EN ISO 12215-3:2018
(Main)Small craft - Hull construction and scantlings - Part 3: Materials: Steel, aluminium alloys, wood, other materials (ISO 12215-3:2002)
Small craft - Hull construction and scantlings - Part 3: Materials: Steel, aluminium alloys, wood, other materials (ISO 12215-3:2002)
This part of ISO 12215 specifies requirements for materials intended for use in the construction of the hull, superstructure and appendages, in particular:
weldable normal and higher strength hot-rolled steel plates, wide flats, sections and bars; austenitic stainless steels, fabricated in the form of plates or profiles; wrought aluminium alloys fabricated as plates, sections and extruded profiles; wood in the form of solid timber, plywood or veneer; other suitable materials.
This part of ISO 12215 applies to small craft with a hull length (LH) according to ISO 8666 of up to 24 m.
Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 3: Werkstoffe: Stahl, Aluminiumlegierungen, Holz, andere Werkstoffe (ISO 12215-3:2002)
Petits navires - Construction de coques et échantillons - Partie 3: Matériaux: Acier, alliages d'aluminium, bois, autres matériaux (ISO 12215-3:2002)
La présente partie de l'ISO 12215 spécifie les exigences relatives aux matériaux destinés à être utilisés pour la construction de la coque, de la superstructure et des appendices, en particulier
les tôles d'acier soudables à résistance normale et élevée laminées à chaud, les aciers universels, les sections et les barres ;les aciers inoxydables austénitiques, fabriqués sous forme de tôles ou de profilés ;les alliages d'aluminium corroyés sous forme de tôles, de sections et de profilés extrudés ;le bois sous forme de bois massif, de contreplaqué ou de feuille de plaquage ;d'autres matériaux appropriés.
La présente partie de l'ISO 12215 est applicable aux petits navires de longueur de coque ( LH ) inférieure ou égale à 24 m, conformément à l'ISO 8666.
Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 3. del: Materiali: jeklo, aluminijeve zlitine, les, drugi materiali (ISO 12215-3:2002)
Ta del standarda ISO 12215 določa zahteve za materiale, namenjene za uporabo pri izdelavi trupa, nadkonstrukcije in dodatkov, zlasti za:
– varivno običajno in vroče valjano pločevino, široke plošče, profile in palice;
– avstenitna nerjavna jekla, izdelana v obliki plošč ali profilov;
– gnetene aluminijeve zlitine, izdelane kot plošče, profili in ekstrudirani profili;
– les v obliki masivnega lesa, vezanih plošč ali furnirja;
– druge ustrezne materiale.
OPOMBA 1: Pri konstrukciji malih plovil se lahko uporabljajo drugi materiali, če je mogoče dokazati primerno ustreznost in trajnost za predvideni namen.
Ta del standarda ISO 12215 se uporablja za mala plovila z dolžino trupa (LH) do 24 m v skladu s standardom ISO 8666.
OPOMBA 2: Osnovni razlog za pripravo tega dela standarda ISO 12215 je, da izbira materialov za konstrukcijo malega plovila pomembno vpliva na kratkoročno in dolgoročno vzdržljivost v skladu s pričakovanimi obremenitvami ter okoljskimi pogoji.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 12215-3:2002
Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 3. del: Materiali: jeklo,
aluminijeve zlitine, les, drugi materiali (ISO 12215-3:2002)
Small craft - Hull construction and scantlings - Part 3: Materials: Steel, aluminium alloys,
wood, other materials (ISO 12215-3:2002)
Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 3: Werkstoffe:
Stahl, Aluminiumlegierungen, Holz, andere Werkstoffe (ISO 12215-3:2002)
Petits navires - Construction de coques et échantillons - Partie 3: Matériaux: Acier,
alliages d'aluminium, bois, autres matériaux (ISO 12215-3:2002)
Ta slovenski standard je istoveten z: EN ISO 12215-3:2018
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 12215-3
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 12215-3:2002
English Version
Small craft - Hull construction and scantlings - Part 3:
Materials: Steel, aluminium alloys, wood, other materials
(ISO 12215-3:2002)
Petits navires - Construction de coques et échantillons - Kleine Wasserfahrzeuge - Rumpfbauweise und
Partie 3: Matériaux: Acier, alliages d'aluminium, bois, Dimensionierung - Teil 3: Werkstoffe: Stahl,
autres matériaux (ISO 12215-3:2002) Aluminiumlegierungen, Holz, andere Werkstoffe (ISO
12215-3:2002)
This European Standard was approved by CEN on 16 April 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12215-3:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4
European foreword
The text of ISO 12215-3:2002 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 12215-3:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall be
withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12215-3:2002.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 12215-3:2002 has been approved by CEN as EN ISO 12215-3:2018 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2013/53/EU
Essential Clause(s)/sub- Remarks/Notes
Requirements of clause(s) of
Directive this EN
2013/53/EU
Annex I, Part A, 3.1 - All clauses This standard addresses the essential requirement set out in
Structure Annex I, Part A, 3.1 in respect of the requirements for steel,
aluminium alloys, wood and other materials used for the
construction of watercraft with the exception of thermosetting
resins, glass fibre reinforcement and reference laminate which
are addressed separately by part 1 of this standard series.
Annex I, Part A, 2.5 – 8, Annex A
Owner’s Manual
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 12215-3
First edition
2002-05-01
Small craft — Hull construction
and scantlings —
Part 3:
Materials: Steel, aluminium alloys, wood,
other materials
Petits navires — Construction de coques et échantillons —
Partie 3: Matériaux: Acier, alliages d'aluminium, bois, autres matériaux
Reference number
ISO 12215-3:2002(E)
©
ISO 2002
ISO 12215-3:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved
ISO 12215-3:2002(E)
Contents Page
Foreword.iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Requirements for metal.2
5 Requirements for wood.4
6 Requirements for other materials .6
7 Documentation.6
8 Owner’s manual.7
Annex A (normative) Information to be provided in the owner's manual .8
Bibliography.9
ISO 12215-3:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 12215 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12215-3 was prepared by Technical Committee ISO/TC 188, Small craft.
ISO 12215 consists of the following parts, under the general title Small craft — Hull construction and scantlings:
— Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate
— Part 2: Materials: Core materials for sandwich construction, embedded materials
— Part 3: Materials: Steel, aluminium alloys, wood, other materials
— Part 4: Workshop and manufacturing
— Part 5: Design pressures, design stresses, scantling determination
— Part 6: Structural arrangements and details
Annex A forms a normative part of this part of ISO 12215.
iv © ISO 2002 – All rights reserved
INTERNATIONAL STANDARD ISO 12215-3:2002(E)
Small craft — Hull construction and scantlings —
Part 3:
Materials: Steel, aluminium alloys, wood, other materials
1 Scope
This part of ISO 12215 specifies requirements for materials intended for use in the construction of the hull,
superstructure and appendages, in particular:
— weldable normal and higher strength hot-rolled steel plates, wide flats, sections and bars;
— austenitic stainless steels, fabricated in the form of plates or profiles;
— wrought aluminium alloys fabricated as plates, sections and extruded profiles;
— wood in the form of solid timber, plywood or veneer;
— other suitable materials.
NOTE 1 Other materials may be used in the construction of small craft if adequate suitability and durability for the intended
purpose can be demonstrated.
This part of ISO 12215 applies to small craft with a length hull (L ) according to ISO 8666 of up to 24 m.
H
NOTE 2 The underlying reason for preparing this part of ISO 12215 is that the choice of materials for the construction of a
small craft has a significant influence on short-term and long-term durability under the expected loads and environmental
conditions.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 12215. For dated references, subsequent amen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.