This part of EN 1329 specifies the requirements for solid wall unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and the system intended for:
-   soil and waste discharge applications (low and high temperature) inside buildings (application area code "B");
-   soil and waste discharge applications (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 1   The intended use is reflected in the marking of products by "B" or "BD".
NOTE 2   For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm.
This part of EN 1329 is also applicable to PVC-U pipes, fittings and the system intended for the following purposes:
-   ventilating part of the pipework in association with discharge applications;
-   rainwater pipework within the building structure.
It also specifies the test parameters for the test method referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
For external above ground application additional requirements depending on the climate should be agreed between the manufacturer and the user.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 24.
NOTE 5   Joints and adhesives are considered to be part of the system as covered in the scope.

  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives guidance for the assessment of conformity of materials (formulations), products and assemblies in accordance with EN 1329 1 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1   It is advised that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [2].
NOTE 2   If certification is involved, it is advised that the certification body is preferably compliant with EN ISO/IEC 17065 [6] or EN ISO/IEC 17021 1 [4], as applicable.
NOTE 3   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1329 1, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC U) intended to be used for the following purposes:
-   for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B");
-   for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 4   This is reflected in the marking of products by "B" or "BD".

  • Technical specification
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC U) piping systems in the field of non-pressure underground drainage and sewerage:
- buried in ground outside the building structure (application area code "U"), and
- both buried in ground, within the building structure and outside the building (application area code "UD").
NOTE 1   The intended use is reflected in the marking of products by "U" or "UD".
It also specifies the test parameters for the test methods referred to in this document.
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 13476-2 [1].
This document covers a range of nominal sizes, a range of pipes and fittings series and a range of stiffness classes and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to PVC U pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 16.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Specification gives guidance for the assessment of conformity of compounds/formulations, products and assemblies in accordance with EN 1401 1. It applies to those compounds/formulations, products and assemblies intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements of EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to either EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
NOTE 3   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1401 1 (see Foreword), this Technical Specification is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC-U) used for the following puposes:
-   for non pressure underground drainage and sewerage outside the building structure (application area code "U"), reflected in the marking of products by "U";
-   for non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure (application area code "U"), reflected in the marking of products by "UD".

  • Technical specification
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Specification gives guidance for the assessment of conformity of materials (compounds/formulations), products and assemblies in accordance with EN 1565 1 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements of EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
NOTE 3   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1565 1, this document is applicable to solid-wall piping systems made of styrene copolymer blends (SAN+PVC) intended to be used for the following purposes:
-   for soil and waste discharge (low and high temperature) inside buildings (application area code "B");
-   for soil and waste discharge (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 4   This is reflected in the marking of products by "B" or "BD".

  • Technical specification
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the requirements for pipes, fittings and the system of styrene copolymer blends (SAN+PVC) solid-wall piping systems in the field of soil and waste discharge (low and high temperature) inside buildings (marked with "B") and for soil and waste discharge systems for both inside buildings and buried in ground within the building structure (marked with "BD"). Note 1: The application area "inside buildings" according to this standard, applies to the interior area of the building only.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Part of EN 1401 specifies the requirements for solid wall pipes, fittings and the system of unplasticized poly(vinyl chloride) (PVC U) piping systems in the field of non-pressure underground drainage and sewerage:
a)   outside the building structure (application area code "U") and
b)   both buried in ground within the building structure (application area code "D") and outside the building.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipes and fittings series and a range of stiffness classes and gives recommendations concerning colours.
NOTE 1   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with prCEN/TS 1401-2 [1] and ENV 1401-3 [2] it is applicable to PVC U pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This European Standard is applicable to non foamed PVC U pipes without a socket as well as pipes with an integral socket.
The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
Requirements and limiting values for application area code "D" are given in Table 4, Table 6, Table 13 and Table 15.
NOTE 2   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 15.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Specification gives guidance for the assessment of conformity of compounds/formulations, products and assemblies in accordance with EN 1329 1 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
NOTE 3   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1329 1, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC U) intended to be used for the following purposes:
-   for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B");
-   for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 4   This is reflected in the marking of products by "B" or "BD".

  • Technical specification
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of EN 1329 specifies the requirements for solid wall unplasticised poly(vinyl chloride) (PVC-U) pipes, fittings and the system intended for:
-   soil and waste discharge applications (low and high temperature) inside buildings (application area code "B");
-   soil and waste discharge applications (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 1   The intended use is reflected in the marking of products by "B" or "BD".
NOTE 2   For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm.
This part of EN 1329 is also applicable to PVC-U pipes, fittings and the system intended for the following purposes:
-   ventilating part of the pipework in association with discharge applications;
-   rainwater pipework within the building structure.
It also specifies the test parameters for the test method referred to in this standard.
This standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
For external above ground application additional requirements depending on the climate should be agreed between the manufacturer and the user.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 15.
NOTE 5   Joints and adhesives are considered to be part of the system as covered in the scope.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies a method for testing the mechanical strength or flexibilty of a fabricated thermoplastics fitting intended to be used in non-pressure underground applications.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Prestandard gives guidance for the assessment of conformity to be included in the manufacturer's quality plans as part of the quality system. This prestandard includes: a) Requirements for materials, pipes, joints and assemblies given in EN 1453-1;  b) Requirements for the manufacturer's quality system; NOTE 1: It is recommended that the quality system conforms to EN ISO 9001 or EN ISO 9002, as applicable. c) Definitions and procedures to be applied if third party certification is involved.

  • Standardization document
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the requirements for pipes, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems with structured-wall pipes intended to be used for soil and waste discharge (low and high temperature) inside buildings (marked with "B"). It also specifies the test parameters for the test methods referred to in this standard. It covers pipes with an external and internal smooth layer which are connected with faomed PVC-U or by radial legs in solid PVC-U. The fully foamed PVC-U pipes and spiraly wound PVC-U pipes are not covered by this standard.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the requirements for pipes, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems in the field of soil and waste discharge (low and high temperature) inside buildings (marked with "B") and for soil and waste discharge systems for both inside buildings and buried in ground within the building structure (marked with "BD").

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of prEN 1329 specifies procedures and requirements for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system for third party certification of conformity by a certification body accredited to EN 45011 or EN 45012, as applicable. This standard includes: a) Requirements for materials, components, joints and assemblies given in prEN 1329-1. b) Requirements for the manufacturer's quality system given in EN ISO 9001 or EN ISO 9002, as applicable.

  • Standardization document
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Part of EN 1401 gives guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system. This standard includes:a)requirements for materials, components, joints and assemblies given in EN 1401-1; b) requirements for the manufacture's quality system (NOTE:it is recommended that the quality system conforms to EN ISO 9001 or EN ISO 9002,asapplicable); c) definitions and procedures to be applied if a third party certification is involved (NOTE:if third party is involved, it is recommended that the certification body is accredited to EN 45011 or EN 45012, as applicable.)

  • Standardization document
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day