iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12475-4:1998

(Main)

Classification of dense shaped refractory products - Part 4: Special products

Classification of dense shaped refractory products - Part 4: Special products

This part of EN 12475 establishes the classification and designation of dense shaped refractory products of special composition of the following series:  a) oxide based products:  alumina-chromic oxide; alumina-chromic oxide-zirconia-silica; zirconia-silica; alumina-zirconia-silica;  b) oxide and non-oxide based products: alumina-carbon; alumina-silicon carbide-carbon; etc.

Klassifizierung dichter geformter feuerfester Erzeugnisse - Teil 4: Sondererzeugnisse

Dieser Teil von EN 12475 legt die Klassifizierung und Bezeichnung der folgenden Reihen dichter geformter feuerfester Erzeugnisse mit nachstehend angeführter Zusammensetzung fest: a) oxidische Erzeugnisse: Alumina-Chromoxid; Alumina-Chromoxid-Zirconia-Silika; Zirconia-Silika; Alumina-Zirconia-Silika; b) oxidische und nichtoxidische Erzeugnisse: Alumina-Kohlenstoff; Alumina-Siliciumcarbid-Kohlenstoff; etc.

Classification des produits réfractaires façonnés denses - Partie 4: Produits spéciaux

La présente partie de la norme européenne EN 12475-4 établit la classification et la désignation des produits réfractaires façonnés denses de composition spéciale, correspondant aux séries suivantes : a) produits à base d'oxydes : alumine-oxyde de chrome; alumine-oxyde de chrome-zircone-silice; zircone-silice; alumine-zircone-silice;  b) produits à base d'oxydes et de non-oxydes : alumine-carbone; alumine-carbure de silicium-carbone; etc.

Razvrstitev gostih oblikovanih ognjevzdržnih izdelkov - 4. del.: Posebni izdelki

General Information

Status
Withdrawn
Publication Date
15-Dec-1998
Withdrawal Date
02-Sep-2014
ICS
81.080 - Refractories
Technical Committee
CEN/TC 187 - Refractory products and materials
Drafting Committee
CEN/TC 187/WG 1 - Dense shaped refractory products
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
03-Sep-2014
Ref Project
SIST EN 12475-4:2000 - Classification of dense shaped refractory products - Part 4: Special products

Relations

Replaced By
EN ISO 10081-4:2014 - Classification of dense shaped refractory products - Part 4: Special products (ISO 10081-4:2014)
Effective Date
22-May-2013

Buy Standard

EN 12475-4:2000EN 12475-4:2000
PreviousNext
Standard
EN 12475-4:2000
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Razvrstitev gostih oblikovanih ognjevzdržnih izdelkov - 4. del.: Posebni izdelkiKlassifizierung dichter geformter feuerfester Erzeugnisse - Teil 4: SondererzeugnisseClassification des produits réfractaires façonnés denses - Partie 4: Produits spéciauxClassification of dense shaped refractory products - Part 4: Special products81.080Ognjevzdržni materialiRefracto
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 20182:2024(Main)
Refractory test-piece preparation - Gunning refractory panels by the pneumatic-nozzle mixing type guns (ISO 20182:2024)
SIST EN ISO 20182:2024

This document describes the procedure for the preparation of test panels from refractory materials by gunning through pneumatic nozzle mixing type guns at ambient temperatures. The test pieces are for the determination of properties on as-gunned products prepared under either “standard conditions” (as required for quality assurance or product development) or “site conditions”. In the case of “site conditions”, the purpose of the testing is to establish the properties pertaining to a given installation or a given set of installation conditions. In this case, the panel can be obtained during the on-site installation. Parameters such as ambient temperature, gunning elevation, air pressure and curing conditions (temperature, orientation of the panel) applicable during the preparation of the panel are as near as possible to the respective parameters pertaining to the site installation.
It is also possible to simulate certain “site conditions” by gunning panels off-site, for example, in a laboratory setting. This is acceptable under this document, by agreement between interested parties.
This document does not apply to plastic gunning mixes and to those mixes that contain aggregates that are susceptible to hydration.
This document does not apply to shotcrete type mixes, which are dealt with in ISO 18886.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21068-2:2024(Main)
Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 2: Determination of volatile components, total carbon, free carbon, silicon carbide, total and free silicon, free and surface silica (ISO 21068-2:2024)
SIST EN ISO 21068-2:2024

This document specifies analytical techniques for the determination of volatile components by thermal treatment at specified temperatures, and methods for the determination of the total carbon, free carbon, silicon carbide, total and free silicon and free and surface silica content of silicon-carbide, silicon-nitride and silicon-oxynitride containing raw materials and refractory products.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21068-3:2024(Main)
Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 3: Determination of nitrogen, oxygen and metallic and oxidic constituents (ISO 21068‑3:2024)
SIST EN ISO 21068-3:2024

This document specifies analytical techniques for the determination of total nitrogen and nitrogen calculated as silicon nitride, total oxygen, and metallic and oxidic components in silicon carbide raw materials and refractory products.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21068-4:2024(Main)
Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 4: XRD methods (ISO 21068‑4:2024)
SIST EN ISO 21068-4:2024

This document describes methods for the determination of mineralogical phases typically apparent in nitride and oxy-nitride bonded silicon carbide refractory products using a Bragg-Brentano diffractometer.
It includes details of sample preparations and general principles for qualitative and quantitative analyses of mineralogical phase composition. Quantitative determination of α-Si3N4, β-Si3N4, Si2ON2, AlN, and β’- SiAlON are described.
For quantitative determination of α-Si3N4, β-Si3N4, Si2ON2, AlN and β’-SiAlON refinement procedures based on the total nitrogen content of the sample are described.
NOTE            ISO 21068-3 is used for the analysis of the total nitrogen content of the sample.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8840:2024(Main)
Refractory materials - Determination of bulk density of granular materials (grain density) (ISO 8840:2021)
SIST EN ISO 8840:2024

This document specifies three methods for the determination of the bulk density of granular refractory materials (grain density) having a grain size larger than 2 mm:
—    Method 1: mercury method with vacuum;
—    Method 2: arrested water absorption method;
—    Method 3: vacuum method with spin dryer option according to ISO 5017.
Method 1 is intended as the reference method.
NOTE       Depending on the nature of the material tested, the three methods can give different results. Any statement of the value of a bulk density can therefore be accompanied by an indication of the method used or to be used in case of dispute.
The same method can be used for the determination of the volume of the sample, for selecting and preparing the sample, for calculating the bulk density and for presenting the test report.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21068-1:2024(Main)
Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 1: General information, terminology and sample preparation (ISO 21068-1:2024)
SIST EN ISO 21068-1:2024

This document gives definitions and specifies techniques for the preparation of samples for the chemical analysis of silicon-carbide-containing raw materials and refractory products including:
a)       SiC raw materials;
b)       graphite brick containing silicon carbide;
c)        silicon carbide brick (includes the bricks containing silicon nitride, silicon oxynitride, sialon);
d)       refractories containing carbon and/or silicon carbide mixed with clay;
e)       refractories containing carbon and/or silicon carbide mixed with silica (and fused silica);
f)         refractories containing carbon and/or silicon carbide mixed with high alumina material;
g)       refractories containing carbon and/or silicon carbide mixed with magnesia (and dolomite);
h)       refractories containing carbon and/or silicon carbide mixed with chrome mineral or magnesia-chrome materials;
i)         refractories containing carbon and/or silicon carbide except those described in a) to h) above.
The items of analysis described in ISO 21068-2, ISO 21068-3 and ISO 21068-4 are as follows:
—     loss on drying (LOD);
—     loss on ignition (LOI);
—     total carbon, Ctotal;
—     free carbon, Cfree;
—     silicon carbide, SiC;
—     free silicon (Sifree);
—     free aluminium (Alfree);
—     free magnesium (Mgfree);
—     free iron (Fefree);
—     silicon(IV) dioxide (SiO2);
—     aluminium(III) oxide (Al2O3);
—     iron(III) oxide (Fe2O3);
—     titanium(IV) oxide (TiO2);
—     calcium oxide (CaO);
—     magnesium oxide (MgO);
—     sodium oxide (Na2O);
—     potassium oxide (K2O);
—     chromium(III) oxide (Cr2O3);
—     zirconium(IV) oxide (ZrO2);
—     boron oxide (total boron calculated as B2O3);
—     nitrogen;
—     oxygen;
—     nitrides (undifferentiated: Si3N4, AlN, BN, sialon, oxy-nitrides, etc.);
—     mineralogical phases (XRD-methods).

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 993-10:2020(Main)
Methods of test for dense shaped refractory products - Part 10: Determination of permanent change in dimensions on heating
SIST EN 993-10:2020

This document specifies three methods for the determination of the permanent change in dimensions on heating of dense shaped refractory products.
NOTE   The methods can be applied to materials sensitive to oxidation. However, some of these materials can be affected during the test in such a way as to make the measurement of the dimensional changes impossible to carry out to the required accuracy.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 993-5:2018(Main)
Methods of test for dense shaped refractory products - Part 5: Determination of cold crushing strength
SIST EN 993-5:2019

This document specifies a method of determination of the cold crushing strength of dense shaped refractory products.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 993-6:2018(Main)
Methods of test for (dense) shaped refractory products - Part 6: Determination of modulus of rupture at ambient temperature
SIST EN 993-6:2019

This Part of EN 993 specifies a method for the determination of the modulus of rupture of dense and insulating shaped refractory products at ambient temperature, under conditions of a constant rate of increase of stress.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    14 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 993-1:2018(Main)
Methods of test for dense shaped refractory products - Part 1: Determination of bulk density, apparent porosity and true porosity
SIST EN 993-1:2019

This document specifies a method for the determination of the bulk density, apparent porosity and true porosity of dense shaped refractory products.
NOTE   For shaped insulating refractory products, the bulk density and true porosity are determined in accordance with EN 1094-4.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day