-2005
Referred By
ASTM D8467-22 - Standard Test Method for Determination of Emulsified Asphalt Residue By Quick Boil
Effective Date
01-Feb-2005
Referred By
ASTM D139-16 - Standard Test Method for Float Test for Bituminous Materials
Effective Date
01-Feb-2005
Referred By
ASTM D6372-23 - Standard Practice for Design, Testing, and Construction of Microsurfacing
Effective Date
01-Feb-2005
Referred By
ASTM D4867/D4867M-22 - Standard Test Method for Effect of Moisture on Asphalt Mixtures
Effective Date
01-Feb-2005
Referred By
ASTM D7370/D7370M-14(2021) - Standard Test Method for Determination of Relative Density and Absorption of Fine, Coarse, and Blended Aggregate Using Combined Vacuum Saturation and Rapid Submersion
Effective Date
01-Feb-2005
Referred By
ASTM D7981-20 - Standard Practice for Compaction of Prismatic Asphalt Specimens by Means of the Shear Box Compactor
Effective Date
01-Feb-2005

Buy Standard

ASTM D3666-05 - Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving MaterialsASTM D3666-05 - Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
PreviousNext
Technical specification
ASTM D3666-05 - Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 3666 – 05
Standard Specification for
Minimum Requirements for Agencies Testing and Inspecting
1
Road and Paving Materials
This standard is issued under the fixed designation D 3666; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D5 Test Method for Penetration of Bituminous Materials
D8 Terminology Relating to Materials for Roads and Pave-
1.1 This specification covers the minimum requirements for
ments
fieldandlaboratorypersonnel,forestablishingandmaintaining
D36 Test Method for Softening Point of Bitumen (Ring-
a quality system, and establishes minimum qualifications for
and-Ball Apparatus)
agencies engaged in the testing and inspection of road and
D70 Test Method for Specific Gravity and Density of
paving materials.
Semi-Solid Bituminous Materials (Pycnometer Method)
1.2 Criteria are provided for evaluating the capability of an
D92 Test Method for Flash and Fire Points by Cleveland
agencytoproperlyperformdesignatedtestsonroadandpaving
Open Cup Tester
materials, and for establishing guidelines pertaining to an
D113 Test Method for Ductility of Bituminous Materials
agency’sorganization,personnel,facilities,andqualitysystem.
D 139 Test Method for Float Test for Bituminous Materials
This specification may be supplemented by more specific
D 244 Test Methods for Emulsified Asphalts
criteria, such as that in Specification E 329, and requirements
D 1074 Test Method for Compressive Strength of Bitumi-
for particular projects.
nous Mixtures
1.3 This specification can be used as a basis to evaluate
D 1075 Test Method for Effect of Water on Compressive
testing or inspection agencies, or both, and is intended for use
Strength of Compacted Bituminous Mixtures
for the qualifying or accrediting, or both, of testing or
D 1559 Test Method for Resistance to Plastic Flow of
inspection agencies, public or private, engaged in the testing
3
Bituminous Mixtures Using Marshall Apparatus
and inspection of road and paving materials.
D 1560 Test Methods for Resistance to Deformation and
1.4 Accreditation is required to comply with this standard.
Cohesion of Bituminous Mixtures by Means of Hveem
(See 8.1.5.)
Apparatus
1.5 This standard does not purport to address all of the
D 1561 PracticeforPreparationofBituminousMixtureTest
safety concerns, if any, associated with its use. It is the
Specimens by Means of California Kneading Compactor
responsibility of the user of this standard to establish appro-
D 1754 Test Method for Effects of Heat andAir onAsphal-
priate safety and health practices and determine the applica-
tic Materials (Thin-Film Oven Test)
bility of regulatory limitations prior to use.
D 1856 Test Method for Recovery ofAsphalt from Solution
2. Referenced Documents by Abson Method
D 2041 Test Method for Theoretical Maximum Specific
2.1 The following referenced documents are those that are
Gravity and Density of Bituminous Paving Mixtures
specifically mentioned in Specification D 3666. These refer-
D 2170 Test Method for Kinematic Viscosity of Asphalts
enced documents are not meant to be all inclusive, as Speci-
(Bitumens)
fication D 3666 applies, as appropriate, to all test methods
D 2171 Test Method for Viscosity of Asphalts by Vacuum
under the jurisdiction of Committee D04.
2
Capillary Viscometer
2.2 ASTM Standards:
D 2872 TestMethodforEffectofHeatandAironaMoving
Film of Asphalt (Rolling Thin-Film Oven Test)
1
D 3143 Test Method for Flash Point of Cutback Asphalt
This specification is under the jurisdiction of ASTM Committee D04 on Road
and Paving Materials and is the direct responsibility of Subcommittee D04.95 on
with Tag Open-Cup Apparatus
Quality Control, Inspection, and Testing Agencies.
D 4402 Test Method forViscosity Determination ofAsphalt
Current edition approved Feb. 1, 2005. Published February 2005. Originally
at Elevated Temperatures Using a Rotational Viscometer
approved in 1978. Last previous edition approved in 2004 as D 3666 – 04.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
3
the ASTM website. Withdrawn.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3666–05
D 5506 Practice for Organizations Engaged in the Certifi- 5.4 The agency shall perform all testing and inspection in
cation of Personnel Testing
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3319-23(Practice)
Standard Practice for the Accelerated Polishing of Aggregates Using the British Wheel

SIGNIFICANCE AND USE
4.1 This practice simulates the polishing action of vehicular traffic on coarse aggregates used in bituminous pavements.  
4.2 A polish value is determined that may be used to rate or classify coarse aggregates for their ability to resist polishing under traffic.
Note 1: The quality of the results produced by this standard are dependant upon the competence of the personnel performing the procedure and the capability, calibration, and the maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors: following the suggestions of Specification D3666 or similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This practice covers a laboratory procedure by which an estimate may be made of the extent to which different coarse aggregates may polish.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Regarding sieves, per Specification E11: “The values stated in SI units shall be considered standard for the dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth.” When sieve mesh sizes are referenced, the alternate inch-pound designations are provided for information purposes and enclosed in parentheses.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D140/D140M-16(2023)(Practice)
Standard Practice for Sampling Asphalt Materials

SIGNIFICANCE AND USE
4.1 Sampling is as important as testing, and precautions shall be taken to obtain samples to show the true nature and condition of the materials.  
4.2 Samples are taken for either of the following two purposes:  
4.2.1 To represent as nearly as possible an average of the bulk of the materials sampled, or  
4.2.2 To ascertain the maximum variation in characteristics which the material possesses.
SCOPE
1.1 This practice applies to the sampling of asphalt materials at points of manufacture, storage, or delivery.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D517-23(Specification)
Standard Specification for Asphalt Plank

ABSTRACT
This specification covers asphalt plank used for bridge decks as well as for industrial floors. Asphalt planks shall be classified according to usage: Type Ia; Type Ib; and Type II. Asphalt plank shall be formed from a mixture of asphalt, fibers, modifiers, or a combination thereof, and mineral filler in such a manner as to produce a uniformly dense mass. The following test methods shall be intended to measure those attributes necessary to measure the ability of asphalt plank to provide a reasonably long and satisfactory service: absorption; brittleness; dimensions; and hardness.
SCOPE
1.1 This specification covers asphalt plank used for bridge decks as well as for industrial floors.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D8079-23(Practice)
Standard Practice for Preparation of Compacted Slab Asphalt Mix Samples Using a Segmented Rolling Compactor

SIGNIFICANCE AND USE
5.1 Asphalt slabs compacted with the rolling compactor can be used to obtain specimens for further testing, including bulk specific gravity following Test Methods D1188/D1188M, D2726/D2726M, and D6752/D6752M, fatigue performance characteristics following Test Methods D7460 and D8237 or AASHTO T 321, and Hamburg wheel-track testing following AASHTO T 324.  
5.2 Specimens to perform other standard tests could also be obtained, as long as their volume is contained within the volume of a slab.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this practice are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline that provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This practice covers the fabrication of slabs of asphalt mix using an automated laboratory rolling compactor (RC). Compacted specimens are suitable for volumetric and physical property testing. This practice should not be used for acceptance or rejection of a material or for purchasing purposes.  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6628-23(Specification)
Standard Specification for Color of Retroreflective Pavement Marking Materials

ABSTRACT
This specification covers the daytime and nighttime color of retroreflective pavement marking materials, both painted and tape lines, including thermoplastic, epoxy and other types, used for traffic control lane markings and symbols on road surfaces. This specification is not applicable to the testing, for quality control purposes, of marking material without added drop-on beads. The performance requirements for which the marking materials shall be tested on and conform accordingly to are the daytime and nighttime chromaticity limits, retroreflectance, and daytime lightness limits (Y tristimulus coordinate).
SCOPE
1.1 This specification covers the daytime and nighttime color of retroreflective pavement marking materials used for traffic control lane markings and symbols on road surfaces.  
1.2 This specification applies to all retroreflective pavement markings (markings that include retroreflective optics residing on the surface) except structured pavement markings as defined in 3.2.5.  
1.3 This specification is not applicable to pavement markings that do not include retroreflective optics on the surface.  
1.4 This specification does not address any requirements other than the color of retroreflective pavement markings.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5.1 Exception—This specification is noted to be an SI document, where angles are generally expressed in radians. However, as angles used in retroreflection have historically been identified in degrees, the International Committee for Weights and Measures (CIPM, Comité International des Poids et Mesures) accepts the use of degrees with SI units, and European Normatives and documents from the International Commission on Illumination (CIE) use degrees for retroreflection geometry.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM D244-23(Test Method)
Standard Test Methods and Practices for Emulsified Asphalts

SIGNIFICANCE AND USE
5.1 This test method measures the amount of water present in the emulsified asphalt, as distinguished from either bitumen or petroleum solvent.
SCOPE
1.1 These test methods and practices, given under the headings titled Composition, Consistency, Stability, and Examination of Residue, cover the examination of asphalt emulsions composed principally of a semisolid or liquid asphaltic base, water, and an emulsifying agent. The test methods cover the following tests and practices:    
Test  
Sections  
Composition:  
Water Content  
4 – 10  
Residue and Oil Distillate by Distillation  
See Test Method
D6997  
Residue by Evaporation  
See Test Method
D6934  
Particle Charge of Cationic Emulsified Asphalts  
See Practice
D7402  
Consistency:  
Viscosity (Saybolt Furol)  
See Test Method
D7496  
Stability:  
Demulsibility  
See Test Method
D6936  
Settlement  
See Test Method
D6930  
Cement Mixing  
See Test Method
D6935  
Sieve Test  
See Test Method
D6933  
Aggregate Coating  
See Practice
D6998  
Miscibility with Water  
See Practice
D6999  
Freezing  
See Practice
D6929  
Coating Ability and Water Resistance  
11 – 18  
Storage Stability of Asphalt Emulsion  
See Test Method
D6930  
Examination of Residue  
19 – 26  
Identification Test for Rapid Setting Cationic Emulsified Asphalt  
27 – 34  
Identification of Cationic Slow Set Emulsions  
See Practice
D7402  
Field Coating Test on Emulsified Asphalts  
35 – 40  
Emulsified Asphalt/Job Aggregate Coating Test  
41 – 46  
Density of Emulsified Asphalt  
See Test Method
D6937  
Residue by Low-Temperature Vacuum Distillation  
See Test Method
D7403  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D6373-23(Specification)
Standard Specification for Performance-Graded Asphalt Binder

ABSTRACT
This specification covers asphalt binders graded by performance. Grading designations are related to the average seven-day maximum pavement design temperature, and minimum pavement design temperature. Asphalt binder shall be prepared by the refining of crude petroleum by suitable methods, with or without the addition of modifiers, which may be any organic material of suitable manufacture that is used in virgin or recycled condition, and that is dissolved, dispersed or reacted in asphalt cement to enhance its performance. This specification incorporates an aid for determining the critical low cracking temperature using a combination of test procedures.
SCOPE
1.1 This specification2 covers asphalt binders graded by performance. Grading designations are related to the LTPPBind Online calculated maximum pavement design temperature and the minimum pavement design temperature. This specification contains Tables 1 and 2. Table 2 incorporates Practice D6816 for determining the critical low cracking temperature using a combination of Test Method D6648 and Test Method D6723 test procedures. If no table is specified, the default is Table 1.
Note 1: For more information on LTPPBind Online, see https://infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed May 23, 2023.
Note 2: For asphalt cements graded by penetration at 25 °C, see Specification D946/D946M. For asphalt cements graded by viscosity at 60 °C, see Specification D3381/D3381M.
Note 3: AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM D3633/D3633M-23(Test Method)
Standard Test Method for Electrical Resistivity of Membrane-Pavement Systems

SIGNIFICANCE AND USE
4.1 This test method for measuring the electrical resistivity of water-barrier membrane-pavement systems may be interpreted to indicate the effectiveness of such systems.  
4.2 This test method is predicated on the fact that an electrical connection between the surface of the pavement and the reinforcing steel in the concrete pavement cannot be made through an impermeable water-barrier membrane.  
4.3 This test method may be used for acceptance when the accepting agency specifies the minimum resistance value desired.  
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the measurement of the electrical resistivity of water-barrier membrane-pavement systems when applied to concrete bridge decks.  
1.2 Measurements shall be performed on the bituminous pavement surface covering the water-barrier membrane.  
1.3 This test method utilizes a measure of electrical resistance between the saturated top surface of the water-barrier membrane and the reinforcing steel embedded in the concrete bridge deck.  
1.4 The values measured represent the electrical resistance obtained with the equipment and procedures stated herein and do not necessarily agree or correlate with those using other equipment or procedures.  
1.5 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8239-23(Specification)
Standard Specification for Performance-Graded Asphalt Binder Using the Multiple Stress Creep and Recovery (MSCR) Test

SCOPE
1.1 This specification2 covers asphalt binders graded by performance. Grading designations are related to the LTPPBind Online calculated maximum pavement design temperature, the minimum pavement design temperature, and the traffic loading.
Note 1: For more information on LTPPBind Online, see https://infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed May 23, 2023.  
1.2 This specification incorporates Test Method D7405 for determining non-recoverable creep compliance, Jnr. “S,” “H,” “V,” or “E” designations must be specified for standard, heavy, very heavy, and extremely heavy traffic loading, respectively.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
Note 2: A guidance document for specifying bodies using R % for elastic properties is under development.
Note 3: For asphalt binders graded by penetration at 25 °C, see Specification D946/D946M. For asphalt binders graded by viscosity at 60 °C, see Specification D3381/D3381M. For performance-graded asphalt binder, see Specification D6373.
Note 4: AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off