prEN 1083-2
(Main)Power-driven brushes - Part 2: Safety requirements
Power-driven brushes - Part 2: Safety requirements
This document specifies requirements and measures for removal or reduction of hazards resulting from the design and application of power-driven brushes.
NOTE Power-driven brushing tools are e.g. cup brushes, wheel brushes, end brushes, disc brushes, tube brushes and head brushes.
This document also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer.
This document does not apply to cylinder brushes and strip brushes, brushes for car washing, vacuum cleaners, floor cleaning, drain and street cleaning machines and dental brushes.
Kraftbetriebene Bürstwerkzeuge - Teil 2: Sicherheitstechnische Anforderungen
Dieses Dokument legt sicherheitstechnische Anforderungen für kraftbetriebene Bürstwerkzeuge sowie Maßnahmen zur Beseitigung oder Verringerung von Gefährdungen fest, die sich aus der Konstruktion und Anwendung von kraftbetriebenen Bürstwerkzeugen ergeben.
ANMERKUNG Kraftbetriebene Bürstwerkzeuge sind z. B. Topfbürsten, Rundbürsten, Pinselbürsten, Tellerbürsten, Rohrbürsten und Kopfbürsten.
Dieses Dokument umfasst auch Verfahren und Prüfungen zur Feststellung der Übereinstimmung mit den Anforderungen sowie sicherheitsbezogene Benutzerinformationen, die der Hersteller dem Anwender zur Verfügung zu stellen hat.
Dieses Dokument gilt nicht für Walzenbürsten und Streifenbürsten, Bürsten für Fahrzeugwaschanlagen, Staubsauger, Bodenreinigungsmaschinen, Kanal- und Straßenreinigungsmaschinen und Dentalbürsten.
Brosses entraînées par un moteur - Partie 2: Exigences de sécurité
Le présent document spécifie les exigences et les mesures pour l'élimination ou la réduction des phénomènes dangereux résultant de la conception et de l'application des brosses motorisées.
NOTE Les outils de brossage motorisés sont par exemple les brosses coupe, les brosses circulaires, les brosses en bout, les brosses disque, les brosses rouleau et les brosses en tête.
Le présent document contient également des procédures et des essais pour la vérification de la conformité aux exigences ainsi que des informations sur la sécurité d'utilisation, qui doivent être mises à la disposition de l'utilisateur par le fabricant.
Le présent document ne s'applique pas aux brosses cylindriques et aux brosses en bande, aux brosses pour le lavage des voitures, les aspirateurs, les machines de nettoyage des sols, des égouts et des rues, ainsi qu'aux brosses à dents.
Krtače na električni pogon - 2. del: Varnostne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 1083-2:2024
01-januar-2024
Krtače na električni pogon - 2. del: Varnostne zahteve
Power-driven brushes - Part 2: Safety requirements
Kraftbetriebene Bürstwerkzeuge - Teil 2: Sicherheitstechnische Anforderungen
Brosses entraînées par un moteur - Partie 2: Exigences de sécurité
Ta slovenski standard je istoveten z: prEN 1083-2
ICS:
25.100.70 Brusiva Abrasives
oSIST prEN 1083-2:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 1083-2:2024
---------------------- Page: 2 ----------------------
oSIST prEN 1083-2:2024
DRAFT
EUROPEAN STANDARD
prEN 1083-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2023
ICS 25.100.70 Will supersede EN 1083-2:1997
English Version
Power-driven brushes - Part 2: Safety requirements
Brosses entraînées par un moteur - Partie 2: Exigences Kraftbetriebene Bürstwerkzeuge - Teil 2:
de sécurité Sicherheitstechnische Anforderungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 143.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1083-2:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 1083-2:2024
prEN 1083-2:2023 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and symbols . 5
3.1 Brushing machines . 5
3.2 Type of application . 6
3.3 Symbols . 7
4 List of significant hazards . 8
5 Safety requirements . 8
5.1 General requirements . 8
5.2 Safety factors . 8
5.3 Requirements for brushing too
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.