EN ISO 16000-26:2012
(Main)Indoor air - Part 26: Sampling strategy for carbon dioxide (CO2) (ISO 16000-26:2012)
Indoor air - Part 26: Sampling strategy for carbon dioxide (CO2) (ISO 16000-26:2012)
ISO 16000-26:2012 specifies the planning of carbon dioxide indoor pollution measurements. In the case of indoor air measurements, the careful planning of sampling and the entire measurement strategy are of particular significance since the result of the measurement can have far-reaching consequences, for example, with regard to ascertaining the need for remedial action or the success of such an action.
An inappropriate measurement strategy can lead to misrepresentation of the true conditions or, worse, to erroneous results.
ISO 16000-26:2012 is not applicable to the measurement strategy for carbon monoxide (CO).
Innenraumluftverunreinigungen - Teil 26: Probenahmestrategie für Kohlendioxid (CO2) (ISO 16000-26:2012)
In diesem Teil der ISO 16000 werden Anforderungen für die Planung von Messungen von Kohlendioxid als
Innenraumluftschadstoff festgelegt. Die sorgfältige Planung der Probenahme und der gesamten Messstrategie
sind bei Innenraumluftuntersuchungen von besonderer Tragweite, da das Untersuchungsergebnis erhebliche
Konsequenzen haben kann, so z. B. hinsichtlich der Festlegung eines Sanierungsbedarfs oder des Erfolgs
einer Sanierung.
Eine ungeeignete Messstrategie kann zu einer erheblichen Gesamtunsicherheit oder sogar zu fehlerhaften
Messergebnissen beitragen.
Dieser Teil der ISO 16000 behandelt die Messstrategie zur Bestimmung von Kohlendioxid (CO2), aber nicht
die von Kohlenmonoxid (CO) in der Innenraumluft.
Air intérieur - Partie 26: Stratégie d'échantillonnage du dioxyde de carbone (CO2) (ISO 16000-26:2012)
L'ISO 16000-26:2012 spécifie la planification des mesurages de la pollution de l'air intérieur par le dioxyde de carbone. En cas de mesurages dans l'air intérieur, il est particulièrement important de soigneusement planifier l'échantillonnage ainsi que l'ensemble de la stratégie de mesure car le résultat du mesurage peut avoir de lourdes conséquences, par exemple en ce qui concerne l'évaluation des besoins en termes de mesure corrective ou le succès d'une telle mesure.
Une stratégie de mesure inappropriée peut fausser l'interprétation des conditions réelles, ou pire, donner des résultats erronés.
L'ISO 16000-26:2012 n'est pas applicable à la stratégie de mesure du monoxyde de carbone (CO).
Notranji zrak - 26. del: Strategija vzorčenja ogljikovega dioksida (CO2) (ISO 16000-26:2012)
Ta del standarda ISO 16000 določa načrtovanje meritev onesnaževanja z ogljikovim dioksidom v zaprtih prostorih. V primeru meritev zraka v zaprtih prostorih, sta zelo pomembna skrbno načrtovanje vzorčenja in celotna strategija merjenja, ker ima rezultat merjenja lahko dolgoročne posledice, na primer v zvezi z določanjem potrebe po sanacijskem ukrepu ali uspešnosti tega dejanja. Posledica neustrezne strategije merjenja je lahko nepravilna predstavitev dejanskih pogojev ali celo nepravilni rezultati. Ta del standarda ISO 16000 ne velja za strategijo merjenja za ogljikov monoksid (CO).
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2012
1RWUDQML]UDNGHO 6WUDWHJLMDY]RUþHQMDRJOMLNRYHJDGLRNVLGD &2 ,62
Indoor air - Part 26: Sampling strategy for carbon dioxide (CO2) (ISO 16000-26:2012)
Innenraumluftverunreinigungen - Teil 26: Probenahmestrategie für Kohlendioxid (CO2)
(ISO 16000-26:2012)
Air intérieur - Partie 26: Stratégie d'échantillonnage du dioxyde de carbone (CO2) (ISO
16000-26:2012)
Ta slovenski standard je istoveten z: EN ISO 16000-26:2012
ICS:
13.040.20 Kakovost okoljskega zraka Ambient atmospheres
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 16000-26
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2012
ICS 13.040.20
English Version
Indoor air - Part 26: Sampling strategy for carbon dioxide (CO )
(ISO 16000-26:2012)
Air intérieur - Partie 26: Stratégie d'échantillonnage du Innenraumluftverunreinigungen - Teil 26:
dioxyde de carbone (CO2) (ISO 16000-26:2012) Probenahmestrategie für Kohlendioxid (CO2) (ISO 16000-
26:2012)
This European Standard was approved by CEN on 31 July 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16000-26:2012: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 16000-26:2012) has been prepared by Technical Committee ISO/TC 146 "Air quality"
in collaboration with Technical Committee CEN/TC 264 “Air quality” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2013, and conflicting national standards shall be withdrawn
at the latest by February 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16000-26:2012 has been approved by CEN as a EN ISO 16000-26:2012 without any
modification.
INTERNATIONAL ISO
STANDARD 16000-26
First edition
2012-08-01
Indoor air —
Part 26:
Sampling strategy for carbon dioxide (CO )
Air intérieur —
Partie 26: Stratégie d’échantillonnage du dioxyde de carbone (CO )
Reference number
ISO 16000-26:2012(E)
©
ISO 2012
ISO 16000-26:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 16000-26:2012(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Properties, origin and occurrence of carbon dioxide . 1
4 Measurement technique . 4
5 Measurement planning . 4
5.1 General . 4
5.2 Measurement objective and boundary conditions . 4
5.3 When to measure . 5
5.4 Measurement location . 6
5.5 Measurement period . 6
5.6 Measurement uncertainty and presentation of result . 6
5.7 Quality assurance . 7
5.8 Test report . 7
Annex A (informative) Calculation of the ventilation requirement . 8
Annex B (informative) Regulations . 11
Annex C (informative) Examples of screening tests and of continuously registering measuring devices
for CO and CO .12
Bibliography .13
ISO 16000-26:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16000-26 was prepared by Technical Committee ISO/TC 146, Air quality, Subcommittee SC 6, Indoor air.
ISO 16000 consists of the following parts, under the general title Indoor air —:
— Part 1: General aspects of sampling strategy
— Part 2: Sampling strategy for formaldehyde
— Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air —
Active sampling method
— Part 4: Determination of formaldehyde — Diffusive sampling method
— Part 5: Sampling strategy for volatile organic compounds (VOCs)
— Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on
Tenax TA® sorbent, thermal desorption and gas chromatography using MS or MS-FID
— Part 7: Sampling strategy for determination of airborne asbestos fibre concentrations
— Part 8: Determination of local mean ages of air in buildings for characterizing ventilation conditions
— Part 9: Determination of the emission of volatile organic compounds from building products and furnishing —
Emission test chamber method
— Part 10: Determination of the emission of volatile organic compounds from building products and
furnishing — Emission test cell method
— Part 11: Determination of the emission of volatile organic compounds from building products and
furnishing — Sampling, storage of samples and preparation of test specimens
— Part 12: Sampling strategy for polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins
(PCDDs), polychlorinated dibenzofurans (PCDFs) and polycyclic aromatic hydrocarbons (PAHs)
— Part 13: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs) and
polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/PCDFs) — Collection on sorbent-backed filters
— Part 14: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs) and
polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/PCDFs) — Extraction, clean-up and analysis
by high-resolution gas chromatography and mass spectrometry
— Part 15: Sampling strategy for nitrogen dioxide (NO2)
— Part 16: Detection and enumeration of moulds — Sampling by filtration
iv © ISO 2012 – All rights reserved
ISO 16000-26:2012(E)
— Part 17: Detection and enumeration of moulds — Culture-based method
— Part 18: Detection and enumeration of moulds — Sampling by impaction
— Part 19: Sampling strategy for moulds
— Part 21: Detection and enumeration of moulds — Sampling from materials
— Part 23: Performance test for evaluating the reduction of formaldehyde concentrations by sorptive
building materials
— Part 24: Performance test for evaluating the reduction of volatile organic compound (except formaldehyde)
concentrations by sorptive building materials
— Part 25: Determination of the emission of semi-volatile organic compounds by building products — Micro-
chamber method
— Part 26: Sampling strategy for carbon dioxide (CO )
— Part 28: Determination of odour emissions from building products using test chambers
— Part 29: Test methods for VOC detectors
— Part 30: Sensory testing of indoor air
— Part 31: Measurement of flame retardants and plasticizers based on organophosphorus compounds —
Phosphoric acid ester
The following parts are under preparation:
— Part 27: Determination of settled fibrous dust on surfaces by SEM (scanning electron microscopy)
(direct method)
— Part 32: Investigation of buildings for pollutants and other injurious factors — Inspections
ISO 16000-26:2012(E)
Introduction
In ISO 16000-1, general requirements relating to the measurement of indoor air pollutants and the important
conditions to be observed before or during the sampling of individual pollutants or groups of pollutants are described.
This part of ISO 16000 describes basic aspects to be considered when working out a sampling strategy for
the measurements of carbon dioxide in indoor air. It is intended to be a link between ISO 16000-1 and the
analytical procedures.
This part of ISO 16000 presupposes knowledge of ISO 16000-1.
This part of ISO 16000 uses the definition for indoor environment defined in ISO 16000-1 and Reference
[12] as dwellings having living rooms, bedrooms, DIY (do-it-yourself) rooms, recreation rooms and cellars,
kitchens and bathrooms; workrooms or work places in buildings which are not subject to health and safety
inspections with regard to air pollutants (for exa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.