prEN ISO 20500-7

Mobile road construction machinery - Safety - Part 7: Specific requirements for slipform paver and texture curing machines (ISO/DIS 20500-7:2020)

This part of ISO 20500, together with part 1, deals with all significant hazards for slipform paver and texture curing machines when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer associated with the whole life time of the machine (see Clause 4).
The requirements of this part are complementary to the common requirements formulated in ISO 20500-1.
This document does not repeat the requirements from ISO 20500-1, but adds or replaces the requirements for application for slipform paver and texture curing machines.

Bewegliche Straßenbaumaschinen - Sicherheit - Teil 7: Besondere Anforderungen an Gleitschalungsfertiger und Nachbehandlungsgeräte (ISO/DIS 20500-7:2020)

Dieser Teil von ISO 20500 behandelt, zusammen mit Teil 1, alle signifikanten Gefährdungen für Gleitschalungsfertiger und Nachbehandlungsgeräte, wenn diese bestimmungsgemäß und unter den vernünftigerweise vom Hersteller vorhersehbaren Fehlbedienungsbedingungen während der gesamten Lebensdauer der Maschine verwendet werden (siehe Anhang D).
Die Anforderungen dieses Teils ergänzen die gemeinsamen Anforderungen, die in ISO 20500 1 formuliert sind.
Dieses Dokument wiederholt nicht die Anforderungen aus ISO 20500 1, sondern ergänzt oder ersetzt die Anforderungen zur Anwendung für Straßenfertiger.
Die folgenden signifikanten und relevanten Gefährdungen werden in diesem Dokument nicht behandelt:
- Blitzeinschlag.

Machines mobiles pour la construction de routes - Sécurité - Partie 7: Prescriptions spécifiques pour machines à coffrage glissant et de traitement de surface (ISO/DIS 20500-7:2020)

Premični stroji za gradnjo cest - Varnost - 7. del: Posebne zahteve za finišer z drsnim opažem in stroje za strjevanje teksture (ISO/DIS 20500-7:2020)

General Information

• Status: Not Published
• Publication Date: 21-Aug-2023
• ICS: 93.080.10 - Road construction
• Technical Committee: CEN/TC 151 - Construction equipment and building material machines - Safety
• Drafting Committee: CEN/TC 151/WG 5 - Road construction machines - Safety
• Current Stage: 4599 - Dispatch of FV draft to CMC - Finalization for Vote
• Start Date: 19-Dec-2022
• Completion Date: 19-Dec-2022
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: oSIST prEN ISO 20500-7:2020 - Mobile road construction machinery - Safety - Part 7: Specific requirements for slipform paver and texture curing machines (ISO/DIS 20500-7:2020)

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2020
Premični stroji za gradnjo cest - Varnost - 7. del: Posebne zahteve za finišer z
drsnim opažem in stroje za strjevanje teksture (ISO/DIS 20500-7:2020)
Mobile road construction machinery - Safety - Part 7: Specific requirements for slipform
paver and texture curing machines (ISO/DIS 20500-7:2020)
Bewegliche Straßenbaumaschinen - Sicherheit - Teil 7: Besondere Anforderungen an
Gleitschalungsfertiger und Nachbehandlungsgeräte (ISO/DIS 20500-7:2020)
Machines mobiles pour la construction de routes - Sécurité - Partie 7: Prescriptions
spécifiques pour machines à coffrage glissant et de traitement de surface (ISO/DIS
20500-7:2020)
Ta slovenski standard je istoveten z: prEN ISO 20500-7
ICS:
93.080.10 Gradnja cest Road construction
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 20500-7
ISO/TC 195 Secretariat: SAC
Voting begins on: Voting terminates on:
2020-07-10 2020-10-02
Mobile road construction machinery — Safety —
Part 7:
Specific requirements for slipform paver and texture
curing machines
Machines mobiles pour la construction de routes — Sécurité —
Partie 7: Prescriptions spécifiques pour finisseurs
ICS: 93.080.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 20500-7:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020

ISO/DIS 20500-7:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO/DIS 20500-7:2020(E)
Contents Page
Foreword . v
Introduction . vii
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Safety requirements and/or protective/risk reduction measures .3
4.1 General .3
4.2 Visibility .3
4.2.1 Visibility performance criteria .3
4.2.2 Visibility performance criteria for the front boundary FB .4
4.3 Operation and handling .4
4.4 Operator's station .5
4.5 Access systems to operator's station and to maintenance points.5
4.6 Protection .5
4.7 Signal devices and warning signs.5
4.8 Electro-magnetic compatibility (EMC) .5
4.9 Noise and vibration .6
4.10 Conveyors .6
5 Verification of the safety requirements and/or protective/risk reduction measures .6
6 Information for use .7
6.1 Instruction handbook .7
Annex A (normative) Noise test code for slipform pavers .8
A.1 Scope .8
A.2 Determination of A-weighted sound power level .8
A.2.1 General .8
A.2.2 Measurement surface .8
A.2.3 Size of the measurement surface .8
A.2.4 Microphone positions on the hemispherical measurement surface .9
A.2.5 Positioning of the machine .9
A.2.6 Repetition of the test . 10
A.3 Determination of A-weighted emission sound pressure level at the operator's
position . 10
A.3.1 General . 10
A.3.2 Enclosed operator's positions . 10
A.3.3 Quantities to be determined . 10
A.3.4 Repetition of the test . 10
A.3.5 Microphone position(s) . 10
A.4 Operation conditions . 10
A.4.1 Fan speed . 10
A.4.2 Operating conditions for working units . 11
A.5 Uncertainty . 11
A.6 Information to be recorded . 12
A.7 Information to be reported . 12
iii
ISO/DIS 20500-7:2020(E)
A.8 Declaration and verification of noise emission values . 13
Annex B (informative) Examples of slipform pavers . 14
Annex C (informative) Examples of texture curing machines . 16
Annex D (informative) List of significant hazards . 17
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 22

iv
ISO/DIS 20500-7:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document ISO 20500-7 was prepared by Technical Committee ISO/TC 195, Building construction
machinery and equipment.
ISO 20500 consists of the following parts, under the general title Mobile road construction machinery —
Safety:
— Part 1: Common requirements
— Part 2: Specific requirements for road-milling machines
— Part 3: Specific requirements for soil-stabilising machines and recycling machines
— Part 4 Specific requirements for compaction machines
— Part 5: Specific requirements for paver-finishers
— Part 6: Specific requirements for mobile feeders
— Part 7: Specific requirements for slipform paver and texture curing machines
A list of all parts in the ISO 20500 series can be found on the ISO website.
v
ISO/DIS 20500-7:2020(E)
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
vi
ISO/DIS 20500-7:2020(E)
Introduction
This International Standard is a type C standard as stated in ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered
are indicated in the scope of this International Standard.
When provisions of this type C standard are different from those which are stated in type A or B
standards, the provisions of this type C standard take precedence over the provisions of the other
standards for machines that have been designed and built according to the provisions of this type C
standard.
vii
DRAFT INTERNATIONAL STANDARD ISO/DIS 20500-7:2020(E)
Mobile road construction machinery — Safety —
Part 7:
Specific requirements for slipform paver and
...