EN ISO 8099-1:2018
(Main)Small craft - Waste systems - Part 1: Waste water retention (ISO 8099-1:2018)
Small craft - Waste systems - Part 1: Waste water retention (ISO 8099-1:2018)
ISO 8099-1:2018 specifies requirements for the design, construction and installation of systems for temporary retention of sewage for subsequent disposal. It applies to small craft with a length of hull (LH) of up to 24 m.
ISO 8099-1:2018 does not address waste water treatment systems.
Kleine Wasserfahrzeuge - Abfallsysteme - Teil 1: Abwasserrückhaltung (ISO 8099-1:2018)
Dieses Dokument legt die Anforderungen für Entwurf, Konstruktion und Einbau von Anlagen für das vorübergehende Sammeln von Abwasser fest, das später entsorgt wird. Es gilt für kleine Wasser¬fahrzeuge mit einer Rumpflänge (LH) bis 24 m.
Dieses Dokument gilt nicht für Abwasseraufbereitungssysteme.
Petits navires - Circuits d'eaux usées - Partie 1 : Rétention des eaux usées (ISO 8099-1:2018)
ISO 8099-1:2018 spécifie les exigences relatives à la conception, à la construction et à l'installation des systèmes de rétention temporaire des eaux usées avant évacuation. Elle s'applique aux petits navires d'une longueur de coque (LH) inférieure ou égale à 24 m.
ISO 8099-1:2018 ne concerne pas les systèmes de traitement des eaux usées.
Mala plovila - Sistemi ravnanja z odpadki - 1. del: Zadrževanje odpadne vode (ISO 8099-1:2018)
Ta dokument določa zahteve za načrtovanje, izdelavo in namestitev sistemov za začasno zadrževanje odplak za naknadno odstranjevanje. Uporablja se za mala plovila z dolžino trupa (LH) največ 24 m.
Ta dokument ne obravnava čistilnih naprav za odpadno vodo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2018
1DGRPHãþD
SIST EN ISO 8099:2001
Mala plovila - Sistemi ravnanja z odpadki - 1. del: Zadrževanje odpadne vode (ISO
8099-1:2018)
Small craft - Waste systems - Part 1: Waste water retention (ISO 8099-1:2018)
Kleine Wasserfahrzeuge - Toilettenabfall-Sammelanlagen (ISO 8099-1:2018)
Petits navires - Circuits d'eaux usées - Partie 1: Rétention des eaux usées (ISO 8099-
1:2018)
Ta slovenski standard je istoveten z: EN ISO 8099-1:2018
ICS:
13.030.01 Odpadki na splošno Wastes in general
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8099-1
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 8099:2000
English Version
Small craft - Waste systems - Part 1: Waste water retention
(ISO 8099-1:2018)
Petits navires - Circuits d'eaux usées - Partie 1 : Kleine Wasserfahrzeuge - Abfallsysteme - Teil 1:
Rétention des eaux usées (ISO 8099-1:2018) Abwasserrückhaltung (ISO 8099-1:2018)
This European Standard was approved by CEN on 2 February 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8099-1:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4
European foreword
This document (EN ISO 8099-1:2018) has been prepared by Technical Committee ISO/TC 188 "Small
craft".
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall
be withdrawn at the latest by August 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8099:2000.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8099-1:2018 has been approved by CEN as EN ISO 8099-1:2018 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request
M/542 C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding Essential Requirements
of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of
Directive 2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) of Remarks/Notes
Directive 2013/53/EU this EN
Annex I, Part A, 2.5 – Owner’s 11
manual
Annex I, Part A, 5.8 – Discharge 4, 5, 6, 7, 8, 9 This standard only deals with
prevention and installations discharge from toilets and the
facilitating the delivery ashore of delivery ashore of toilet waste; it
waste. does not deal with:
• the accidental discharge of
pollutants such as oil, fuel and
bilge water overboard or;
• water treatment systems.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 8099-1
First edition
2018-02
Small craft — Waste systems —
Part 1:
Waste water retention
Petits navires — Circuits d'eaux usées —
Partie 1: Rétention des eaux usées
Reference number
ISO 8099-1:2018(E)
©
ISO 2018
ISO 8099-1:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 8099-1:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative reference . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Materials . 3
6 Plumbing system . 3
6.1 Hoses and piping . 3
6.2 Seacock fitting . 3
7 Vent system . 3
7.1 Venting of gases . 3
7.1.1 Heel angles . 3
7.1.2 Inside diameter of fittings. 3
7.1.3 Prevention of clogging — Pressure resistance . 4
7.1.4 Flow area . 4
7.2 Venting of tanks . 4
7.2.1 Rigid tanks with capacity of less than 400 l . 4
7.2.2 Rigid tanks with capacity of 400 l and greater . 4
7.2.3 Venting of flexible tanks . 4
8 Holding tanks . 4
8.1 General requirements . 4
8.1.1 Fastening . 4
8.1.2 Indication of contents level . 4
8.1.3 Accessibility of fittings and connections . 4
8.1.4 Access opening . 5
8.1.5 Tank walls . 5
8.2 Requirements for permanently installed holding tanks . 5
8.3 Requirements for portable holding tanks . 5
9 Pump-out fitting . 5
10 Identification . 6
11 Information for owner's manual . 6
Annex A (normative) Nominal design of pump-out fitting . 7
Annex B (informative) Typical installations for toilet retention systems .9
ISO 8099-1:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.