61.040 - Headgear. Clothing accessories. Fastening of clothing

ISO 10750:2015 describes a method intended to determine the attachment strength of the top and bottom stops of a slide fastener. The method is applicable to all types of slide fastener for footwear.

ISO 10750:2015 describes a method intended to determine the attachment strength of the top and bottom stops of a slide fastener. The method is applicable to all types of slide fastener for footwear.

This standard describes a method intended to assess the lateral strength of a closed slide fastener for footwear.  The method is applicable to all types of slide fastener.

This standard specifies a test method intended to determine the maximum lateral force applied to a slide fastener for footwear under which it will close without failure.  The method is applicable to all types of slide fastener.

This standard specifies a test method intended to assess the strength of slide fastener pullers for footwear.  The method is applicable to all types of footwear slide fastener.

This standard describes a method intended to determine the resistance of a slide fastener to repeated opening and closing.  The method is applicable to all types of slide fastener with a chain length greater than 80 mm

ISO 18403:2016 specifies a test method intended to determine the maximum lateral force applied to a slide fastener for footwear under which it will close without failure. The method is applicable to all types of slide fastener.

ISO 10734:2016 specifies a test method intended to assess the strength of slide fastener pullers for footwear. The method is applicable to all types of footwear slide fastener.

ISO 10751:2016 describes a method intended to determine the resistance of a slide fastener to repeated opening and closing. The method is applicable to all types of slide fastener with a teeth length greater than 80 mm.

ISO 10764:2016 describes a method intended to assess the lateral strength of a closed slide fastener for footwear. The method is applicable to all types of slide fastener.

This European Standard specifies performance levels and test methods for the following characteristics
of slide fasteners made from interlocking components mounted on tapes: strengths of puller
attachment, closed-end, top stop, open-end slide fastener box, reciprocating mechanism, closed slide
fastener when extended laterally, open-end attachment when extended laterally, slider locking device,
and open-end slide fastener single stringer slider retention and slider resistance to torque.
NOTE...view more

This European Standard specifies performance levels and test methods for the following characteristics of slide fasteners made from interlocking components mounted on tapes: strengths of puller attachment, closed-end, top stop, open-end slide fastener box, reciprocating mechanism, closed slide fastener when extended laterally, open-end attachment when extended laterally, slider locking device, and open-end slide fastener single stringer slider retention and slider resistance to torque.
NOTE    Th...view more

This European Standard describes a standard method for determining the PM10 or PM2,5 mass concentrations of suspended particulate matter in ambient air by sampling the particulate matter on filters and weighing them by means of a balance.
Measurements are performed with samplers with inlet designs as specified in Annex A, operating at a nominal flow rate of 2,3 m3/h, over a nominal sampling period of 24 h. Measurement results are expressed in µg/m3, where the volume of air is the volume at ambi...view more

This test method is intended to determine the locking strength of a slide fastener slider for footwear.  The method is applicable to all types of slide fastener that have a slider locking device.

This method is intended to assess the burst strength of a closed slide fastener for footwear.  The method is applicable to all types of slide fastener.

ISO 10748:2011 specifies a test method to determine the locking strength of a slide fastener slider for footwear. The method is applicable to all types of slide fastener that have a slider locking device.

ISO 10717:2010 specifies a test method intended to assess the burst strength of a closed slide fastener for footwear. The method is applicable to all types of slide fastener.

ISO 10765:2010 specifies a test method for the determination of some typical parameters of elastics for footwear using the strength/elongation graph, which is obtained from the tensile strength test. This method is applicable to any elastic material used for footwear.

This European Standard specifies a method for determining the resistance to fraying of touch and close fasteners.

This European Standard specifies a method for determining the resistance to fraying of touch and close fasteners.