iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13523-18:2002

(Main)

Coil coated metals - Test methods - Part 18: Resistance to staining

Coil coated metals - Test methods - Part 18: Resistance to staining

This Part of EN 13523 specifies test procedures for assessing the effect of chemicals on the characteristics of an organic coating on a metallic substrate. It covers testing by using defined substances and to assess the change in characteristics such as discoloration, change in gloss, blistering, softening, swelling and loss of adhesion. Assessment of other phenomena may be agreed between the interested parties.

Bandbeschichtete Metalle - Prüfverfahren - Teil 18: Beständigkeit gegen Fleckenbildung

Dieser Teil von EN 13523 beschreibt Verfahren, mit denen der Einfluss von Chemikalien auf die Eigenschaften einer organischen Beschichtung auf einem metallischen Substrat abgeschätzt werden kann. Er schließt die Prüfung mit definierten Substanzen und die Bewertung von Eigenschaftsänderungen wie Verfärbung, Glanzänderung, Blasenbildung, Erweichen, Quellen und Haftfestigkeitsverlust ein. Andere Phänomene dürfen nach Vereinbarung zwischen den Vertragspartnern bewertet werden.

Tôles prélaquées - Méthodes d'essai - Partie 18 : Résistance aux taches

La présente partie de l'EN 13523 spécifie des méthodes d'évaluation de l'incidence des produits chimiques sur les caractéristiques d'un revêtement organique appliqué sur un support métallique. Elle couvre les essais effectués avec des substances définies afin d'évaluer les changements de caractéristiques (décoloration, changement de brillant, cloquage, ramollissement, gonflement et perte d'adhérence). L'évaluation d'autres phénomènes peut faire l'objet d'un accord entre les parties.

Kovine, zaščitene po postopku coil-coating - Metode preskušanja - 18. del: Odpornost proti nastanku madežev

General Information

Status
Withdrawn
Publication Date
16-Jul-2002
Withdrawal Date
02-Jun-2020
ICS
17.040.20 - Properties of surfaces
25.220.60 - Organic coatings
Technical Committee
CEN/TC 139 - Paints and varnishes
Drafting Committee
CEN/TC 139/WG 9 - Testing of coil coated metals
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
03-Jun-2020
Ref Project
SIST EN 13523-18:2003 - Coil coated metals - Test methods - Part 18: Resistance to staining

Relations

Replaced By
EN 13523-18:2020 - Coil coated metals - Test methods - Part 18: Resistance to staining
Effective Date
10-Jun-2020

Buy Standard

EN 13523-18:2003EN 13523-18:2003
PreviousNext
Standard
EN 13523-18:2003
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 18: Beständigkeit gegen FleckenbildungTôles prélaquées - Méthodes d'essai - Partie 18 : Résistance aux tachesCoil coated metals - Test methods - Part 18: Resistance to staining25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:EN 13523-18:2002SIST EN 13523-18:2003en01-januar-2003SIST EN 13523-18:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13523-18July 2002ICS 17.040.20; 25.220.60English versionCoil coated metals - Test methods - Part 18: Resistance tostainingTôles prélaquées - Méthodes d'essai - Partie 18:Résistance aux tâchesBandbeschichtete Metalle - Prüfverfahren - Teil 18:Beständigkeit gegen FleckenbildungThis European Standard was approved by CEN on 11 April 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13523-18:2002 ESIST EN 13523-18:2003
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13523-1:2024(Main)
Coil coated metals - Test methods - Part 1: Film thickness
SIST EN 13523-1:2024

This document specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Five appropriate methods are given in this document:
a)   magnetic induction;
b)   eddy current;
c)   micrometer;
d)   optical;
e)   ruggedized optical interference.
The methods are applicable only to products with smooth and flat substrates, but the coating itself can be textured. In that case, for methods a) and b), the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness, method d) can provide the minimum, maximum and average thickness, and e) will give the total thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness are only applicable on method a).

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-4:2014(Main)
Coil coated metals - Test methods - Part 4: Pencil hardness
SIST EN 13523-4:2014

This part of EN 13523 describes the procedure to assess the relative hardness of an organic coating on a metallic substrate, by means of pencils of known hardness.
Smooth surfaces will give more accurate results but the method is also applicable for textured surfaces. The more pronounced the texture, the greater the unreliability of results.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-5:2014(Main)
Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
SIST EN 13523-5:2014

This part of EN 13523 specifies the procedure for determining the resistance to cracking and/or pick-off on rapid deformation of an organic coating on a metallic substrate in terms of energy which the specimen will withstand.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-13:2014(Main)
Coil coated metals - Test methods - Part 13: Resistance to accelerated ageing by the use of heat
SIST EN 13523-13:2014

This Part of EN 13523 describes the procedure for determining the behaviour of an organic coating on a metallic substrate (flat or bent specimens) when submitted to accelerated ageing by heating at a defined temperature for a defined period of time. It is not possible to test heat resistance in such way as to control all possible conditions of use. The aim of this test is therefore to furnish the basic test methods for the effect of heat. NOTE: Special applications may require that properties other than those mentioned in this part of EN 13523 be checked.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-1:2024(Main)
Coil coated metals - Test methods - Part 1: Film thickness
SIST EN 13523-1:2024

This document specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Five appropriate methods are given in this document:
a)   magnetic induction;
b)   eddy current;
c)   micrometer;
d)   optical;
e)   ruggedized optical interference.
The methods are applicable only to products with smooth and flat substrates, but the coating itself can be textured. In that case, for methods a) and b), the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness, method d) can provide the minimum, maximum and average thickness, and e) will give the total thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness are only applicable on method a).

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-4:2014(Main)
Coil coated metals - Test methods - Part 4: Pencil hardness
SIST EN 13523-4:2014

This part of EN 13523 describes the procedure to assess the relative hardness of an organic coating on a metallic substrate, by means of pencils of known hardness.
Smooth surfaces will give more accurate results but the method is also applicable for textured surfaces. The more pronounced the texture, the greater the unreliability of results.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-5:2014(Main)
Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
SIST EN 13523-5:2014

This part of EN 13523 specifies the procedure for determining the resistance to cracking and/or pick-off on rapid deformation of an organic coating on a metallic substrate in terms of energy which the specimen will withstand.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13523-13:2014(Main)
Coil coated metals - Test methods - Part 13: Resistance to accelerated ageing by the use of heat
SIST EN 13523-13:2014

This Part of EN 13523 describes the procedure for determining the behaviour of an organic coating on a metallic substrate (flat or bent specimens) when submitted to accelerated ageing by heating at a defined temperature for a defined period of time. It is not possible to test heat resistance in such way as to control all possible conditions of use. The aim of this test is therefore to furnish the basic test methods for the effect of heat. NOTE: Special applications may require that properties other than those mentioned in this part of EN 13523 be checked.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12299:2024(Main)
Railway applications - Ride comfort for passengers - Measurement and evaluation
SIST EN 12299:2024

The purpose of this document is to provide methods for quantifying the ride comfort of a passenger in a rail vehicle in response to the track sections it is operated over.
The methods aim to quantify the effects of vehicle body motions on ride comfort and to make the assessment of passenger comfort predictable, repeatable, objective and meaningful.
The methods and comfort scales are validated for people of good health.
This document applies to passengers in rail vehicles operating on heavy rail networks.
This document applies to measurements of motions. It also applies to simulated motions. Guidance is provided on:
-   which method described within the document should be used for different scenarios;
-   typical values for different comfort levels;
-   the application of simulation.
This document excludes health and safety issues, non-passenger carrying vehicles, vehicle homologation and safety, limit values, motion sickness, discomfort caused by accelerating and braking, design guidelines and measurement technology.

  • Draft
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19403-4:2024(Main)
Paints and varnishes - Wettability - Part 4: Determination of the polar and dispersive fractions of the surface tension of liquids from an interfacial tension (ISO 19403-4:2024)
kSIST FprEN ISO 19403-4:2024

This document specifies a test method to determine the polar and dispersive fractions of the surface tension of liquids from an interfacial tension with optical methods. The method can be applied for the characterization of liquid coating materials, especially if drying effects occur during alternative measurement. If applied to liquids with non-Newtonian flow behaviour (see ISO 3219-1:2021, 3.22), restrictions can apply.

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day