EN ISO 15013:2022

Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2022)

This document specifies the requirements and test methods for solid flat extruded sheets of polypropylene homopolymers (PP‑H) and polypropylene copolymers (PP‑B and PP‑R) without fillers or reinforcing materials. This document applies to PP sheet in rolled form. It applies only to thicknesses of 0,5 mm to 40 mm.

Kunststoffe - Extrudierte Tafeln aus Polypropylen (PP) - Anforderungen und Prüfverfahren (ISO 15013:2022)

Dieses Dokument legt die Anforderungen und Prüfverfahren für massive, ebene, extrudierte Tafeln aus Polypropylen-Homopolymerisaten (PP H) und Polypropylen-Copolymerisaten (PP B und PP R) ohne Füll- oder Verstärkungsstoffe fest. Dieses Dokument gilt für gerollte PP-Tafeln. Es ist nur anzuwenden für Tafeldicken von 0,5 mm bis 40 mm.

Plastiques - Plaques extrudées en polypropylène (PP) - Exigences et méthodes d'essai (ISO 15013:2022)

Le présent document spécifie les exigences et les méthodes d’essai relatives aux plaques compactes et planes, extrudées en polypropylène homopolymère (PP-H) et polypropylène copolymère (PP-B et PP-R) sans adjonction de charges ni de renforts. Le présent document s’applique aux plaques en PP enroulées en rouleaux. Elle s’applique uniquement aux plaques d’épaisseur comprise entre 0,5 mm et 40 mm.

Polimerni materiali - Ekstrudirane plošče iz polipropilena (PP) - Zahteve in preskusne metode (ISO 15013:2022)

Ta dokument določa zahteve in preskusne metode za masivne ravne ekstrudirane plošče iz polipropilen homopolimerov (PP H) oziroma polipropilen kopolimerov (PP B in PP R) brez polnil ali materialov za ojačanje. Ta dokument se uporablja za valjane plošče iz polipropilena. Uporablja se le za debeline od 0,5 mm do 40 mm.

General Information

• Status: Published
• Publication Date: 08-Mar-2022
• Withdrawal Date: 29-Sep-2022
• ICS: 83.140.10 - Films and sheets
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 09-Mar-2022
• Completion Date: 09-Mar-2022
• Ref Project: SIST EN ISO 15013:2022 - Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2022)

Relations

• Replaces: EN ISO 15013:2007 - Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2007)
• Effective Date: 16-Mar-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2022
Nadomešča:
SIST EN ISO 15013:2008
Polimerni materiali - Ekstrudirane plošče iz polipropilena (PP) - Zahteve in
preskusne metode (ISO 15013:2022)
Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO
15013:2022)
Kunststoffe - Extrudierte Tafeln aus Polypropylen (PP) - Anforderungen und Prüfung
(ISO 15013:2022)
Plastiques - Plaques extrudées en polypropylène (PP) - Exigences et méthodes d'essai
(ISO 15013:2022)
Ta slovenski standard je istoveten z: EN ISO 15013:2022
ICS:
83.140.10 Filmi in folije Films and sheets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 15013
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 15013:2007
English Version
Plastics - Extruded sheets of polypropylene (PP) -
Requirements and test methods (ISO 15013:2022)
Plastiques - Plaques extrudées en polypropylène (PP) - Kunststoffe - Extrudierte Tafeln aus Polypropylen (PP)
Exigences et méthodes d'essai (ISO 15013:2022) - Anforderungen und Prüfung (ISO 15013:2022)
This European Standard was approved by CEN on 24 January 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15013:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 15013:2022) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards
shall be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15013:2007.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15013:2022 has been approved by CEN as EN ISO 15013:2022 without any modification.

INTERNATIONAL ISO
STANDARD 15013
Third edition
2022-02
Plastics — Extruded sheets of
polypropylene (PP) — Requirements
and test methods
Plastiques — Plaques extrudées en polypropylène (PP) — Exigences
et méthodes d'essai
Reference number
ISO 15013:2022(E)
ISO 15013:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ISO 15013:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material. 1
5 Requirements . 2
5.1 Appearance . 2
5.2 Dimensional tolerances . 2
5.2.1 Thickness . 2
5.2.2 Length and width . . 2
5.2.3 Rectangularity . 3
5.2.4 Bow of sheets in rolled form . 3
5.3 Properties . 3
5.3.1 Mechanical and thermal properties . 3
5.3.2 Behaviour on heating . 4
5.3.3 Physiological behaviour . 4
6 Test methods . 4
6.1 Test specimens. 4
6.1.1 Preparation of test specimens . 4
6.1.2 Conditioning . 4
6.1.3 Testing . 4
6.2 Delivery condition . 4
6.3 Appearance . 5
6.4 Dimensions . 5
6.4.1 Thickness, h . 5
6.4.2 Length, l, and width, b . . . 5
6.4.3 Rectangularity . 5
6.4.4 Bow of sheets in rolled form . 5
6.5 Tensile stress at yield, σ , and tensile strain at yield, ε . 5
y y
6.6 Modulus of elasticity in tension, E . 5
t
6.7 Charpy impact strength of notched specimens, a . 5
cn
6.8 Melt mass-flow rate (MFR) . 6
6.9 Heat resistance . 6
6.10 Determination of shrinkage on heating . 6
7 Designation and order specification . 7
7.1 Example for sheets . 7
7.2 Example for sheets in rolled form . 8
8 Marking . . 8
Annex A (normative) Requirements for rectangularity . 9
iii
ISO 15013:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent r
...