FprEN 17449

Safety of machinery - Safety requirements to finishing lines for metal strip

This document specifies the general safety requirements for finishing lines for metal strip, hereafter referred as finishing line(s), as defined in 3.1.
This document deals with significant hazards, hazardous situations and events relevant for finishing lines when used as intended and under conditions foreseen by the manufacturer. This document provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, operation and de-commissioning, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment (see Clauses 4 and 5).
This document is applicable to:
Plant (machinery, equipment, devices) for the customer-specific processing of metal strip/metal foil (starting material: hot rolled or cold rolled strip as coil) from the material feeding (1) via the finishing process (2) until the material removal (3) (see exemplary layout in Figure 1).
Figure 1...
Examples of finishing lines and their machinery/equipment covered by the scope of this standard are listed below:
-   finishing lines, e.g.:
-   slitting line (see Figure 2);
-   cut-to-length line (see Figure 3);
-   feeding line (see Figure 4);
-   blanking line;
-   trimming line;
-   rounding machines;
-   strip edge machining lines;
-   inspection lines;
-   rewinding lines, separator lines, doubler lines;
-   strip-supply lines (e.g. for presses or roll forming lines);
-   interlinked machinery/equipment which can be part of a finishing line, e.g.:
-   coil conveying (e.g. feeding in, threading, pushing-in, guiding and transporting);
-   stretching, bending, levelling machine;
-   marking machine;
-   recoiler and uncoiler;
-   shears;
-   punching machine;
-   coil and sleeve handling device;
-   welding machine;
-   oiling machine;
-   scrap chopper, scrap coiler, scrap conveyor;
-   changing device;
-   stacking device;
-   coil transport device (associated with the line);
-   measuring systems and devices;
-   fluid systems.
The following machinery may be part of or linked to a finishing line but are not covered by this document:
-   packaging lines (EN 415);
-   roll forming lines;
-   machines for painting and laminating;
-   embossing machine;
-   saws;
-   plate shear (plate as raw material) (EN 13985);
-   equipment for applying (removing) media to (from) the material surface;
-   coil transport devices outside the boundaries of the line (e.g. supply from the storage);
-   presses (EN 692 and EN 693);
-   milling machines (EN 13128);
-   machinery using laser (EN ISO 11553) for strip processing (e.g. welding, cutting);
-   punching machines (as stand-alone machine);
-   cranes;
-   robots (EN ISO 10218);
-   separate media systems (e.g. compressed air system, exhaust system);
-   storage equipment.
For modernization, this document can be applied for the parts to be modernized.
Figure 2, 3, 4...

Sicherheit von Maschinen - Sicherheitsanforderungen an Adjustageanlagen für Metallband

Diese Europäische Norm spezifiziert die allgemeinen Sicherheitsanforderungen für Adjustageanlagen für Metallband oder -folie, nachfolgend Adjustageanlage(n) genannt, wie in 3.1 definiert.
Dieses Dokument behandelt die für Adjustageanlagen zutreffenden signifikanten Gefährdungen, Gefährdungs¬situationen und -ereignisse.
Dieses Dokument legt die Anforderungen fest, die der Hersteller erfüllen muss, um die Sicherheit von Personen und Gütern während des Transports, der Inbetriebnahme, des Betriebs und der Außerbetriebnahme sowie bei vorhersehbaren Ausfällen oder Fehlfunktionen, die an den Geräten auftreten können, zu gewährleisten (siehe Kapitel 4 und 5).
Diese Norm gilt für:
Anlagen (Maschinen, Ausrüstungen, Einrichtungen) zur kundenspezifischen Bearbeitung von Metallband/-folie (Aus¬gangsmaterial: Warm- oder Kaltband als Coil) von der Materialzufuhr (1) über den Adjustageprozess (2) bis zur Materialabfuhr (3) (siehe beispielhaftes Layout in Bild 1).
[...]

Sécurité des machines - Prescriptions de sécurité pour les lignes de finition pour bandes métalliques

Le présent document spécifie les prescriptions générales de sécurité pour les lignes de finition pour bandes métalliques, ci-après désignées par le terme « ligne(s) de finition », telles que définies en 3.1.
Le présent document traite des phénomènes, situations et événements dangereux significatifs et propres aux lignes de finition lorsqu'elles sont utilisées normalement et dans les conditions prévues par le fabricant. Le présent document fournit les exigences que doit respecter le fabricant pour assurer la sécurité des personnes et des biens pendant le transport, la mise en service, l'exploitation et la mise hors service, ainsi qu'en cas de défaillances ou de dysfonctionnements prévisibles qui peuvent survenir sur l'équipement (voir Articles 4 et 5).
Le présent document s'applique aux :
Installations (machines, équipements, dispositifs) destinés au traitement spécifique au client de bandes/feuilles métalliques (matière de départ : bande laminée à chaud ou à froid sous forme de bobine) depuis l'alimentation en matière (1) en passant par le processus de finition (2) jusqu'à l'enlèvement de matière (3) (voir exemple de disposition à la Figure 1).
Des exemples de lignes de finition et de leurs machines/équipements couverts par le domaine d'application du présent document sont énumérés ci-dessous :
— lignes de finition, par exemple :
— ligne de refendage (voir Figure 2) ;
— ligne de cisaillage (voir Figure 3) ;
— ligne d'alimentation (voir Figure 4) ;
— ligne de découpage des flans ;
— ligne d'ébarbage ;
— arrondisseuses ;
— ligne d'usinage des bords de bande ;
— lignes d'inspection ;
— lignes de rebobinage, lignes de séparation, lignes de doublage ;
— lignes d'alimentation de bandes (par exemple pour les presses ou les lignes de formage par laminage) ;
— machines interconnectées/équipements interconnectés pouvant faire partie d'une ligne de finition, par exemple :
— convoyage de bobines (par exemple, approvisionnement, alimentation, engagement, guidage et transport) ;
— machine à étirer, à courber, machine de nivellement ;
— machine de marquage ;
— rebobineuse et dérouleuse ;
— machine à sectionner ;
— poinçonneuse ;
— dispositif de manutention de bobine et manchon ;
— machine de soudage ;
— machine à lubrifier ;
— mitrailleuse, enrouleuse de ferraille, convoyeur de ferraille ;
— dispositif de remplacement ;
— dispositif d'empilement ;
— dispositif de transport de bobines (associé avec la ligne) ;
— systèmes et dispositifs de mesurage ;
— systèmes pour fluides.
Les machines suivantes peuvent faire partie ou être associées à une ligne de finition mais ne sont pas couvertes par le présent document :
— lignes d'emballage (EN 415) ;
— lignes de formage par laminage ;
— machines à peindre et à laminer ;
— machine à gaufrer ;
— scies ;
— cisailles à tôles (tôle en tant que matière première) (EN 13985) ;
— équipement pour l'application (l'enlèvement) de fluides sur (de) la surface du matériau ;
— dispositifs de transport de bobines situés en dehors des limites de la ligne (par exemple, approvisionnement depuis le stockage) ;
— presses (EN 692 et EN 693) ;
— fraiseuses (EN 13128) ;
— machines utilisant le laser (EN ISO 11553) pour le traitement des bandes (par exemple, soudage, découpage) ;
— poinçonneuses (en tant que machine autonome) ;
— grues ;
— robots (EN ISO 10218) ;
— systèmes de fluides séparés (par exemple, système d'air comprimé, système d'extraction) ;
— équipements de stockage.
Pour la modernisation, ce document peut être appliqué pour les parties à moderniser.

Varnost strojev - Varnostne zahteve za zaključne črte na kovinskem traku

General Information

• Status: Not Published
• ICS: 77.180 - Equipment for the metallurgical industry
• Technical Committee: CEN/TC 322 - Equipments for making and shaping of metals - Safety requirements
• Drafting Committee: CEN/TC 322/WG 3 - Rolling mills and finishing line equipment
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Due Date: 25-Nov-2021
• Completion Date: 25-Nov-2021
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: kSIST FprEN 17449:2020 - Safety of machinery - Safety requirements to finishing lines for metal strip

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN 17449:2020
01-april-2020
Varnost strojev - Varnostne zahteve za zaključne črte na kovinskem traku
Safety of machinery - Safety requirements to finishing lines for metal strip
Sicherheit von Maschinen - Sicherheitsanforderungen an Adjustageanlagen für
Metallband

Sécurité des machines - Prescriptions de sécurité pour les lignes de finition pour bandes

métalliques
Ta slovenski standard je istoveten z: prEN 17449
ICS:
13.110 Varnost strojev Safety of machinery
77.180 Oprema za metalurško Equipment for the
industrijo metallurgical industry
oSIST prEN 17449:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17449:2020
---------------------- Page: 2 ----------------------
oSIST prEN 17449:2020
DRAFT
EUROPEAN STANDARD
prEN 17449
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2020
ICS 77.180
English Version
Safety of machinery - Safety requirements to finishing
lines for metal strip

Sécurité des machines - Prescriptions de sécurité pour Sicherheit von Maschinen - Sicherheitsanforderungen

les lignes de finition pour bandes métalliques an Adjustageanlagen für Metallband

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee

CEN/TC 322.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17449:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
Contents Page

European foreword ....................................................................................................................................................... 4

Introduction .................................................................................................................................................................... 5

1 Scope .................................................................................................................................................................... 6

2 Normative references ................................................................................................................................. 10

3 Terms and definitions ................................................................................................................................ 13

4 Significant hazards and risk assessment ............................................................................................. 19

4.1 General ............................................................................................................................................................. 19

4.2 Interfaces to the linked/integrated equipment ................................................................................ 19

5 Safety requirements and/or protective/risk-reduction measures ........................................... 19

5.1 General ............................................................................................................................................................. 19

5.2 General requirements for design, planning and risk assessment .............................................. 20

5.3 List of significant hazards, hazardous situations, safety requirements and/or

protective/risk-reduction measures .................................................................................................... 38

6 Verification/validation of safety requirements/functions and/or protective/risk

reduction measures .................................................................................................................................... 66

6.1 General ............................................................................................................................................................. 66

6.2 Required verification D .............................................................................................................................. 66

6.3 Required verification V, M and T ............................................................................................................ 67

7 Information for use ..................................................................................................................................... 68

7.1 General ............................................................................................................................................................. 68

7.2 Warning devices and safety signs .......................................................................................................... 68

7.3 Minimum marking ....................................................................................................................................... 68

7.4 Accompanying documents ........................................................................................................................ 68

7.5 Training of personnel ................................................................................................................................. 71

8 Supplementary information regarding repair work ....................................................................... 72

Annex A (normative) Requirements for shut-down, emergency stop and other stop

functions .......................................................................................................................................................... 73

Annex B (normative) Noise test code ................................................................................................................. 78

Annex C (normative) Protection of persons in case of using asphyxiant gases used in

firefighting systems ..................................................................................................................................... 83

Annex D (informative) Example for operating modes in relation to segregated areas ................... 87

Annex E (informative) Example for the risk analysis due to interfaces ................................................ 88

Annex ZA (informative) Relationship between this European Standard and the essential

requirements of Directive 2006/42/EC aimed to be covered ..................................................... 89

Bibliography ................................................................................................................................................................. 93

---------------------- Page: 4 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
Figures

Figure 1 — Exemplary layout of a finishing line for metal strip ...................................................................................6

Figure 2 — Exemplary layout of a slitting line .....................................................................................................................8

Figure 3 — Exemplary layout of a cut-to-length line .........................................................................................................9

Figure 4 — Exemplary layout of a feeding line .....................................................................................................................9

Figure 5 — Schematic representation of the life phases of a finishing line ........................................................... 20

Figure D.1 — Schematic diagram of operating modes in relation to segregated areas .................................... 87

Figure E.1 — Diagram of a hypothetical line indicating potentially hazardous interfaces ............................. 88

Tables

Table 1 — Characteristic tasks and conditions for exemplary operating modes ............................................... 23

Table 2 — Hazards and corresponding risk parameters for the determination of PLr ................................... 30

Table 3 — Main noise sources of finishing line equipment and exemplary noise reduction measures

............................................................................................................................................................................................. 37

Table 4 — Significant hazards, hazardous situations, safety requirements and/or measures ..................... 39

Table A.1 — Shut-down functions .......................................................................................................................................... 74

Table A.2 — Emergency stop and stop functions ............................................................................................................. 76

Table B.1 — Example of declared dual-number noise emission values for work stations ............................. 82

Table ZA.1 — Correspondence between this European Standard and Annex I of

Directive 2006/42/EC ............................................................................................................................................... 89

---------------------- Page: 5 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
European foreword

This document (prEN 17449:2019) has been prepared by Technical Committee CEN/TC 322 “Equipment

for making and shaping of metals”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.

This document has been prepared under a mandate given to CEN by the European Commission and the

European Free Trade Association and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this

document.
---------------------- Page: 6 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
Introduction
This European Standard is a type C standard as stated in EN ISO 12100:2010.

This document is not applicable to finishing lines for metal strip (according to the scope) manufactured

before the date of its publication.

The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are

covered are indicated in the Scope of this document.

Where for clarity an example of a preventative measure is given, this should not be considered as the only

possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent

level of safety is achieved.

When requirements of this type-C standard are different from those which are stated in type-A or -B

standards, the requirements of this type-C standard take precedence over the requirements of the other

standards for machines that have been designed and built according to the requirements of this type-C

standard.

This document is of relevance, in particular, for the following stakeholder groups representing the market

players with regard to machinery safety:
— machine and/or plant manufacturers (small, medium and large enterprises);

— health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).

Others can be affected by the level of machinery safety achieved with the means of the document by the

above-mentioned stakeholder groups:
— machine and/or plant users/employers (small, medium and large enterprises);
— service providers, e.g. for maintenance (small, medium and large enterprises).

The above-mentioned stakeholder groups have been given the possibility to participate at the drafting

process of this document.
---------------------- Page: 7 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
1 Scope

This document specifies the general safety requirements for finishing lines for metal strip, hereafter

referred as finishing line(s), as defined in 3.1.

This document deals with significant hazards, hazardous situations and events relevant for finishing lines

when used as intended and under conditions foreseen by the manufacturer. This document provides the

requirements to be met by the manufacturer to ensure the safety of persons and property during

transport, commissioning, operation and de-commissioning, as well as in the event of foreseeable failures

or malfunctions that can occur in the equipment (see Clauses 4 and 5).
This document is applicable to:

Plant (machinery, equipment, devices) for the customer-specific processing of metal strip/metal foil

(starting material: hot rolled or cold rolled strip as coil) from the material feeding (1) via the finishing

process (2) until the material removal (3) (see exemplary layout in Figure 1).
Key
1 supply or removal of material (as coil) or tools (e.g. spool/sleeve)

2 finishing process (e.g. cutting, trimming, punching, straightening, laminating, inspecting, rewinding)

3 removal or supply of material (e.g. as coil, slit strip, stack) respectively pallet feed

4 changing devices (e.g. levelling rolls, knife shaft, cutting tools)
5 border of the finishing line
Figure 1 — Exemplary layout of a finishing line for metal strip

Examples of finishing lines and their machinery/equipment covered by the scope of this standard are

listed below:
— finishing lines, e.g.:
— slitting line (see Figure 2);
— cut-to-length line (see Figure 3);
— feeding line (see Figure 4);
— blanking line;
— trimming line;
---------------------- Page: 8 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
— rounding machines;
— strip edge machining lines;
— inspection lines;
— rewinding lines, separator lines, doubler lines;
— strip-supply lines (e.g. for presses or roll forming lines);
— interlinked machinery/equipment which can be part of a finishing line, e.g.:

— coil conveying (e.g. feeding in, threading, pushing-in, guiding and transporting);

— stretching, bending, levelling machine;
— marking machine;
— recoiler and uncoiler;
— shears;
— punching machine;
— coil and sleeve handling device;
— welding machine;
— oiling machine;
— scrap chopper, scrap coiler, scrap conveyor;
— changing device;
— stacking device;
— coil transport device (associated with the line);
— measuring systems and devices;
— fluid systems.

The following machinery may be part of or linked to a finishing line but are not covered by this document:

— packaging lines (EN 415);
— roll forming lines;
— machines for painting and laminating;
— embossing machine;
— saws;
— plate shear (plate as raw material) (EN 13985);
---------------------- Page: 9 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
— equipment for applying (removing) media to (from) the material surface;

— coil transport devices outside the boundaries of the line (e.g. supply from the storage);

— presses (EN 692 and EN 693);
— milling machines (EN 13128);

— machinery using laser (EN ISO 11553) for strip processing (e.g. welding, cutting);

— punching machines (as stand-alone machine);
— cranes;
— robots (EN ISO 10218);
— separate media systems (e.g. compressed air system, exhaust system);
— storage equipment.
For modernization, this document can be applied for the parts to be modernized.
Key
1 uncoiler 5 recoiler
2 peeler 6 coil car
3 circular knife cutter 7 knife changing device
4 loop 8 coil car
Figure 2 — Exemplary layout of a slitting line
---------------------- Page: 10 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
Key
1 uncoiler 7 feeder
2 peeler 8 shear (covered by the scope) or
3 shear press, laser (not covered by the scope)
4 scrap box 9 stacker
5 straightener 10 coil car
6 loop 11 stacker car
Figure 3 — Exemplary layout of a cut-to-length line
Key
1 uncoiler 4 shear (covered by the scope) or
2 peeler press, laser (not covered by the scope)
3 straightener 5 conveyor belt
6 coil car
Figure 4 — Exemplary layout of a feeding line
---------------------- Page: 11 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

EN 614-1:2006+A1:2009, Safety of machinery - Ergonomic design principles - Part 1: Terminology and

general principles

EN 614-2, Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of

machinery and work tasks

EN 842, Safety of machinery - Visual danger signals - General requirements, design and testing

EN 894-1, Safety of machinery - Ergonomics requirements for the design of displays and control actuators -

Part 1: General principles for human interactions with displays and control actuators

EN 894-2, Safety of machinery - Ergonomics requirements for the design of displays and control actuators -

Part 2: Displays

EN 894-3, Safety of machinery - Ergonomics requirements for the design of displays and control actuators -

Part 3: Control actuators
EN 953,

EN 981, Safety of machinery - System of auditory and visual danger and information signals

EN 1299, Mechanical vibration and shock - Vibration isolation of machines - Information for the application

of source isolation

EN 12198-3, Safety of machinery - Assessment and reduction of risks arising from radiation emitted by

machinery - Part 3: Reduction of radiation by attenuation or screening
EN 12254, Screens for laser working places - Safety requirements and testing

EN 12464-1, Light and lighting - Lighting of work places - Part 1: Indoor work places

EN 13861, Safety of machinery - Guidance for the application of ergonomics standards in the design of

machinery

EN 14253, Mechanical vibration – Measurement and calculation of occupational exposure to whole-body

vibration with reference to health – Practical guidance

EN 60204-1:2006, Safety of machinery - Electrical equipment of machines - Part 1: General requirements

(IEC 60204-1)

EN 60447, Basic and safety principles for man-machine interface, marking and identification - Actuating

principles (IEC 60447)

EN 60825-1, Safety of laser products - Part 1: Equipment classification and requirements (IEC 60825- 1)

EN 60825-4, Safety of laser products - Part 4: Laser guards (IEC 60825-4)

EN 61310 (all parts), Safety of machinery - Indication, marking and actuation (IEC 61310)

---------------------- Page: 12 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)

EN 61496-1, Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements

and tests (IEC 61496-1)
EN ISO 361, Basic ionizing radiation symbol (ISO 361)

EN ISO 4413, Hydraulic fluid power - General rules and safety requirements for systems and their

components (ISO 4413)

EN ISO 4414, Pneumatic fluid power - General rules and safety requirements for systems and their

components (ISO 4414)

EN ISO 4871:2009, Acoustics - Declaration and verification of noise emission values of machinery and

equipment (ISO 4871:1996)

EN ISO 7010, Graphical symbols - Safety colours and safety signs - Registered safety signs (ISO 7010)

EN ISO 7731, Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731)

EN ISO 11064-1, Ergonomic design of control centres - Part 1: Principles for the design of control centres

(ISO 11064-1)

EN ISO 11064-2, Ergonomic design of control centres - Part 2: Principles for the arrangement of control

suites (ISO 11064-2)

EN ISO 11064-3, Ergonomic design of control centres - Part 3: Control room layout (ISO 11064-3)

EN ISO 11064-6, Ergonomic design of control centres - Part 6: Environmental requirements for control

centres (ISO 11064-6)

EN ISO 11202, Acoustics - Noise emitted by machinery and equipment - Determination of emission sound

pressure levels at a work station and at other specified positions applying approximate environmental

corrections (ISO 11202)
EN ISO 11553 (all parts), Safety of machinery - Laser processing machines

EN ISO 12100:2010, Safety of machinery - General principles for design - Risk assessment and risk reduction

(ISO 12100:2010)

EN ISO 13732-1, Ergonomics of the thermal environment - Methods for the assessment of human responses

to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1)

EN ISO 13850:2015, Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)

EN ISO 13854, Safety of machinery - Minimum gaps to avoid crushing of parts of the human body (ISO

13854)

EN ISO 13849-1:2015, Safety of machinery - Safety-related parts of control systems - Part 1: General

principles for design (ISO 13849-1:2015)

EN ISO 13855, Safety of machinery - Positioning of safeguards with respect to the approach speeds of parts

of the human body (ISO 13855)

EN ISO 13857, Safety of machinery - Safety distances to prevent hazard zones being reached by upper and

lower limbs (ISO 13857)
---------------------- Page: 13 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)

EN ISO 14118, Safety of machinery - Prevention of unexpected start-up (ISO 14118)

EN ISO 14119, Safety of machinery - Interlocking devices associated with guards - Principles for design and

selection (ISO 14119)

EN ISO 14120, Safety of machinery - Guards - General requirements for the design and construction of fixed

and movable guards (ISO 14120)

EN ISO 14122-1, Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed

means and general requirements of access (ISO 14122-1)

EN ISO 14122-2, Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms

and walkways (ISO 14122-2)

EN ISO 14122-3, Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders

and guard-rails (ISO 14122-3)

EN ISO 14122-4, Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO

14122-4)

EN ISO 14123-1, Safety of machinery - Reduction of risks to health resulting from hazardous substances

emitted by machinery - Part 1: Principles and specifications for machinery manufacturers (ISO 14123-1)

EN ISO 14123-2, Safety of machinery - Reduction of risks to health resulting from hazardous substances

emitted by machinery - Part 2: Methodology leading to verification procedures (ISO 14123-2)

ISO 3864-1, Graphical symbols - Safety colours and safety signs - Part 1: Design principles for safety signs

and safety markings

ISO 6183, Fire protection equipment - Carbon dioxide extinguishing systems for use on premises - Design

and installation
---------------------- Page: 14 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
3 Terms and definitions

For the purposes of this document, the terms and definitions given in EN ISO 12100:2010 and the

following apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

• ISO Online browsing platform: available at https://www.iso.org/obp
• IEC Electropedia: available at http://www.electropedia.org/
3.1
finishing line

machinery used for the customer-specific manufacture of metal strip or metal foil by one of the following

lines, their combination or, in addition, a combination with machinery which is not covered by this

standard (e.g. presses, milling machines, lasers):
3.1.1
slitting line

machinery to cut the strip into minimum two defined strip widths by longitudinal separation

3.1.2
cut-to-length line

machinery to cut the strip into defined strip lengths by cross-sectional separation

3.1.3
feeding line
machinery to prepare and/or feed the strip to subsequent processing
3.1.4
trimming line

machinery to cut the strip to a defined strip width and/or to increase strip edge quality by longitudinal

separation (e.g. side/edge trimming shear)
3.1.5
rounding machine
machinery for removing a burr
3.1.6
strip edge machining line

machinery for machining or shaping the strip edge, e.g. after trimming or rounding

3.1.7
inspection line

machinery for the visual, manual or automatic detection of the material condition (e. g surface, edge,

dimension, flatness, pores)
3.1.8
recoiling line

machinery for rewinding the strip (e.g. changing top to bottom side, spool changing)

3.1.9
separator line
machinery for separating layers of multi-layer strips, e.g. aluminium foil
---------------------- Page: 15 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
3.1.10
doubler line
machinery for producing multi-layer strips, e.g. aluminium foil
3.2
changing device
machinery for the operational change of rollers, shafts, reels and tools
3.3
material feeding

machinery via which the material is fed to a finishing line and which are linked to the control system of

the finishing line
EXAMPLE Coil car.
3.4
material removal

machinery via which the material is removed from a finishing line and which are linked to the control

system of the finishing line
3.5
safety layout

graphic overview of the finishing line with an arrangement of safety-related elements and areas

Note 1 to entry: 5.2.4 specifies the safety related elements to be shown on the safety layout.

3.6
trained person(nel)

skilled person with system knowledge, background knowledge, experience and/or ability to perform a

specific task and are aware of the hazards related to their duties
3.7
authorized person(nel)

trained person who is instructed by the user to perform a specific task on a specific equipment

Note 1 to entry: An unauthorized person does not have the required qualification and is not adequately equipped,

e.g. PPE.
3.8
maintenance

combination of service, inspection, reconditioning and functional test of the equipment

Note 1 to entry: The purpose is to preserve the working condition or returning to this condition so that the

finishing line is able to perform the required function (including safety requirements).

3.8.1
service
measure to maintain the nominal condition

Note 1 to entry: The nominal condition can be maintained in general without dismantling/disassembling major

parts of the equipment, e.g. cleaning, lubrication of the work equipment as well as addition or replacement of agents

or by replacing tools or operational changing parts.
---------------------- Page: 16 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
3.8.2
inspection
measure to observe and assess the current condition as well as fault finding

Note 1 to entry: Measures, e.g. measuring, testing, diagnostics including the determination of the causes of wear

or damage and the derivation of the necessary consequences for the continued use.

Note 2 to entry: 3.10.2 does not cover "material inspection", see 3.17.
3.8.3
reconditioning

foreseeable measure (s) to return to the nominal condition and requiring dismantling/disassembling

Note 1 to entry: Foreseeable Measure, e.g. replacement of worn parts, damaged parts, or parts having expired the

foreseen lifetime. These parts should meet manufacturers' specification.
3.8.4
functional test
checking the functionality of the exchanged or repaired parts

Note 1 to entry: It is maybe required to carry out adjustment work, e.g. test runs, verifying safety functions.

3.9
repair
not foreseeable measure(s) to return to the nominal condition

Note 1 to entry: Measure to replace damaged parts, requires in general dismantling/disassembling. These parts

should meet manufacturers' specification
3.10
material
metal strip/foil or coils used in the finishing process
3.11
material inspection
observe and assess the current condition of the material
3.12
cobbling
material leaving its intended path
3.13
sleeve (spool)
cylindrical hollow body for winding the material
3.14
coil
winded material
3.15
plate (sheet)
cut material
---------------------- Page: 17 ----------------------
oSIST prEN 17449:2020
prEN 17449:2019 (E)
3.16
stack
stacked cut-to-size material
3.17
pulpit

enclosed room in which the control desk and monitoring facilities for a machine or equipment are located,

used as a permanent work station.
3.18
control stand
free standing control desk (usually situated adjacent to the machine or equip
...