ENV 14062-1:2001

Identification card systems - Surface transport applications - Electronic fee collection - Part 1: Physical characteristics, electronic signals and transmission protocols

This European Prestandard specifies directly or by reference the physical characteristics, electronic signals and transmission protocols for integrated circuit(s) cards (ICCs) carrying the EFC application and related requirements for On-Board-Units (OBUs) used in Electronic Fee Collection systems based on Dedicated Short Range Communication and Global System for Mobile Communication, with the target to provide basic interoperability between an ICC and an OBU independently of the respective manufacturers and operators. It takes into consideration both environmental and system related aspects and states minimum requirements of conformity.
The requirements imposed by this Prestandard apply to :
· the IC card itself, denoted by the abbreviation ICC ;
· the in-vehicle card interface device, denoted by the abbreviation OBU ; or
· the combination of both.
This Prestandard does not directly set requirements on any other card interface device (IFD) besides the OBU e.g. stationary devices. However, the requirements imposed on the IC card may induce technical consequences for an IFD designed to accept an IC card used in EFC applications.
It specifies the respective characteristics of the ICC and OBU only as far as these may concern the interface, but does not give any internal technical implementation.

Sistemi z identifikacijskimi karticami - Aplikacije za prevoze po kopnem - Elektronsko pobiranje pristojbin - 1. del: Fizikalne značilnosti, elektronski signali in protokoli prenosa

Ta evropski predstandard neposredno ali s sklicem določa fizikalne značilnosti, elektronske signale in protokole prenosa za kartice z integriranim vezjem (ICC) z aplikacijo elektronskega pobiranja pristojbin ter povezane zahteve za enote v vozilu (OBU), ki se uporabljajo v sistemih za elektronsko pobiranje pristojbin (EFC) na osnovi namenske komunikacije kratkega dosega in globalnega sistema mobilnih komunikacij s ciljem zagotavljanja osnovne interoperabilnosti med kartico z integriranim vezjem in enoto v vozilu neodvisno od zadevnih proizvajalcev in operaterjev. Obravnava okoljske in s sistemom povezane vidike ter navaja minimalne zahteve za skladnost.
Zahteve, ki jih nalaga ta predstandard, se uporabljajo za:
samo kartico z integriranim vezjem, ki jo označuje okrajšava ICC;
vmesniško napravo za kartice v vozilu, ki jo označuje okrajšava OBU, ali
kombinacijo obojega.
Ta predstandard neposredno ne določa zahtev za katero koli drugo vmesniško napravo za kartice (IFD) poleg enote v vozilu, npr. stacionarne naprave. Vendar pa zahteve, ki veljajo za kartico z integriranim vezjem, lahko imajo tehnične posledice za vmesniško napravo za kartice, zasnovano za sprejem kartice z integriranim vezjem, ki se uporablja v aplikacijah elektronskega pobiranja pristojbin.
Zadevne značilnosti kartice z integriranim vezjem in enote v vozilu določa samo v meri, v kateri te zadevajo vmesnik, ne podaja pa nikakršne notranje tehnične izvedbe.

General Information

• Status: Withdrawn
• Publication Date: 19-Jun-2001
• Withdrawal Date: 13-Apr-2025
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: CEN/TC 224 - Machine-readable cards, related device interfaces and operations
• Drafting Committee: CEN/TC 224 - Machine-readable cards, related device interfaces and operations
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 17-Jun-2020
• Completion Date: 14-Apr-2025
• Directive: 93/89/EEC - Taxes on certain vehicles used for the carriage of goods by road and tolls and charges for the use of certain infrastructures
• Mandate: M/211 - Standardization mandate forwarded to CEN/CENELEC/ETSI in the field of information technology and telecommunications concerning Standards for IC cards for road toll collection
• Ref Project: SIST ENV 14062-1:2018 - Identification card systems - Surface transport applications - Electronic fee collection - Part 1: Physical characteristics, electronic signals and transmission protocols

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2018
6LVWHPL]LGHQWLILNDFLMVNLPLNDUWLFDPL$SOLNDFLMH]DSUHYR]HSRNRSQHP
(OHNWURQVNRSRELUDQMHSULVWRMELQGHO)L]LNDOQH]QDþLOQRVWLHOHNWURQVNLVLJQDOL
LQSURWRNROLSUHQRVD
Identification card systems - Surface transport applications - Electronic fee collection -
Part 1: Physical characteristics, electronic signals and transmission protocols
Ta slovenski standard je istoveten z: ENV 14062-1:2001
ICS:
35.240.15 ,GHQWLILNDFLMVNHNDUWLFHýLSQH Identification cards. Chip
NDUWLFH%LRPHWULMD cards. Biometrics
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN PRESTANDARD
ENV 14062-1
PRÉNORME EUROPÉENNE
EUROPÄISCHE VORNORM
June 2001
ICS 35.240.15
English version
Identification card systems - Surface transport applications -
Electronic fee collection - Part 1: Physical characteristics,
electronic signals and transmission protocols
This European Prestandard (ENV) was approved by CEN on 10 May 2001 as a prospective standard for provisional application.
The period of validity of this ENV is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the ENV can be converted into a European Standard.
CEN members are required to announce the existence of this ENV in the same way as for an EN and to make the ENV available promptly
at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the ENV) until the final
decision about the possible conversion of the ENV into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. ENV 14062-1:2001 E
worldwide for CEN national Members.

Page 2
Contents
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions.6
4 Abbreviations .6
5 EFC using DSRC .7
5.1 Physical characteristics.7
5.1.1 General. 7
5.1.2 Temperature . 7
5.1.3 Embossing. 8
5.1.4 Provision of contacts. 8
5.1.5 Insertion-removal endurance. 8
5.1.6 Toxicity. 8
5.2 Electronic signals and electrical characteristics under normal operating conditions.8
5.2.1 VCC. 8
5.2.2 CLK. 8
5.2.3 VPP . 8
5.3 Transmission protocols .9
5.3.1 General. 9
5.3.2 Answer-To-Reset. 9
5.3.3 Transmission bit rate. 9
5.3.4 Protocol switching. 9
5.3.5 Protocol Type T = 1. 10
5.3.6 Protocol Type T = 0. 11
5.3.7 Error handling protocols. 12
6 EFC using GSM .12
Bibliography .13

Page 3
Foreword
This European Prestandard has been prepared by Technical Committee CEN/TC 224, "Machine readable cards,
related device interfaces and operations" the secretariat of which is held by AFNOR.
This European Prestandard comprises the following parts, under the general title “Identification card systems –
Surface transport applications – Electronic fee collection”:

Part 1 : Physical characteristics, electronic signals and transmission protocols

Part 2 : Message requirements

Part 3 : Application and security aspects

Part 4 : Test procedures
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this European Prestandard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
Switzerland and the United Kingdom.

Page 4
Introduction
This European Prestandard is one of a series of Standards describing the characteristics of IC cards used in
Electronic Fee Collection (EFC) systems based on :
 the Dedicated Short Range Communication (DSRC) ; and
 the Global System for Mobile Communication (GSM) ;
and the characteristics of the interface between those IC cards and the related card interface devices installed in
vehicles, so-called On-Board-Units.

Page 5
1 Scope
This European Prestandard specifies directly or by reference the physical characteristics, electronic signals and
transmission protocols for integrated circuit(s) cards (ICCs) carrying the EFC application and related requirements
for On-Board-Units (OBUs) used in Electronic Fee Collection systems based on Dedicated Short Range
Communication and Global System for Mobile Communication, with the target to provide basic interoperability
between an ICC and an OBU independently of the respective manufacturers and operators. It takes into
consideration both environmental and system related aspects and states minimum requirements of conformity.
The requirements imposed by this Prestandard apply to :
 the IC card itself, denoted by the abbreviation ICC ;
 the in-vehicle card interface device, denoted by the abbreviation OBU ; or
 the combination of both.
This Prestandard does not directly set requirements on any other card interface device (IFD) besides the OBU e.g.
stationary devices. However, the requirements imposed on the IC card may induce technical consequences for an
IFD designed to accept an IC card used in EFC applications.
It specifies the respective characteristics of the ICC and OBU only as far as these may concern the interface, but
does not give any internal technical implementation.
2 Normative references
This European Prestandard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Prestandard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 726-3:1994, Identification card systems – Telecommunications integrated circuit(s) cards and terminals –
Part 3 : Application independent card requirements.
ENV 1375-1:1994, Identification card systems – Intersector integrated circuit(s) card additional formats – Part 1 :
ID-000 card size and physical characteristics.
ENV 1855:1996, Identification card systems – Intersector integrated circuit(s) card systems – Tolerance ranges for
IC cards.
ETS 300 641, European digital cellular telecommunications system (Phase 2) ; Specification of the 3 Volt
Subscriber Identity Module – Mobile Equipment (SIM – ME) interface (GSM 11.12 V 4.2.0).
ETS 300 699, European digital cellular telecommunications system (Phase 2+) – Specification of the Subscriber
Identity Module – Mobile Equipment (SIM – ME) interface (GSM 11.11 V 5.5.0).
ISO/IEC 7810:1995, Identification cards — Physical characteristics.
ISO/IEC 7811-1:1995, Identification cards — Recording technique — Part 1 : Embossing.
ISO/IEC 7811-3:1995, Identification cards — Recording technique — Part 3 : Location of embossed characters on
ID-1 cards.
ISO/IEC 7812-1: 1993, Identification cards — Identification of Issuers — Numbering system.
ISO/IEC 7816-1:1998, Identification cards — Integrated circuit(s) cards with contacts — Part 1 : Physical
characteristics.
ISO/IEC 7816-2:1999, Identification cards — Integrated circuit(s) cards with contacts — Part 2 : Dimensions and
location of the contacts.
Page 6
ISO/IEC 7816-3:1997, Identification cards — Integrated circuit(s) cards with contacts — Part 3 : Electronic signals
and transmission protocols.
ISO/IEC 7816-4:1995, Identification cards — Integrated circuit(s) cards with contacts — Part 4 : Inter-industry
commands for interchange.
3 Terms and definitions
For the purposes of this European Prestandard, the following terms and definitions apply.
3.1
IC card, ICC
an integrated circuit(s) card used in EFC applications
3.2
interface device, IFD
any interface device foreseen to accept an IC card used in EFC applications
3.3
on-board-unit, OBU
in-vehicle, card interface device, containing DRSC or GSM communication equipment, enabling direct or in-direct
communication between an IC card and a roadside beacon or between an IC card and the GSM network
4 Abbreviations
For the purpose of this European Prestandard, the following abbreviations apply throughout the document unless
otherwise specified :
EFC Electronic Fee Collection
APDU Application Protocol Data Unit, according to ISO/IEC 7816-4:1995
ATR Answer To Reset
CLK The contact delivering the clock-signal to the ICC
D
Bit rate adjustment factor, as defined in ISO/IEC 7816-3:1997
DSRC Dedicated Short Range Communication
EDC Error Detection Code
Etu elementary time unit, according to ISO/IEC 7816-3:1997
F Clock rate conversion factor, as defined in ISO/IEC 7816-3:1997
IC Integrated circuit
ICC
IC card
I Current at the contact VCC
cc
IFD Interface Device
INF
Information Field, as defined in ISO/IEC 7816-3:1997
I/O Contact used for bi-directional data exchange with the ICC
LEN
Length field
Page 7
NAD Node Address, as defined in ISO/IEC 7816-3:1997
OBU On-Board-Unit
PCB Protocol Control Byte, as defined in ISO/IEC 7816-3:1997
PPS
Protocol and Parameters Selection, as defined in ISO/IEC 7816-3:1997
RST Contact delivering the reset-signal to the ICC
TPDU Transport Protocol Data Unit, according to ISO/IEC 7816-3:1997
V Supply voltage at VCC
cc
VCC Contact delivering the supply voltage to the ICC
V
Programming voltage at VPP
pp
VPP
Contact for delivering programming voltage to the ICC
5 EFC using DSRC
5.1 Physical characteristics
Requirements on physical characteristics include card size, card thickness, dimensions and locations of the
contacts etc.
5.1.1 General
The ICC shall be an ICC with contacts as defined in ISO/IEC 7816-2:1999. Thus the physical characteristics
specified for ICC in ISO/IEC 7816-1:1998 shall apply unless otherwise stated in this standard. This means, among
other things, that the dimensions of the ICC shall be those of the type ID-1 as defined in Table 1
of ISO/IEC 7810:1995.
...