ASTM A701/A701M-10(2015)
(Specification)Standard Specification for Ferromanganese-Silicon
Standard Specification for Ferromanganese-Silicon
ABSTRACT
This specification covers ferromanganese-silicon alloy. The alloys which are available in different sizes shall conform to the required chemical composition for manganese, carbon, silicon, phosphorus, arsenic, tin, lead, and chromium.
SCOPE
1.1 This specification covers a manganese-silicon alloy.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.2.1 This specification is expressed in both inch-pound units and in SI units (within the text, the SI units are shown in brackets); however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A701/A701M −10 (Reapproved 2015)
Standard Specification for
Ferromanganese-Silicon
This standard is issued under the fixed designationA701/A701M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* mentary requirements that are indicated in the purchase order.
Failure to comply with the general requirements of Specifica-
1.1 This specification covers a manganese-silicon alloy.
tion A1025 constitutes nonconformance with this specification.
1.2 Units—The values stated in either SI units or inch-
Incaseofconflictbetweentherequrementsofthisspecification
pound units are to be regarded separately as standard. The
and Specification A1025, this specification shall prevail.
values stated in each system may not be exact equivalents;
therefore, each system shall be used independently of the other.
4. Chemical Requirements
Combining values from the two systems may result in non-
4.1 The alloy shall conform to the chemical requirements as
conformance with the standard.
specified in Table 1 and Table 2.
1.2.1 This specification is expressed in both inch-pound
4.2 The manufacturer shall furnish an analysis of each
units and in SI units (within the text, the SI units are shown in
shipment showing the percentage of each element specified.
brackets); however, unless the purchase order or contract
specifies the applicable M specification designation (SI units),
5. Size
the inch-pound units shall apply.
5.1 The alloy is available in the sizes shown in Table 3.
2. Referenced Documents
5.2 The sizes listed in Table 3 are typical of the product as
2.1 ASTM Standards:
shipped from the seller’s plant. Some deterioration of size can
A1025 Specification for Ferroalloys and Other Alloying
be expected in transit.
Materials, General Requirements
6. Chemical Analysis
3. General Conditions for Delivery
6.1 Chemical methods are subject to agreement between the
3.1 Materials furnished to this specification shall conform to
purchaser and supplier.
the requirements of SpecificationA1025, including any supple-
6.2 Special Analysis Requirements—Analysis for additional
This specification is under the jurisdiction of ASTM Committee A01 on Steel, elements other than those listed in Tables 1 and 2 shall be
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
agreed upon between the purchaser and the manufacturer. Such
A01.18 on Castings.
elements in trace quantities shall be reported as less than “<”
Current edition approved Nov. 1, 2015. Published November 2015. Originally
the limit of analytical equipment. This shall be agree
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A701/A701M − 10 A701/A701M − 10 (Reapproved 2015)
Standard Specification for
Ferromanganese-Silicon
This standard is issued under the fixed designation A701/A701M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers a manganese-silicon alloy.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard.
1.2.1 This specification is expressed in both inch-pound units and in SI units (within the text, the SI units are shown in brackets);
however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units
shall apply.
2. Referenced Documents
2.1 ASTM Standards:
A1025 Specification for Ferroalloys and Other Alloying Materials, General Requirements
3. General Conditions for Delivery
3.1 Materials furnished to this specification shall conform to the requirements of Specification A1025, including any
supplementary requirements that are indicated in the purchase order. Failure to comply with the general requirements of
Specification A1025 constitutes nonconformance with this specification. In case of conflict between the requrements of this
specification and Specification A1025, this specification shall prevail.
4. Chemical Requirements
4.1 The alloy shall conform to the chemical requirements as specified in Table 1 and Table 2.
4.2 The manufacturer shall furnish an analysis of each shipment showing the percentage of each element specified.
5. Size
5.1 The alloy is available in the sizes shown in Table 3.
5.2 The sizes listed in Table 3 are typical of the product as shipped from the seller’s plant. Some deterioration of size can be
expected in transit.
6. Chemical Analysis
6.1 Chemical methods are subject to agreement between the purchaser and supplier.
6.2 Special Analysis Requirements—Analysis for additional elements other than those listed in Tables 1 and 2 shall be agreed
upon between the purchaser and the manufacturer. Such elements in trace quantities shall be reported as less than “<” the limit
of analytical equipment. This shall be agreed upon between the purchaser and the manufacturer.
7. Keywords
7.1 Ferromanganese-silicon
This specification is under the jurisdiction of ASTM Committee A01 o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.