EN 12163:2024
(Main)Copper and copper alloys - Rod for general purposes
Copper and copper alloys - Rod for general purposes
This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy rod in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding intended for general purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.
Kupfer und Kupferlegierungen - Stangen zur allgemeinen Verwendung
Dieses Dokument legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenzabmaße für durch Ziehen oder Pressen endgefertigte Stangen aus Kupferlegierungen in runder, quadratischer, sechseckiger oder achteckiger Form zur allgemeinen Verwendung fest.
Der Ablauf der Probenahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieses Dokuments sind ebenfalls festgelegt.
Cuivre et alliages de cuivre - Barres pour usages généraux
Le présent document spécifie la composition, les exigences de propriétés et les tolérances dimensionnelles des barres en alliages de cuivre de forme ronde, carrée, hexagonale ou octogonale, fabriquées par étirage ou filage, destinées à des usages généraux.
Les modes opératoires d’échantillonnage et les méthodes d’essai pour la vérification de la conformité aux exigences du présent document sont également spécifiés.
Baker in bakrove zlitine - Palice za splošno uporabo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Baker in bakrove zlitine - Palice za splošno uporabo
Copper and copper alloys - Rod for general purposes
Kupfer und Kupferlegierungen - Stangen zur allgemeinen Verwendung
Cuivre et alliages de cuivre - Barres pour usages généraux
Ta slovenski standard je istoveten z: EN 12163:2024
ICS:
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 12163
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2024
EUROPÄISCHE NORM
ICS 77.150.30 Supersedes EN 12163:2016
English Version
Copper and copper alloys - Rod for general purposes
Cuivre et alliages de cuivre - Barres pour usages Kupfer und Kupferlegierungen - Stangen zur
généraux allgemeinen Verwendung
This European Standard was approved by CEN on 30 June 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12163:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Designations. 8
4.1 Material . 8
4.1.1 General . 8
4.1.2 Symbol . 8
4.1.3 Number . 8
4.2 Material condition . 8
4.3 Product . 8
5 Ordering information .10
6 Requirements .12
6.1 Composition .12
6.2 Mechanical properties .12
6.3 Resistance to dezincification .12
6.4 Residual stress level .12
6.5 Dimensions and tolerances .12
6.5.1 Diameter or width across-flats .12
6.5.2 Shape tolerances .12
6.5.3 Straightness .12
6.5.4 Length .13
6.5.5 Corner radii .13
6.5.6 Twist of polygonal rod .13
6.6 Surface quality.14
6.7 Internal inclusion .14
7 Sampling .14
7.1 General .14
7.2 Analysis .14
7.3 Mechanical tests .14
7.4 Dezincification resistance and stress corrosion resistance test .14
8 Test methods .15
8.1 Analysis .15
8.2 Tensile test .15
8.2.1 General .15
8.2.2 Location of test pieces .15
8.2.3 Shape and size of test pieces .15
8.2.4 Procedure for testing .15
8.2.5 Determination of results .15
8.3 Hardness test .16
8.4 Dezincification resistance test .16
8.5 Stress corrosion resistance test . 16
8.6 Determination of the electrical conductivity . 16
8.7 Retests . 16
8.7.1 Analysis, tensile, hardness and dezincification resistance tests and determination of
the electrical conductivity . 16
8.7.2 Stress corrosion resistance test . 17
8.8 Rounding of results . 17
9 Certificate of compliance and inspection documentation . 17
9.1 Certificate of compliance . 17
9.2 Inspection documentation . 17
10 Marking, packaging, labelling . 17
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/68/EU (Pressure equipment Directive) aimed to be
covered . 43
Bibliography . 44
European foreword
This document (EN 12163:2024) has been prepared by Technical Committee CEN/TC 133 “Copper and
copper alloys”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2025, and conflicting national standards shall be
withdrawn at the latest by April 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12163:2016.
In comparison with EN 12163:2016, the following significant technical changes were made:
a) Introduction of 6.7 Internal inclusion;
b) Modified the definition of diameter or width across-flats at 6.5.1;
c) Added a new Figure for straightness at 6.5.3 and modified values in Table 18
d) CuSi4Zn4MnP (CW245E) and CuSi4Zn9MnP (CW246E) added in the new Table 2 and new Table 10
e) CuSn5 (CW451K) added in Table 6 and Table 14;
f) Introduction in the chemical composition Tables of a footnote to explain the meaning of elements for
which no upper and lower limits are specified;
g) Annex ZA added.
This document is one of a series of European Standards for the copper and copper alloy products rod,
wire, profile and forgings. Other products are specified as follows:
— EN 12164, Copper and copper alloys — Rod for free machining purposes;
— EN 12165, Copper and copper alloys — Wrought and unwrought forging stock;
— EN 12166, Copper and copper alloys — Wire for general purposes;
— EN 12167, Copper and copper alloys — Profiles and bars for general purposes;
— EN 12168, Copper and copper alloys — Hollow rod for free machining purposes;
— EN 13601, Copper and copper alloys — Copper rod, bar and wire for general electrical purposes;
— EN 13602, Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical
conductors;
— EN 13605, Copper and copper alloys — Copper profiles and profiled wire for electrical purposes.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
Introduction
The European Committee for Standardization (CEN) draws attention to the fact that it is claimed that
compliance with this document may involve the use of a patent concerning the alloys
CuSi4Zn4MnP (CW245E) and CuSi4Zn9MnP (CW246E) given in 6.1.
CEN takes no position concerning the evi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.