EN 1007-1:2002
(Main)Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 1: Determination of size content
Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 1: Determination of size content
This part of EN 1007 specifies a method for the determination of the size content of ceramic fibres, including silicon carbide, silicon nitride, silicon carbon-nitride, alumino-silicate, alumina or silicon oxide fibres.
Hochleistungskeramik - Keramische Verbundwerstoffe - Verfahren zur Prüfung der Faserverstärkungen - Teil 1: Bestimmung des Schlichtegehaltes
Dieser Teil von EN 1007 legt die Bedingungen zur Bestimmung des Schlichtegehaltes von Keramikfasern einschließlich Siliciumcarbid-, Siliciumnitrid-, Silicumcarbonitrid-, Alumo-Silicat-, Aluminiumoxid- und Siliciumdioxidfasern fest.
ANMERKUNG In dieser Europäischen Norm werden Kohlenstoff-Fasern nicht berücksichtigt. Für Kohlenstoff-Fasern sollte EN ISO 10548 angewendet werden.
Céramiques techniques avancées - Céramiques composites - Méthodes d'essai pour renforcements - Partie 1: Détermination du taux d'ensimage
Cette partie de l'EN 1007 spécifie une méthode pour la détermination du taux d'ensimage des fibres céramiques, dont notamment le carbure de silicium, le nitrure de silicium, le carbonitrure de silicium, le silicate d'alumine, les oxydes d'aluminium ou de silicium.
NOTE Les fibres de carbone ne sont pas traitées par la présente Norme européenne. Pour les fibres de carbone, il convient de se référer à l'EN ISO 10548.
Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 1: Determination of size content
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2004
1DGRPHãþD
SIST ENV 1007-1:2000
Advanced technical ceramics - Ceramic composites - Methods of test for
reinforcement - Part 1: Determination of size content
Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement -
Part 1: Determination of size content
Hochleistungskeramik - Keramische Verbundwerstoffe - Verfahren zur Prüfung der
Faserverstärkungen - Teil 1: Bestimmung des Schlichtegehaltes
Céramiques techniques avancées - Céramiques composites - Méthodes d'essai pour
renforcements - Partie 1: Détermination du taux d'ensimage
Ta slovenski standard je istoveten z: EN 1007-1:2002
ICS:
81.060.30 Sodobna keramika Advanced ceramics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 1007-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2002
ICS 81.060.30 Supersedes ENV 1007-1:1993
English version
Advanced technical ceramics - Ceramic composites - Methods
of test for reinforcement - Part 1: Determination of size content
Céramiques techniques avancées - Céramiques Hochleistungskeramik - Keramische Verbundwerstoffe -
composites - Méthodes d'essai pour renforcements - Partie Verfahren zur Prüfung der Faserverstärkungen - Teil 1:
1: Détermination du taux d'ensimage Bestimmung des Schlichtegehaltes
This European Standard was approved by CEN on 6 July 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1007-1:2002 E
worldwide for CEN national Members.
Contents
page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4
4 Principle.4
5 Apparatus and chemicals .4
6 Test specimen .5
7 Conditioning of test specimens prior to weighing.5
8 Procedure .5
9 Calculation of results .6
10 Test report .6
Bibliography .7
Foreword
This document (EN 1007-1:2002) has been prepared by Technical Committee CEN/TC 184 "Advanced technical
ceramics", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by March 2003, and conflicting national standards shall be withdrawn at the latest by
March 2003.
This document supersedes ENV 1007-1:1993.
EN 1007 has six parts:
EN 1007-1 Part 1: Determination of size content.
EN 1007-2 Part 2: Determination of linear density.
EN 1007-3 Part 3: Determination of filament diameter and cross-section area.
prEN 1007-4 Part 4: Determination of tensile properties of filament at ambient temperature.
prEN 1007-5 Part 5: Determination of distribution of tensile strength and of tensile strain to failure of
filaments within a multifilament tow at ambient temperature.
ENV 1007-6 Part 6: Determination of tensile properties of filament at high temperature.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Net
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.