CEN/TS 1329-2:2018
(Main)Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
This document gives guidance for the assessment of conformity of materials (formulations), products and assemblies in accordance with EN 1329 1 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1 It is advised that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [2].
NOTE 2 If certification is involved, it is advised that the certification body is preferably compliant with EN ISO/IEC 17065 [6] or EN ISO/IEC 17021 1 [4], as applicable.
NOTE 3 In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1329 1, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC U) intended to be used for the following purposes:
- for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B");
- for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 4 This is reflected in the marking of products by "B" or "BD".
Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Dieses Dokument gibt Hinweise für die Beurteilung der Konformität von Werkstoffen (Zusammensetzungen), Erzeugnissen und Bauteilkombinationen nach EN 1329 1, die als Teil des Qualitätsmanagementsystems im Qualitätsplan des Herstellers und für die Einführung von Zertifizierungsverfahren vorgesehen sind.
ANMERKUNG 1 Es wird empfohlen, dass das Qualitätsmanagementsystem EN ISO 9001 [2] oder mindestens ebenso strengen Anforderungen entspricht.
ANMERKUNG 2 Bei Zertifizierung wird empfohlen, dass die Zertifizierungsstelle in Abhängigkeit von der Anwendung vorzugsweise nach EN ISO/IEC 17065 [6] oder EN ISO/IEC 17021 1 [4] zugelassen ist.
ANMERKUNG 3 Zur Unterstützung der Leser enthält Anhang A eine grundlegende Prüfmatrix.
Dieses Dokument gilt in Verbindung mit EN 1329 1 für Rohrleitungssysteme aus weichmacherfreiem Polyvinylchlorid (PVC U) für folgende vorgesehene Verwendungszwecke:
- zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebäuden (Anwendungskennzeichen "B" [en: inside buildings]);
- zum Ableiten von Abwasser (niedriger und hoher Temperatur) sowohl innerhalb von Gebäuden und erdverlegt innerhalb der Gebäudestruktur (Anwendungskennzeichen "BD" [en: inside buildings and buried in ground within the building structure]).
ANMERKUNG 4 Dies spiegelt sich in den Kennzeichnungen "B" bzw. "BD" der Erzeugnisse wider.
Systèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2: Guide pour l'évaluation de la conformité
Cevni sistemi iz polimernih materialov za (nizko- in visokotemperaturne) odvodne sisteme v zgradbah - Nemehčan polivinilklorid (PVC-U) - 2. del: Navodilo za ugotavljanje skladnosti
Ta dokument vsebuje navodila za ugotavljanje skladnosti materialov (formulacij), izdelkov in sestavov s standardom EN 13291, pri čemer naj bi se te informacije vključile v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti in za vzpostavitev postopka certificiranja.
OPOMBA 1 Priporočljivo je, da je sistem vodenja kakovosti skladen s standardom EN ISO 9001 [2] oziroma da ni manj strog od ustreznih zahtev iz tega standarda.
OPOMBA 2 Pri certificiranju je priporočljivo, da je certifikacijski organ akreditiran v skladu s standardom EN ISO/IEC 17065 [6] ali EN ISO/IEC 17021 [4].
OPOMBA 3 V pomoč bralcem dodatek A vsebuje osnovno preskusno matriko.
Ta dokument se v povezavi s standardom EN 13291 uporablja za cevne sisteme iz nemehčanega polivinilklorida (PVC-U), ki naj bi se uporabljali za:
– (nizko- in visokotemperaturne) odvodne sisteme v stavbah (koda območja uporabe »B«).
– (nizko- in visokotemperaturne) odvodne sisteme v zgradbah in sisteme, vkopane v zgradbah (koda območja uporabe »BD«).
OPOMBA 4 To je razvidno iz oznak »B« in »BD« na izdelkih.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2018
1DGRPHãþD
SIST-TS CEN/TS 1329-2:2012
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]D QL]NRLQYLVRNRWHPSHUDWXUQH RGYRGQH
VLVWHPHY]JUDGEDK1HPHKþDQSROLYLQLONORULG 39&8 GHO 1DYRGLOR]D
XJRWDYOMDQMHVNODGQRVWL
Plastics piping systems for soil and waste discharge (low and high temperature) within
the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for
the assessment of conformity
Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher
Temperatur) innerhalb der Gebäudestruktur - Weichmacherfreies Polyvinylchlorid (PVC-
U) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux
usées (à basse et à haute température) à l'intérieur de la structure des bâtiments - Poly
(chlorure de vinyle) non plastifié (PVC-U) - Partie 2: Guide pour l'évaluation de la
conformité
Ta slovenski standard je istoveten z: CEN/TS 1329-2:2018
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
91.140.80 Drenažni sistemi Drainage systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN/TS 1329-2
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
June 2018
TECHNISCHE SPEZIFIKATION
ICS 23.040.01; 91.140.80 Supersedes CEN/TS 1329-2:2012
English Version
Plastics piping systems for soil and waste discharge (low
and high temperature) within the building structure -
Unplasticized poly(vinyl chloride) (PVC-U) - Part 2:
Guidance for the assessment of conformity
Systèmes de canalisations en plastique pour Kunststoff-Rohrleitungssysteme zum Ableiten von
l'évacuation des eaux-vannes et des eaux usées (à Abwasser (niedriger und hoher Temperatur) innerhalb
basse et à haute température) à l'intérieur de la der Gebäudestruktur - Weichmacherfreies
structure des bâtiments - Poly(chlorure de vinyle) non Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für
plastifié (PVC-U) - Partie 2: Guide pour l'évaluation de die Beurteilung der Konformität
la conformité
This Technical Specification (CEN/TS) was approved by CEN on 24 December 2017 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 1329-2:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Abbreviated terms . 10
5 General . 10
6 Testing and inspection . 10
6.1 Material specification . 10
6.2 Grouping . 11
6.2.1 General . 11
6.2.2 Size groups . 11
6.2.3 Fitting groups . 12
6.3 Type testing . 12
6.4 Batch release tests . 15
6.5 Process verification tests . 17
6.6 Audit tests . 18
6.7 Indirect tests . 21
6.8 Test records . 21
Annex A (informative) Basic test matrix . 22
Bibliography . 23
European foreword
This document (CEN/TS 1329-2:2018) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 1329-2:2012.
Compared to the previous version, this document has been updated according to the latest version of
EN 1329-1.
EN 1329 consists of the following parts, under the general title "Plastics piping systems for soil and waste
discharge (low and high temperature) within the building structure — Unplasticized poly(vinyl chloride)
(PVC-U)":
— Part 1: Specifications for pipes, fittings and the system
— Part 2: Guidance for the assessment of conformity (the present document)
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Introduction
Figures 1 and 2 are intended to provide general information on the concept of testing and organization
of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type test
(TT), batch release test (BRT), process verification test (PVT) and audit test (AT), this part of EN 1329
details the applicable characteristics to be assessed and the frequency and sampling of testing.
A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings, valves or
assemblies by manufacturers is given in Figure 1.
Figure 1 — Typical scheme for the assessment of conformity by a manufacturer
A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings, valves or
assemblies by manufacturers, including certification, is given in Figure 2.
Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including
certification
1 Scope
This document gives guidance for the assessment of conformity of materials (formulations), products
and assemblies in accordance with EN 1329-1 intended to be included in the manufacturer’s quality
plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1 It is advised that the quality management system conforms to or is no less stringent than the relevant
requirements to EN ISO 9001 [2].
NOTE 2 If certification is involved, it is advised that the certification body is preferably compliant with
EN ISO/IEC 17065 [6] or EN ISO/IEC 17021-1 [4], as applicable.
NOTE 3 In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1329-1, this document is applicable to piping systems made of unplasticized
poly(vinyl chloride) (PVC-U) intended to be used for the following purposes:
— for soil and waste discharge systems (low and high temperature) inside buildings (application area
code "B");
— for soil and waste discharge systems (low and high temperature) for both inside buildings and
buried in ground within the building structure (application area code "BD").
NOTE 4 This is reflected in the marking of products by "B" or "BD".
2 Normative references
The following documents are referred to in the text in such a way that some of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 1329-1:2014+A1:2018, Plastics piping systems for soil and waste discharge (low and high
temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1:
Specifications for pipes, fittings and the systems
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1329-1 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
Note 1 to entry: A certification body is preferably compliant with EN ISO/IEC 17065 [6].
3.2
inspection body
body, that performs inspection
Note 1 to entry: An inspection body can be an organization or part of an organization.
[SOURCE: EN ISO/IEC 17020:2012 [3], definition 3.5]
Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 [3].
3.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
Note 1 to entry: In the context of this part of EN 1329, the materials and products can be subjected to type
testing, batch release testing, process verification testing, audit testing and witness testing, as applicable.
Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 [5].
3.4
quality management system
part of a management system with regard to quality
[SOURCE: EN ISO 9000:2015 [1], definition 3.5.4]
Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [2].
3.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.6
type testing
TT
testing performed to prove that the material, product, joint or assembly is capable of conforming to the
requirements given in the relevant standard
Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly
provided that the process verification tests are done regularly.
3.7
batch release test
BRT
test performed by or on behalf of the manufacturer on a batch of materials or products, which needs to
be satisfactorily completed before the batch can be released
3.8
process verification test
PVT
test performed by, or on behalf of the manufacturer on materials, p
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.