EN 2327:2006
(Main)Aerospace series - Washers, lock, with radial serrations in alloy steel, cadmium plated for flight control rods - Dimensions
Aerospace series - Washers, lock, with radial serrations in alloy steel, cadmium plated for flight control rods - Dimensions
This standard specifies the characteristics of lock washers with radial serrations primarily intended for flight control rods.
These lock washers are intended to immobilise the rod end in relation to the rod body, whilst allowing a precise positional adjustment.
Luft- und Raumfahrt - Sicherungen, radial verzahnt, aus legiertem Stahl, verkadmet für Bediengestänge von Flugsteuerungen - Maße
Diese Norm legt die Eigenschaften von radial verzahnten Sicherungen fest, die vor allem für Bediengestänge von Flugsteuerungen bestimmt sind.
Diese Sicherungen dienen dazu, den Stangenkopf gegenüber dem Rohrkörper zu arretieren und gleichzeitig eine genaue Lageeinstellung zu ermöglichen.
Série aérospatiale - Freins à stries radiales en acier allié, cadmiés pour bielles de commandes de vol - Dimensions
Aeronavtika - Zaščitne podložke, radialno ozobljene, iz legiranega jekla, s kadmijevo prevleko, za kontrolne palice pri krmiljenju - Mere
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Sicherungen, radial verzahnt, aus legiertem Stahl, verkadmet für Bediengestänge von Flugsteuerungen - MaßeSérie aérospatiale - Freins à stries radiales en acier allié, cadmiés pour bielles de commandes de vol - DimensionsAerospace series - Washers, lock, with radial serrations in alloy steel, cadmium plated for flight control rods - Dimensions49.030.50Podložke in drugi blokirni elementiWashers and other locking elementsICS:Ta slovenski standard je istoveten z:EN 2327:2006SIST EN 2327:2009en,de01-april-2009SIST EN 2327:2009SLOVENSKI
STANDARDSIST EN 2327:20011DGRPHãþD
SIST EN 2327:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2327May 2006ICS 49.030.50Supersedes EN 2327:1987
English VersionAerospace series - Washers, lock, with radial serrations in alloysteel, cadmium plated for flight control rods - DimensionsSérie aérospatiale - Freins à stries radiales en acier allié,cadmiés pour bielles de commandes de vol - DimensionsLuft- und Raumfahrt - Sicherungen, radial verzahnt, auslegiertem Stahl, verkadmet für Bediengestänge vonFlugsteuerungen - MaßeThis European Standard was approved by CEN on 26 October 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2327:2006: ESIST EN 2327:2009
EN 2327:2006 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Required characteristics.4 4 Designation.6 5 Marking.7 6 Qualification.7
SIST EN 2327:2009
EN 2327:2006 (E) 3 Foreword This European Standard (EN 2327:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2006, and conflicting national standards shall be withdrawn at the latest by November 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This European Standard supersedes EN 2327:1987. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.