CEN/TS 1453-2:2017

Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity

This Technical Specification gives guidance for the assessment of conformity of formulations, products and assemblies in accordance with EN 1453 1 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
If certification is involved, it is recommended that the certification body is preferably compliant with EN ISO/IEC 17065 [5] or EN ISO/IEC 17021 [3], as applicable.
In order to help the reader, a basic test matrix is given in Annex A, Table A.1.
In conjunction with EN 1453 1, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC-U) intended to be used for the following purposes:
-   for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B");
This is reflected in the marking of products by "B".

Kunststoff-Rohrleitungssysteme mit Rohren mit profilierter Wandung zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebäuden - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für die Beurteilung der Konformität

Diese Technische Spezifikation gibt Empfehlungen für die Beurteilung der Konformität von Formmassen, Erzeugnissen und Bauteilkombinationen, die, in Übereinstimmung mit FprEN 1453-1:2016, für eine Einbeziehung in den Qualitätssicherungsplan des Herstellers als Teil des Qualitätsmanagementsystems und für die Erstellung von Zertifizierungsverfahren vorgesehen sind.
Es wird empfohlen, dass das Qualitätsmanagementsystem den zutreffenden Anforderungen nach EN ISO 9001 [1] oder mindestens ebenso strengen Anforderungen entspricht.
Falls Zertifizierung einbezogen ist, wird empfohlen, dass die Zertifizierungsstelle vorzugsweise EN ISO/IEC 17065 [5] oder EN ISO/IEC 17021 [3], wie zutreffend, entspricht.
Zur Unterstützung des Lesers enthält Anhang A, Tabelle A.1, einen Überblick über das Prüfsystem.
Dieses Dokument gilt in Verbindung mit FprEN 1453-1:2016 für Rohrleitungssysteme aus weichmacherfreiem Polyvinylchlorid (PVC-U), die für folgende Verwendungszwecke vorgesehen sind:
-   für Systeme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebäuden (Anwendungskennzeichen "B")
Dies wird durch die Kennzeichnung auf dem Erzeugnis durch "B" angezeigt.

Systèmes de canalisations en plastique avec des tubes à paroi structurée pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur des bâtiments - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2: Guide pour l'évaluation de la conformité

Cevni sistemi iz polimernih materialov s strukturirano steno cevi za nizko- in visokotemperaturne odvodne sisteme v stavbah - Nemehčan polivinilklorid (PVC-U) - 2. del: Navodilo za ugotavljanje skladnosti

Ta tehnična specifikacija podaja navodila za ugotavljanje skladnosti formulacij, izdelkov in sestavov v skladu s standardom FprEN 1453 1:2016, pri čemer naj bi se te informacije vključile v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti in za vzpostavitev postopka certificiranja.
Priporoča se, da je sistem vodenja kakovosti skladen s standardom EN ISO 9001 [1] oziroma da ni manj strog od ustreznih zahtev iz tega standarda.
Pri certificiranju se priporoča, da je certifikacijski organ akreditiran v skladu s standardom EN ISO/IEC 17065 [5] ali EN ISO/IEC 17021 [3].
V pomoč bralcem preglednica A.1 dodatka A vsebuje osnovno preskusno matriko.
Ta dokument se v povezavi s standardom FprEN 1453 1:2016 uporablja za cevne sisteme iz nemehčanega polivinilklorida (PVC-U), ki naj bi se uporabljali za:
– (nizko- in visokotemperaturne) odvodne sisteme v stavbah (koda območja uporabe »B«).
To je razvidno iz oznake »B« na izdelkih.

General Information

• Status: Published
• Publication Date: 21-Mar-2017
• ICS: 23.040.01 - Pipeline components and pipelines in general
• ICS: 91.140.80 - Drainage systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 33 - Thermoplastics piping systems for soil & waste discharge and non-pressure drainage and sewerage
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 04-Oct-2024
• Ref Project: SIST-TS CEN/TS 1453-2:2017 - Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity

Relations

• Replaces: ENV 1453-2:2000 - Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
• Effective Date: 29-Mar-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2017
1DGRPHãþD
SIST ENV 1453-2:2001
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORYVVWUXNWXULUDQRVWHQRFHYL]DQL]NRLQ
YLVRNRWHPSHUDWXUQHRGYRGQHVLVWHPHYVWDYEDK1HPHKþDQSROLYLQLONORULG39&
8GHO1DYRGLOR]DXJRWDYOMDQMHVNODGQRVWL
Plastics piping systems with structured wall pipes for soil and waste discharge (low and
high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2:
Guidance for the assessment of conformity
Kunststoff-Rohrleitungssysteme mit Rohren mit profilierter Wandung zum Ableiten von
Abwasser (niedriger und hoher Temperatur) innerhalb von Gebäuden -
Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für die Beurteilung
der Konformität
Systèmes de canalisations en plastique avec des tubes à paroi structurée pour
l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à
l'intérieur des bâtiments - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2 : Guide
pour l'évaluation de la conformité
Ta slovenski standard je istoveten z: CEN/TS 1453-2:2017
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
91.140.80 Drenažni sistemi Drainage systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

CEN/TS 1453-2
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
March 2017
TECHNISCHE SPEZIFIKATION
ICS 23.040.01; 91.140.80 Supersedes ENV 1453-2:2000
English Version
Plastics piping systems with structured wall pipes for soil
and waste discharge (low and high temperature) inside
buildings - Unplasticized poly(vinyl chloride) (PVC-U) -
Part 2: Guidance for the assessment of conformity
Systèmes de canalisations en plastique avec des tubes à Kunststoff-Rohrleitungssysteme mit Rohren mit
paroi structurée pour l'évacuation des eaux-vannes et profilierter Wandung zum Ableiten von Abwasser
des eaux usées (à basse et à haute température) à (niedriger und hoher Temperatur) innerhalb von
l'intérieur des bâtiments - Poly(chlorure de vinyle) non Gebäuden - Weichmacherfreies Polyvinylchlorid (PVC-
plastifié (PVC-U) - Partie 2: Guide pour l'évaluation de U) - Teil 2: Empfehlungen für die Beurteilung der
la conformité Konformität
This Technical Specification (CEN/TS) was approved by CEN on 30 November 2016 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 1453-2:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Abbreviated terms . 9
5 General . 10
6 Testing and inspection . 10
6.1 Material specification . 10
6.2 Grouping . 11
6.2.1 General . 11
6.2.2 Size groups . 11
6.3 Type testing . 11
6.4 Batch release tests . 13
6.5 Process verification tests . 14
6.6 Audit tests . 15
6.7 Indirect tests . 16
6.8 Test records . 17
Annex A (informative) Basic test matrix . 18
Bibliography . 19

European foreword
This document (CEN/TS 1453-2:2017) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes ENV 1453-2:2000.
Compared with ENV 1453-2:2000, the following changes have been made:
a) use of the template drafted by CEN/TC 155/WG 21 for assessment of conformity documents
(change of “Terms and definitions” and addition of 1 column “Sampling procedures” in Tables);
b) introduction of “Limits of addition of PVC reprocessed and recycled material” in a separate table
(Table 2);
c) deletion of all requirements for TPE seals as they are no longer required;
d) addition of an informative Annex A: Basic test matrix.
EN 1453, Plastics piping systems with structured wall pipes for soil and waste discharge (low and high
temperature) inside buildings — Unplasticized poly(vinyl chloride) (PVC-U), consists of the following
Parts:
— Part 1: Specifications for pipes and the system
— Part 2: Guidance for the assessment of conformity (the present Technical Specification)
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Introduction
Figures 1 and 2 are intended to provide general information on the concept of testing and organization
of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type test
(TT), batch release test (BRT), process verification test (PVT) and audit test (AT), this part of EN 1453
details the applicable characteristics to be assessed and the frequency and sampling of testing.
A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings, valves or
assemblies by manufacturers is given in Figure 1.

Figure 1 — Typical scheme for the assessment of conformity by a manufacturer
A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings, valves or
assemblies by manufacturers, including certification, is given in Figure 2.
Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including
certification
1 Scope
This Technical Specification gives guidance for the assessment of conformity of formulations, products
and assemblies in accordance with EN 1453-1 intended to be included in the manufacturer’s quality
plan as part of the quality management system and for the establishment of certification procedures.
It is recommended that the quality management system conforms to or is no less stringent than the
relevant requirements to EN ISO 9001 [1].
If certification is involved, it is recommended that the certification body is preferably compliant with
EN ISO/IEC 17065 [5] or EN ISO/IEC 17021 [3], as applicable.
In order to help the reader, a basic test matrix is given in Annex A, Table A.1.
In conjunction with EN 1453-1, this document is applicable to piping systems made of unplasticized
poly(vinyl chloride) (PVC-U) intended to be used for the following purposes:
— for soil and waste discharge systems (low and high temperature) inside buildings (application area
code “B”);
This is reflected in the marking of products by “B”.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 1453-1:2017, Plastics piping systems with structured-wall pipes for soil and waste discharge (low and
high temperature) inside buildings — Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications
for pipes and the system
3 Terms and definitions
For the purposes of this Technical Specification, the terms and definitions given in EN 1453-1 and the
following apply.
3.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
Note 1 to entry: A certification body is preferably compliant with EN ISO/IEC 17065 [5].
3.2
inspection body
body, that performs inspection
Note 1 to entry: A body can be an organization, or part of an organization.
Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 [2].
3.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
Note 1 to entry: In the context of this part of EN 1453, the materials and products can be subjected to type
testing, batch release testing, process verification testing, audit testing and witness testing, as applicable.
Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 [5].
3.4
quality management system
management system to direct and control an organization with regard to quality
Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [1].
3.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.6
type testing
TT
testing performed to prove that the formulation, product, joint or assembly is capable of conforming to
the requirements given in the relevant standard
Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly
provided that the process verification tests are done regularly.
3.7
batch release test
BRT
test performed by or on behalf of the manufacturer on a batch of formulations or products, which needs
to be satisfactorily completed before the batch can be released
3.8
process verification test
PVT
test performed by, or on behalf of the manufacturer on formulation, products or joints or assemblies at
specific intervals to confirm that the process continues to be capable of producing products which
conform to the requirements given in the relevant standard
Note 1 to entry: Such tests are not required to release batches of formulations or products; rather they are
carried out
...