EN ISO 18403:2016

Footwear - Test methods for slide fasteners - Resistance to damage during closure under a lateral force (ISO 18403:2016)

ISO 18403:2016 specifies a test method intended to determine the maximum lateral force applied to a slide fastener for footwear under which it will close without failure. The method is applicable to all types of slide fastener.

Schuhe - Prüfverfahren für Reißverschlüsse - Widerstand gegen Beschädigung während des Schließens mit einer Lateralkraft (ISO 18403:2016)

Diese Norm legt ein Prüfverfahren zur Bestimmung der auf einen Reißverschluss für Schuhe aufgebrachten maximalen lateralen Kraft fest, bei der der Reißverschluss ohne Versagen geschlossen werden kann. Das Verfahren gilt für sämtliche Arten von Reißverschlüssen.

Chaussures - Méthodes d'essai des fermetures à glissière - Résistance à l'endommagement en cas de fermeture avec application d'une force de traction latérale (ISO 18403:2016)

ISO 18403:2016 spécifie une méthode d'essai destinée à déterminer la force latérale maximale, appliquée à une fermeture à glissière de chaussure, à laquelle la fermeture se fermera sans défaillance. Cette méthode s'applique à tous les types de fermetures à glissière.

Obutev - Preskusne metode za zadrge - Odpornost proti poškodbam med zapiranjem pri delovanju stranske sile (ISO 18403:2016)

Ta standard določa preskusno metodo za določanje največje stranske sile na zadrgo pri obutvi, pri kateri se bo zadrga zaprla brez okvare.  Ta metoda se uporablja se za vse vrste zadrg.

General Information

• Status: Published
• Publication Date: 17-May-2016
• Withdrawal Date: 29-Nov-2016
• ICS: 61.040 - Headgear. Clothing accessories. Fastening of clothing
• ICS: 61.060 - Footwear
• Technical Committee: CEN/TC 309 - Footwear
• Drafting Committee: CEN/TC 309/WG 1 - Minimum performance requirements and test methods for components for footwear
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 18-May-2016
• Due Date: 06-Nov-2014
• Completion Date: 18-May-2016
• Ref Project: SIST EN ISO 18403:2016 - Footwear - Test methods for slide fasteners - Resistance to damage during closure under a lateral force (ISO 18403:2016)

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2016
Obutev - Preskusne metode za zadrge - Odpornost proti poškodbam med
zapiranjem pri delovanju stranske sile (ISO 18403:2016)
Footwear - Test methods for slide fasteners - Resistance to damage during closure
under a lateral force (ISO 18403:2016)
Schuhe - Prüfverfahren für Reißverschlüsse - Widerstand gegen Beschädigung während
des Schließens mit einer Lateralkraft (ISO 18403:2016)
Chaussures - Méthodes d'essai pour les fermetures éclair - Résistance aux dommages
durant la fermeture avec une force latérale (ISO 18403:2016)
Ta slovenski standard je istoveten z: EN ISO 18403:2016
ICS:
61.040 3RNULYDOD'RGDWNLN Headgear. Clothing
REODþLORP6SHQMDQMHREODþLO accessories. Fastening of
clothing
61.060 Obuvala Footwear
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 18403
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2016
EUROPÄISCHE NORM
ICS 61.060
English Version
Footwear - Test methods for slide fasteners - Resistance to
damage during closure under a lateral force (ISO
18403:2016)
Chaussures - Méthodes d'essai des fermetures à Schuhe - Prüfverfahren für Reißverschlüsse -
glissière - Résistance à l'endommagement en cas de Widerstand gegen Beschädigung während des
fermeture avec application d'une force de traction Schließens mit einer Lateralkraft (ISO 18403:2016)
latérale (ISO 18403:2016)
This European Standard was approved by CEN on 15 April 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18403:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 18403:2016) has been prepared by Technical Committee ISO/TC 216
“Footwear” in collaboration with Technical Committee CEN/TC 309 “Footwear” the secretariat of which
is held by AENOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2016, and conflicting national standards
shall be withdrawn at the latest by November 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18403:2016 has been approved by CEN as EN ISO 18403:2016 without any modification.

INTERNATIONAL ISO
STANDARD 18403
First edition
2016-05-01
Footwear — Test methods for slide
fasteners — Resistance to damage
during closure under a lateral force
Chaussures — Méthodes d’essai des fermetures à glissière —
Résistance à l’endommagement en cas de fermeture avec application
d’une force de traction latérale
Reference number
ISO 18403:2016(E)
©
ISO 2016
ISO 18403:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 18403:2016(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 3
5 Apparatus and materials. 3
6 Test specimens. 4
7 Procedure. 4
8 Test report . 5
ISO 18403:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any pat
...