EN 725-10:2007

Advanced technical ceramics - Methods of test for ceramic powders - Part 10: Determination of compaction properties

This Part of EN 725 describes methods for the determination of the compaction behaviour of ungranulated or granulated ceramic powders, when subjected to uniaxial compressive loading in a rigid die, under specified conditions.

Hochleistungskeramik - Prüfverfahren für keramische Pulver - Teil 10: Bestimmung der Verdichtungseigenschaften

Dieser Teil von EN 725 beschreibt Verfahren für die Ermittlung des Verdichtungsverhaltens von nicht granu¬lierten oder granulierten keramischen Pulvern bei uniaxialer Druckbelastung in einer formstabilen Matrize unter festgelegten Bedingungen.

Céramiques techniques avancées - Méthodes d'essai des poudres céramiques - Partie 10: Détermination des propriétés de compaction

La présente partie de l’EN 725 décrit des méthodes permettant de déterminer le taux de compactage d’une poudre céramique, granulée ou non, lorsqu’elle est soumise à une charge de compression uniaxiale dans une matrice de confinement, dans des conditions spécifiées.

Sodobna tehnična keramika - Preskusne metode za keramične praške - 10. del: Ugotavljanje lastnosti za stiskanje

General Information

• Status: Withdrawn
• Publication Date: 11-Sep-2007
• Withdrawal Date: 19-Jan-2021
• ICS: 81.060.30 - Advanced ceramics
• Technical Committee: CEN/TC 184 - Advanced technical ceramics
• Drafting Committee: CEN/TC 184/WG 2 - Methods of test for ceramic powders
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 20-Jan-2021
• Mandate: M/BC/CEN/90/4 - Request concerning the realisation of a standardization programme in the field of advanced technical ceramics
• Ref Project: SIST EN 725-10:2008 - Advanced technical ceramics - Methods of test for ceramic powders - Part 10: Determination of compaction properties

Relations

• Replaces: EN 725-10:1997 - Advanced technical ceramics - Methods of test for ceramic powders - Part 10: Determination of compaction properties
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 17172:2021 - Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of compaction properties of ceramic powders (ISO 17172:2014)
• Effective Date: 27-Oct-2021

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 725-10:2008
01-marec-2008
1DGRPHãþD
SIST EN 725-10:2000
6RGREQDWHKQLþQDNHUDPLND3UHVNXVQHPHWRGH]DNHUDPLþQHSUDãNHGHO
8JRWDYOMDQMHODVWQRVWL]DVWLVNDQMH
Advanced technical ceramics - Methods of test for ceramic powders - Part 10:
Determination of compaction properties
Hochleistungskeramik - Prüfverfahren für keramische Pulver - Teil 10: Bestimmung der
Verdichtungseigenschaften
Céramiques techniques avancées - Méthodes d'essai pour poudres céramiques - Partie
10: Détermination des propriétés de compaction
Ta slovenski standard je istoveten z: EN 725-10:2007
ICS:
81.060.30
SIST EN 725-10:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 725-10
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2007
ICS 81.060.30 Supersedes EN 725-10:1997
English Version
Advanced technical ceramics - Methods of test for ceramic
powders - Part 10: Determination of compaction properties
Céramiques techniques avancées - Méthodes d'essai des Hochleistungskeramik - Prüfverfahren für keramische
poudres céramiques - Partie 10: Détermination des Pulver - Teil 10: Bestimmung der
propriétés de compaction Verdichtungseigenschaften
This European Standard was approved by CEN on 11 August 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 725-10:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 725-10:2007 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Principle.4
4 Symbols .4
5 Apparatus .4
6 Procedure .5
6.1 Drying.5
6.2 Quantity .5
6.3 Cleaning of the die and punches .5
6.4 Powder testing conditions.5
6.5 Lubrication .5
6.6 Compacting pressures.6
6.7 Compacting and ejection .6
7 Expression of results .
...