EN 13126-16:2019

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 16: Hardware for Lift and Slide windows

This part of EN 13126 specifies requirements and test methods for durability, strength, security and function of hardware for Lift and Slide windows and door height windows in accordance with common application as shown in informative Annex C, regardless of whether the hardware enables an additional tilt position.
NOTE 1   This document is also applicable to hardware systems, whereby the sash itself is not lifted but a gasket mechanism is moved.
NOTE 2   This document is also applicable to hardware systems, whereby the sash itself is not lifted but the sash is being moved parallel to the plane of the frame.

Baubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und Prüfverfahren - Teil 16: Beschläge für Hebeschiebe-Fenster und -Fenstertüren

Dieses Dokument legt die Anforderungen und Prüfverfahren für die Dauerfunktionsfähigkeit, Festigkeit, Schutzwirkung und Funktionsweise von Beschlägen für Hebeschiebe Fenster und  Fenstertüren entsprechend der in Bild C.1 und Bild C.2 im informativen Anhang C dargestellten üblichen Anwendung fest, unabhängig davon, ob die Beschläge eine zusätzliche Kippstellung ermöglichen.
ANMERKUNG 1   Dieses Dokument gilt auch für Beschlagsysteme, bei denen der Fensterflügel selbst nicht gehoben, sondern ein Dichtungsmechanismus bewegt wird.
ANMERKUNG 2   Dieses Dokument gilt auch für Beschlagsysteme, bei denen der Fensterflügel selbst nicht gehoben, sondern parallel zur Rahmenebene bewegt wird.

Quincaillerie pour le bâtiment - Ferrures de fenêtres et portes-fenêtres - Exigences et méthodes d'essai - Partie 16 : Ferrures pour fenêtres coulissantes à levage

Le présent document spécifie les exigences et les méthodes d’essai relatives à l'endurance, la résistance, la sécurité et le fonctionnement des ferrures pour portes-fenêtres et fenêtres coulissantes à levage, en conformité avec l’application courante représentée dans les Figures C.1 et C.2 de l’Annexe C, informative, indépendamment du fait que ces ferrures permettent une inclinaison supplémentaire.
NOTE 1   Le présent document est également applicable aux systèmes de ferrures où le vantail lui-même n'est pas soulevé mais un mécanisme de joint est déplacé.
NOTE 2   Le présent document est également applicable aux systèmes de ferrures où le vantail lui-même n'est pas soulevé, mais est déplacé parallèlement au plan du cadre.

Stavbno okovje - Okovje za okna in zastekljena vrata - Zahteve in preskusne metode - 16. del: Okovje za dvižno-drsna okna in vrata

Ta standard EN 13126 določa zahteve in preskusne postopke za trajnost, trdnost, varnost in delovanje okovja za dvižno-drsna okna in zastekljena vrata v skladu z običajno uporabo, kot je opisana v informativnem dodatku C, ne glede na to, ali okovje omogoča dodatni položaj nagibanja ali ne.

General Information

• Status: Published
• Publication Date: 16-Apr-2019
• Withdrawal Date: 30-Oct-2019
• ICS: 91.190 - Building accessories
• Technical Committee: CEN/TC 33 - Doors, windows, shutters and building hardware
• Drafting Committee: CEN/TC 33/WG 4 - Building hardware
• Current Stage: 9060 - Closure of 2 Year Review Enquiry - Review Enquiry
• Start Date: 02-Dec-2024
• Completion Date: 02-Dec-2024
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Ref Project: SIST EN 13126-16:2019 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 16: Hardware for Lift and Slide windows

Relations

• Replaces: EN 13126-16:2008 - Building hardware - Requirements and test methods for windows and doors height windows - Part 16: Hardware for Lift&Slide windows and doors
• Effective Date: 24-Apr-2019
• Corrected By: EN 13126-16:2019/AC:2022 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 16: Hardware for Lift and Slide windows
• Effective Date: 04-May-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2019
Nadomešča:
SIST EN 13126-16:2008
Stavbno okovje - Okovje za okna in zastekljena vrata - Zahteve in preskusne
metode - 16. del: Okovje za dvižno-drsna okna in vrata
Building hardware - Hardware for windows and door height windows - Requirements and
test methods - Part 16: Hardware for Lift and Slide windows
Baubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und
Prüfverfahren - Teil 16: Beschläge für Hebeschiebe-Fenster und -Fenstertüren
Quincaillerie pour le bâtiment - Ferrures de fenêtres et portes-fenêtres - Exigences et
méthodes d'essai - Partie 16 : Ferrures pour fenêtres coulissantes à levage
Ta slovenski standard je istoveten z: EN 13126-16:2019
ICS:
91.190 Stavbna oprema Building accessories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13126-16
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2019
EUROPÄISCHE NORM
ICS 91.190 Supersedes EN 13126-16:2008
English Version
Building hardware - Hardware for windows and door
height windows - Requirements and test methods - Part
16: Hardware for Lift and Slide windows
Quincaillerie pour le bâtiment - Ferrures de fenêtres et Baubeschläge - Beschläge für Fenster und Fenstertüren
portes-fenêtres - Exigences et méthodes d'essai - Partie - Anforderungen und Prüfverfahren - Teil 16:
16 : Ferrures pour fenêtres coulissantes à levage Beschläge für Hebeschiebe-Fenster und -Fenstertüren
This European Standard was approved by CEN on 8 March 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13126-16:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Classification . 9
4.1 General . 9
4.2 Durability (1 – first box) . 9
4.3 Mass (2 – second box) . 9
4.4 Corrosion resistance (3 – third box) . 10
4.5 Test sizes (4 – fourth box) . 10
4.6 Example of classification . 10
5 Requirements . 11
5.1 Dangerous substances . 11
5.2 Additional requirements . 11
5.2.1 Handle operation tolerance . 11
5.2.2 Sliding operation crash-tests . 12
5.2.3 Minimum closing device resistance . 12
5.2.4 Resistance to additional loading . 13
5.2.5 Static endurance test at ambient temperature . 13
5.3 Durability . 13
5.4 Corrosion resistance . 13
6 Test equipment and preparation for the test . 14
6.1 Test rig . 14
6.2 Specimen . 14
6.3 Mounting of specimen . 15
7 Test procedure . 15
7.1 Samples . 15
7.2 Procedure. 15
7.2.1 Genreal . 15
7.2.2 Adjusting the test mass . 16
7.2.3 Lubrication and adjustment of hardware . 16
7.3 Durability test. 16
7.3.1 Description of the cycles . 16
7.3.2 Acceptance criteria . 19
7.4 Sliding operation crash-tests . 19
7.4.1 Procedure – into the closed position . 19
7.4.2 Procedure – into the opening position . 19
7.4.3 Acceptance criteria . 20
7.5 Minimum closing device resistance test . 20
7.5.1 Hardware with tilt function . 20
7.5.2 Hardware with tilt-function with positive control . 20
7.6 Additional loading test . 21
7.6.1 Procedure. 21
7.6.2 Acceptance criteria . 21
7.7 Static endurance test at ambient temperature . 21
7.8 Corrosion resistance. 21
8 Marking . 21
Annex A (informative) Test assembly . 23
Annex B (informative) Flow chart of test procedures . 28
Annex C (informative) Window types . 29
Bibliography . 30
European foreword
This document (EN 13126-16:2019) has been prepared by Technical Committee CEN/TC 33 “Doors,
windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2019, and conflicting national standards shall
be withdrawn at the latest by October 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13126-16:2008.
With regard to EN 13126-16:2008, the following significant changes were made:
— EN 13126-16 now is independent from EN 13126-1; all necessary information is included without
the need of any further information from EN 13126-1;
— several editorial changes in the wording for a better understanding;
— new terms and definitions added under 3.13 - 3.18;
— under 4.1 classification system changed completely; former digits 1 (Category of use), 4 (Fire
resistance), 5 (Safety in use), 7 (Security) and 8 (Applicable part) deleted; former digit 2 changed
into box 1 (Durability), former digit 3 changed into box 2 (Mass), former digit 6 changed into box 3
(Corrosion resistance) and former digit 9 changed into box 4 (Test sizes);
— under 4.2 new grades for the number of cycles defined; H1 (5 000), H2 (10 000) and H3 (20 000);
— under 4.5 test size changed from SW (sash width) 1 200 mm and SH (=sash height) 2 000 mm into
new sizes SW (sash width) 1 440 mm and SH (=sash height) 2 400 mm;
— under 4.6 new example of classification added in accordance with the new classification system; 2
alternative ways (table or alphanumerical) to show the classification defined;
— under Clause 6 “Test equipment and preparation for the test” additional information added for the
test rig (6.1), the specimen (6.2) and the mounting of the specimen (6.3);
— under 6.2 “Specimen” the use of gaskets added in the description;
— under 7.2 “Procedure” new subclause 7.2.1 “General”, 7.2.2 ”Adjusting the test mass” and 7.2.3
”Lubrication and adjustment of hardware” added with additional information, mainly from the
current version of part 1;
— under 7.3 “Durability test” procedure modified to ensure better correlation with the test procedure
described in EN 1191:2012;
— under 8 new clause added regarding marking with information from the current version of
EN 13126-1.
This European standard is one of a series of European standards for building hardware products for
windows and door height windows. This European standard is independent of EN 13126-1.
EN 13126 consists of the following parts:
— Building hardware — Hardware for windows and door height windows — Requirements and test
methods — Part 1: Requirements common to all types of hardware;
— Building hardware — Requirements and test methods for windows and doors height windows — Part
2: Window fastener handles;
— Building hardware — Hardware for windows and door-height windows — Requirements and test
methods — Part 3: Handles, primarily for Tilt&Turn, Ti
...