CEN/TC 133/WG 4 - Extruded and drawn products, forgings and scrap

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy profiles including L-, T-, U-shaped cross-sections, and bars, finally produced by drawing or extruding.
This European Standard applies to profiles with L-, T- and U-shaped cross-sections which would fit within a circumscribing circle of a maximum 180 mm diameter and to bars with thicknesses from 3 mm up to and including 60 mm and with widths from 6 mm up to and including 120 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.

This document specifies the composition, property requirements and dimensional tolerances for copper alloy rod, in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding, especially intended for free machining purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this document are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy rod in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding intended for general purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This document specifies the composition, property requirements and dimensional tolerances for copper alloy hollow rod, finally produced by drawing or extruding, specifically intended for free machining purposes.
NOTE   Hollow products having an outside diameter greater than 80 mm and/or a wall thickness less than 2 mm are most frequently specified in EN 12449.
The sampling procedures, the methods of test for verification of conformity to the requirements of this document, are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for forging stock of copper and copper alloys.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This document specifies the composition, property requirements and dimensional tolerances for copper alloy wire, finally produced by drawing, rolling or extruding, intended for general purposes, spring and fastener manufacturing applications.
The sampling procedures and the methods of test for verification of conformity to the requirements of this document are also specified.

This European Standard specifies the composition, the property requirements and tolerances on dimensions and form for copper and copper alloy die and hand forgings.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This document specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper profiles and profiled wire for electrical purposes, which would fit within a circumscribing circle of maximum 180 mm diameter.
The sampling procedures, the test methods for verification of conformity to the requirements of this document, and the delivery conditions are also specified.

This document specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross-sections and size ranges are:
— round, square and hexagonal rod with diameters or widths across-flats from 2 mm up to and including 160 mm;
— bar with thicknesses from 2 mm up to and including 40 mm and widths from 3 mm up to and including 250 mm;
— round, square, hexagonal and rectangular wire with diameters or widths across-flats from 2 mm up to and including 25 mm, as well as thicknesses from 0,5 mm up to and including 12 mm with widths from 1 mm up to and including 250 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this document are also specified.
NOTE Drawn, round copper wire, plain or tinned, single or multiline, for the manufacture of electrical conductors is specified in EN 13602.

This document specifies methods for assessing the tin coating on drawn round copper wire for the manufacture of electrical conductors, e.g. according to EN 13602.
This document includes test methods for the determination of the following characteristics:
a) thickness of the unalloyed tin coating;
b) continuity of the tin coating;
c) adherence of the tin coating.
WARNING — This document can involve the use of hazardous materials, operations, and equipment. This document does not purport to address all of the safety problems associated with their use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Moreover this document does not cover the aspects related to the people protection against the X-ray. To obtain information applicable to this aspect, it is convenient to refer to national and international standards, and also to the local regulations if they exist.

This document specifies a procedure for fully automatic eddy current testing with no operator involvement with an encircling test coil for detecting defects on the surface of copper and copper alloy rods, bars, hollow rods and wires with a minimum diameter or width across flats defined in the relevant product standards.
This test method can be continuous or discontinuous depending on the product.
The product size range and test acceptance level are defined in the relevant product standards.

This European Standard specifies the requirements for characteristics, condition, moisture, composition, metal content, metal yield and test procedures of metallic raw materials for direct melting (melting grades) in the form of copper and copper alloy scrap.
All provisions of this European Standard apply regardless of the legal status of the scrap. The respective legal requirements should be met.

This European Standard specifies the composition, property requirements including electrical properties and tolerances on dimensions and form of semiconductor devices, electronic and vacuum products in two copper grates Cu-OFE (CW009A) and Cu-PHCE (CW022A), in the form of wrought products, e.g. plate, sheet, strip, seamless tube, rod, bar, wire, profiles.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, and the delivery conditions are also specified.
This European Standard applies to the wrought copper products as delivered to the device manufacturer, i.e. for further fabrication.

This European Standard specifies the composition, property requirements including electrical properties, and dimensional tolerances for drawn round copper wire from 0,04 mm up to and including 5,0 mm for the manufacture of electrical conductors intended for the production of bare and insulated cables and flexible cords.
This standard covers plain or tinned, single or multiline, annealed or hard drawn wire. It does not include wire for enamelling (winding wire, magnet wire), for electronic application and for contact wire for electric traction.
The sampling procedures, the test methods for verification of conformity to the requirements of this standard and the delivery conditions are also specified.
NOTE   Due to the thermal and/or mechanical treatment involved in cablemaking processes, the properties of conductors in the final cable or cord differ from those of the original wire supplied. Requirements for conductors taken from cable or cord are given in appropriate cable standards.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy rod in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding intended for general purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy wire, finally produced by drawing, rolling or extruding, intended for general purposes, spring and fastener manufacturing applications.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy rod, in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding, especially intended for free machining purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy profiles including L-, T-, U-shaped cross-sections, and bars, finally produced by drawing or extruding.
This European Standard applies to profiles with L-, T- and U-shaped cross-sections which would fit within a circumscribing circle of a maximum 180 mm diameter and to bars with thicknesses from 3 mm up to and including 60 mm and with widths from 6 mm up to and including 120 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy hollow rod, finally produced by drawing or extruding, specifically intended for free machining purposes.
NOTE   Hollow products having an outside diameter greater than 80 mm and/or a wall thickness less than 2 mm are specified in EN 12449.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for forging stock of copper and copper alloys.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This European Standard specifies the composition, the property requirements and tolerances on dimensions and form for copper and copper alloy die and hand forgings.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross sections and size ranges are:
-   round, square and hexagonal rod with diameters or widths across flats from 2 mm up to and including 160 mm;
-   bar with thicknesses from 2 mm up to and including 40 mm and widths from 3 mm up to and including 200 mm;
-   round, square, hexagonal and rectangular wire with diameters or widths across flats from 2 mm up to and including 25 mm, as well as thicknesses from 0,5 mm up to and including 12 mm with widths from 1 mm up to and including 200 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this standard are also specified.
NOTE   Drawn, round copper wire - plain or tinned, single or multiline - for the manufacture of electrical conductors is specified in EN 13602.

This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper profiles and profiled wire for electrical purposes, which would fit within a circumscribing circle of maximum 180 mm diameter.
The sampling procedures, the test methods for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This European Standard specifies methods for assessing the tin coating on drawn round copper wire for the manufacture of electrical conductors, e.g. according to EN 13602.
This European Standard includes test methods for the determination of the following characteristics:
a)   thickness of the unalloyed tin coating;
b)   continuity of the tin coating;
c)   adherence of the tin coating.
WARNING - This European Standard can involve the use of hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with their use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for seamless drawn copper tubes for electrical purposes, delivered in straight lengths or alternatively in level wound coils with the cross-sections and size ranges below:
-   for round tubes in straight lengths with outside diameters from 3 mm up to and including 450 mm and wall thicknesses from 0,3 mm;
-   for round tubes in level wound coils with outside diameters from 3 mm up to and including 30 mm and wall thicknesses from 0,3 mm;
-   for square and rectangular tubes with major outside dimension from 5 mm up to and including 150 mm and wall thicknesses from 0,5 mm up to and including 10 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this standard are also specified.

This European Standard specifies the requirements for characteristics, condition, moisture, composition, metal content, metal yield and test procedures of secondary raw materials for direct melting (melting grades) in the form of copper and copper alloy scrap.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy rod, in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding, especially intended for free machining purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy rod in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding intended for general purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy wire, finally produced by drawing, rolling or extruding, intended for general purposes, spring and fastener manufacturing applications.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for forging stock of copper and copper alloys.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy profiles including L-, T-, U-shaped cross-sections, and bars, finally produced by drawing or extruding.
This European Standard applies to profiles with L-, T- and U-shaped cross-sections which would fit within a circumscribing circle of a maximum 180 mm diameter and to bars with thicknesses from 3 mm up to and including 60 mm and with widths from 6 mm up to and including 120 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy hollow rod, finally produced by drawing or extruding, specifically intended for free machining purposes.
NOTE   Hollow products having an outside diameter greater than 80 mm and/or a wall thickness less than 2 mm are specified in EN 12449.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.

TC - Modification to value in Table 12

This European Standard specifies the composition, property requirements including electrical properties and
tolerances on dimensions and form of two copper grades Cu-OFE (CW009A) and Cu-PHCE (CW022A), for
electronic and semiconductor devices as well as for vacuum applications, in the form of wrought products, e.g. plate,
sheet, strip, seamless tube, rod, bar, wire, profiles.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and
the delivery conditions are also specified.
This European Standard applies to the wrought copper products as delivered to the device manufacturer, i.e. for
further fabrication.

This European Standard specifies the composition, property requirements including electrical properties, and
tolerances on dimensions and form for copper profiles and profiled wire for electrical purposes which would fit within
a circumscribing circle of maximum 180 mm diameter.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and
the delivery conditions are also specified.

This European Standard specifies the composition, property requirements including electrical properties, and
dimensional tolerances for drawn round copper wire from 0,04 mm up to and including 5,0 mm for the manufacture
of electrical conductors intended for the production of bare and insulated cables and flexible cords.
This standard covers plain or tinned, single or multiline, annealed or hard drawn wire. It does not include wire for
enamelling (winding wire, magnet wire), for electronic application and for contact wire for electric traction.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard and
the delivery conditions are also specified.
NOTE   Due to the thermal and/or mechanical treatment involved in cablemaking processes, the properties of conductors in the
final cable or cord differ from those of the original wire supplied. Requirements for conductors taken from cable or cord are given
in appropriate cable standards.

This European Standard specifies the composition, property requirements including electrical properties, and
tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross-sections and
size ranges are:
         round, square and hexagonal rod with diameters or widths across-flats from 2 mm up to and including 80 mm;
         rectangular bar with thicknesses from 2 mm up to and including 40 mm and widths from 3 mm up to and
         including 200 mm;
         round, square, hexagonal and rectangular wire with diameters or widths across-flats from 2 mm up to and
         including 25 mm, as well as thicknesses from 0,5 mm up to and including 12 mm with widths from 1 mm up to
         and including 200 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard and
the delivery conditions are also specified.
NOTE   Drawn, round copper wire   plain or tinned, single or multiline   for the manufacture of electrical conductors is specified
in prEN 13602.

This European Standard specifies the composition, property requirements including electrical properties, and
tolerances on dimensions and form for seamless drawn copper tubes for electrical purposes, delivered in straight
lengths with the cross-sections and size ranges below:
         for round tubes with outside diameters from 5 mm up to and including 150 mm and wall thicknesses from
         0,5 mm up to and including 20 mm;
         for square and rectangular tubes with major outside dimension from 5 mm up to and including 150 mm and wall
         thicknesses from 0,5 mm up to and including 10 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and
the delivery conditions are also specified.

This European Standard specifies methods for assessing the tin coating on drawn round copper wire for the
manufacture of electrical conductors, e.g. according to prEN 13602.
Standard includes test methods for the determination of the following characteristics:
a)   thickness of the unalloyed tin coating;
b)   continuity of the tin coating;
c)   adherence of the tin coating.
WARNING   This standard can involve the use of hazardous materials, operations, and equipment. This
standard does not purport to address all of the safety problems associated with their use. It is the responsi-
bility of the user of this standard to establish appropriate safety and health practices and determine the
applicability of regulatory limitations prior to use.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper and copper alloy rod and wire intended for welding and braze welding purposes.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This European Standard specifies the composition, property requirements and tolerances on dimensions and form for seamless round copper capillary tubes for use as metering lines for liquids or gases where close controls over the smoothness and dimensions of the bore are required to ensure uniform flow characteristics.

This European Standard specifies the composition, property requirements and tolerances on dimensions and form for seamless round drawn copper and copper alloy tubes for heat exchangers, condensers, evaporators and desalination equipment, supplied in the size range from 6 mm up to and including 76 mm outside diameter and from 0,5 mm up to and including 3 mm wall thickness.  The sampling procedures and the methods of test for verification of conformity to the requirements of this standard are also specified.

This European Standard specifies the composition, property requirements and tolerances on dimensions and form for rolled, finned, seamless copper and copper alloy tubes for heat exchangers supplied in the size range from 6 mm up to and including 35 mm outside diameter and from 1 mm up to and including 3 mm wall thickness of the unfinned section with fin height up to and including 1,5 mm.  The sampling procedures and the methods of test for verification of conformity to the requirements of this standard are also specified.

This European standard specifies the composition, property requirements and tolerances on dimensions and form for seamless round drawn copper and copper alloy tubes for general purposes supplied in the size range from 3 mm up to and including 450 mm outside diameter and from 0,3 mm up to and including 20 mm wall thickness. The sampling procedures and the methods of test for verification of conformity to the requirements of this standard are also specified.

Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months (TC Res 11/1998) (CC/981029)

Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months (TC Res 11/1998) (CC/981029)

This European Standard specifies the composition, property requirements and dimensional tolerances for copper and copper alloy round rod supplied in straight lengths, specifically intended for forging. This standard is also applicable to regular polygonal rod, hollow rod, rectangular bar and profiles intended for forging. The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper and copper alloy wire intended for general purposes, spring and fastener manufacturing applications. The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper and copper alloy rod supplied in straight lengths, intended for general purposes. The sampling procedures and the methods of test for verification of conformity to the requirements of this standard are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper and copper alloy profiles and rectangular bars supplied in straight lengths. This standard applies to rectangular bar with thicknesses from 3 mm up to and including 60 mm and with widths from 6 mm up to and including 120 mm. The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.