EN 4028:2001
(Main)Aerospace series - Pipe coupling 8°30' in titanium alloy - Tees with thrust wire nut on run
Aerospace series - Pipe coupling 8°30' in titanium alloy - Tees with thrust wire nut on run
This standard specifies the characteristics of tees, with thrust wire nut on run, for pipe couplings 8°30', in titanium alloy, for
aerospace applications.
Nominal pressure: up to 28 000 kPa
Temperature range: 55 C to 135 C
Luft- und Raumfahrt - Rohrverschraubung 8°30' aus Titanlegierung - T-Verschraubungen T-Durchgang mit Mutter mit Schubdraht
Diese Norm legt die Eigenschaften von T-Verschraubungen, T-Durchgang mit Mutter mit Schubdraht, für Rohrver-
schraubungen 8 30', aus Titanlegierung, zur Verwendung in der Luft- und Raumfahrt fest.
Nenndruck: bis 28 000 kPa
Temperaturbereich: 55 C bis 135 C
Série aérospatiale - Système de raccordement 8°30' en alliage de titane - Raccords en té avec écrou à jonc en ligne
La présente norme spécifie les caractéristiques des raccords en té avec écrou à jonc en ligne, pour les systèmes de
raccordement 8°30', en alliage de titane, pour applications aérospatiales.
Pression nominale: jusqu'à 28 000 kPa
Plage de température: 55 °C à 135 °C
Aerospace series - Pipe coupling 8°30' in titanium alloy - Tees with thrust wire nut on run
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Pipe coupling 8°30' in titanium alloy - Tees with thrust wire nut on runLuft- und Raumfahrt - Rohrverschraubung 8°30' aus Titanlegierung - T-Verschraubungen T-Durchgang mit Mutter mit SchubdrahtSérie aérospatiale - Systeme de raccordement 8°30' en alliage de titane - Raccords en té avec écrou a jonc en ligneAerospace series - Pipe coupling 8°30' in titanium alloy - Tees with thrust wire nut on run49.080Aerospace fluid systems and componentsICS:Ta slovenski standard je istoveten z:EN 4028:2001SIST EN 4028:2004en01-maj-2004SIST EN 4028:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 4028October 2001ICS 49.080English versionAerospace series - Pipe coupling 8°30' in titanium alloy - Teeswith thrust wire nut on runSérie aérospatiale - Système de raccordement 8°30' enalliage de titane - Raccords en té avec écrou à jonc enligneLuft- und Raumfahrt - Rohrverschraubung 8°30' ausTitanlegierung - T-Verschraubungen T-Durchgang mitMutter mit SchubdrahtThis European Standard was approved by CEN on 29 December 2000.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4028:2001 ESIST EN 4028:2004
ScopeThis standard specifies the characteristics of tees, with thrust wire nut on run, for pipe couplings 8°30', in titanium alloy, foraerospace applications.Nominal pressure: up to 28 000 kPaTemperature range:
55 °C to 135 °C2
Normative referencesThis European Standard incorporates by dated or undated reference provisions from other publications. These normativereferences are cited at the appropriate places in the text and the publications are listed hereafter. For dated references,subsequent amen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.