EN ISO 16890-2:2016

Air filters for general ventilation - Part 2: Measurement of fractional efficiency and air flow resistance (ISO 16890-2:2016)

ISO 16890-2:2016 specifies the aerosol production, the test equipment and the test methods used for measuring fractional efficiency and air flow resistance of air filters for general ventilation.
It is intended for use in conjunction with ISO 16890‑1, ISO 16890‑3 and ISO 16890‑4.
The test method described in this part of ISO 16890 is applicable for air flow rates between 0,25 m3/s (900 m3/h, 530 ft3/min) and 1,5 m3/s (5 400 m3/h, 3 178 ft3/min), referring to a test rig with a nominal face area of 610 mm × 610 mm (24,0 inch × 24,0 inch).
ISO 16890 (all parts) refers to particulate air filter elements for general ventilation having an ePM1 efficiency less than or equal to 99 % and an ePM10 efficiency greater than 20 % when tested as per the procedures defined within ISO 16890 (all parts).
NOTE          The lower limit for this test procedure is set at a minimum ePM10 efficiency of 20 % since it will be very difficult for a test filter element below this level to meet the statistical validity requirements of this procedure.
Air filter elements outside of this aerosol fraction are evaluated by other applicable test methods, (see ISO 29463 (all parts)).
Filter elements used in portable room-air cleaners are excluded from the scope.
The performance results obtained in accordance with ISO 16890 (all parts) cannot by themselves be quantitatively applied to predict performance in service with regard to efficiency and lifetime.

Luftfilter für die allgemeine Raumlufttechnik - Teil 2: Ermittlung des Franktionsabscheidegrades und des Durchflusswiderstandes (ISO 16890-2:2016)

Filtres à air de ventilation générale - Partie 2: Mesurage de l'efficacité spectrale et de la résistance à l'écoulement de l'air (ISO 16890-2:2016)

ISO 16890-2:2016 spécifie la production d'aérosol, l'équipement d'essai et les méthodes d'essai utilisés pour mesurer l'efficacité spectrale et la résistance à l'écoulement de l'air d'un filtre à air de ventilation générale.
Elle est destinée à être utilisée conjointement avec l'ISO 16890‑1, l'ISO 16890‑3 et l'ISO 16890‑4.
La méthode d'essai décrite dans la présente partie de l'ISO 16890 est applicable pour des débits d'air compris entre 0,25 m3/s (900 m3/h, 530 ft3/min) et 1,5 m3/s (5400 m3/h, 3178 ft3/min), en se référant à un banc d'essai ayant une surface frontale nominale de 610 mm x 610 mm (24 inch x 24 inch).
L'ISO 16890 (toutes les parties) concerne les éléments filtrants de ventilation générale ayant une efficacité ePM1 inférieure ou égale à 99 % et une efficacité ePM10 supérieure à 20 %, lorsqu'ils sont soumis à essai selon les modes opératoires définis dans l'ISO 16890 (toutes les parties).
NOTE          Pour ce mode opératoire, la limite inférieure est fixée à une efficacité minimale ePM10 de 20 % étant donné qu'il est très difficile pour un élément filtrant d'essai, en dessous de ce niveau, de respecter les exigences de validité statistique de ce mode opératoire.
En dehors de ces fractions d'aérosol, les éléments filtrant sont évalués par d'autres méthodes d'essai applicables (voir l'ISO 29463 (toutes les parties)).
Les éléments filtrants utilisés dans les épurateurs d'air ambiant portatifs sont exclus du domaine d'application.
Les résultats de performance obtenus conformément à l'ISO 29463 (toutes les parties) ne peuvent pas être utilisés quantitativement pour prédire les performances en service, en ce qui concerne l'efficacité et la durée de vie.

Zračni filtri pri splošnem prezračevanju - 2. del: Merjenje frakcijske učinkovitosti in odpornosti proti toku zraka (ISO 16890-2:2016)

Ta evropski standard se uporablja za zračne filtre delcev za splošno prezračevanje, katerih začetna učinkovitost v zvezi z delci velikosti 0,4 μm je manj kot 99 %. Filtri, ki se uporabljajo pri prezračevanju nizkih stanovanjskih stavb ali premični čistilniki zraka v prostorih so izključeni s področja uporabe tega standarda. Opisuje tehnične specifikacije, zahteve in metodo preskušanja za merjenje frakcijske učinkovitosti in odpornosti proti toku zraka. Metoda je uporabna za tok zraka med 0,25 m³/s (900 m³/h, 530 ft³/min) in 1,5 m³/s (5400 m³/h, 3178 ft³/min) v preskusnih ceveh z nazivno površino 0,61 m x 0,61 m. Boljši filtri z začetno učinkovitostjo nad 99 % glede na delce velikosti 0,4 µm se preskušajo in razvrščajo v skladu z drugimi standardi (glej ISO 29463, del 1-5). Filtri v skladu s to serijo standardov se ocenjujejo po njihovi učinkovitosti odstranjevanja delcev aerosolov PM10, PM2.5 in PM1. Učinkovitost zbiranja delcev vložka filtra se meri kot funkcija velikosti delcev v razponu od 0,3 do 10 μm pri praznem in nekondicioniranem vložku filtra. V drugem koraku je treba polni vložek filtra kondicionirati (izprazniti) v koraku umetnega staranja, s čimer se zagotovijo informacije o intenzivnosti elektrostatičnega mehanizma odstranjevanja. Rezultati drugega koraka se uporabljajo za izračun povprečne učinkovitosti v razponih velikosti PM10, PM2.5 in PM1 s ponderiranjem vrednosti frakcijske učinkovitosti glede na porazdelitev standardizirane in normalizirane velikosti delcev povezane frakcije zunanjega aerosola. V tem standardu je določena ta porazdelitev standardizirane in normalizirane velikosti delcev.

General Information

• Status: Withdrawn
• Publication Date: 13-Dec-2016
• Withdrawal Date: 30-Aug-2022
• ICS: 91.140.30 - Ventilation and air-conditioning systems
• Technical Committee: CEN/TC 195 - Air filters for general air cleaning
• Drafting Committee: CEN/TC 195/WG 1 - Particulate air filters for general ventilation
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 31-Aug-2022
• Directive: 1253/2014 - Commission Regulation (EU) No 1253/2014 of 7 July 2014 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for ventilation units
• Directive: 1254/2014 - Commission Delegated Regulation (EU) No 1254/2014 of 11 July 2014 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to energy labelling of residential ventilation units
• Mandate: M/537 - [C2015)8325] Standardisation request to the European Committee for Standardisation as regards ventilation units in support of Regulation (EU) No 1253/2014 and Delegated Regulation (EU) No 1254/2014
• Ref Project: SIST EN ISO 16890-2:2017 - Air filters for general ventilation - Part 2: Measurement of fractional efficiency and air flow resistance (ISO 16890-2:2016)

Relations

• Replaces: EN 779:2012 - Particulate air filters for general ventilation - Determination of the filtration performance
• Effective Date: 08-Jun-2022
• Replaced By: EN ISO 16890-2:2022 - Air filters for general ventilation - Part 2: Measurement of fractional efficiency and air flow resistance (ISO 16890-2:2022)
• Effective Date: 07-Sep-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2017
1DGRPHãþD
SIST EN 779:2012
=UDþQLILOWULSULVSORãQHPSUH]UDþHYDQMXGHO0HUMHQMHIUDNFLMVNHXþLQNRYLWRVWLLQ
RGSRUQRVWLSURWLWRNX]UDND,62
Air filters for general ventilation - Part 2: Measurement of fractional efficiency and air flow
resistance (ISO 16890-2:2016)
Luftfilter für die allgemeine Raumlufttechnik - Teil 2: Ermittlung des
Franktionsabscheidegrades und des Durchflusswiderstandes (ISO 16890-2:2016)
Filtres à air pour ventilation générale - Partie 2: Mesurage du rendement fractionnaire et
de la résistance à l'écoulement de l'air (ISO 16890-2:2016)
Ta slovenski standard je istoveten z: EN ISO 16890-2:2016
ICS:
91.140.30 3UH]UDþHYDOQLLQNOLPDWVNL Ventilation and air-
VLVWHPL conditioning systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 16890-2
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2016
EUROPÄISCHE NORM
ICS 91.140.30 Supersedes EN 779:2012
English Version
Air filters for general ventilation - Part 2: Measurement of
fractional efficiency and air flow resistance (ISO 16890-
2:2016)
Filtres à air de ventilation générale - Partie 2: Luftfilter für die allgemeine Raumlufttechnik - Teil 2:
Mesurage de l'efficacité spectrale et de la résistance à Ermittlung des Franktionsabscheidegrades und des
l'écoulement de l'air (ISO 16890-2:2016) Durchflusswiderstandes (ISO 16890-2:2016)
This European Standard was approved by CEN on 19 September 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16890-2:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 16890-2:2016) has been prepared by Technical Committee ISO/TC 142
"Cleaning equipment for air and other gases" in collaboration with Technical Committee CEN/TC 195
“Air filters for general air cleaning” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2017, and conflicting national standards shall be
withdrawn at the latest by June 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 779:2012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16890-2:2016 has been approved by CEN as EN ISO 16890-2:2016 without any
modification.
INTERNATIONAL ISO
STANDARD 16890-2
First edition
2016-12-01
Air filters for general ventilation —
Part 2:
Measurement of fractional efficiency
and air flow resistance
Filtres à air de ventilation générale —
Partie 2: Mesurage de l’efficacité spectrale et de la résistance à
l’écoulement de l’air
Reference number
ISO 16890-2:2016(E)
©
ISO 2016
ISO 16890-2:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 16890-2:2016(E)
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 4
4.1 Symbols . 4
4.2 Abbreviated terms . 6
5 General test requirements . 6
5.1 Test device requirements . 6
5.2 Test device installation . 6
5.3 Test rig requirements . 6
6 Test materials . 7
6.1 Liquid phase aerosol . 7
6.1.1 DEHS test aerosol . 7
6.1.2 DEHS/DES/DOS - formula . 7
6.1.3 DEHS properties . 7
6.1.4 Liquid phase aerosol generation . 7
6.2 Solid phase aerosol . 8
6.2.1 Potassium chloride (KCl) test aerosol . 8
6.2.2 KCl - formula . 8
6.2.3 KCl properties . 8
6.2.4 Solid phase aerosol generation . 9
6.3 Reference aerosols .10
6.3.1 Reference aerosol for 0,3 µm to 1,0 µm .10
6.3.2 Reference aerosol for 1,0 µm to 10,0 µm .10
6.3.3 Other reference aerosols .10
6.3.4 Matching criteria .11
6.4 Aerosol loading .11
7 Test equipment.11
7.1 Test rig .11
7.1.1 Dimensions .11
7.1.2 Construction materials .12
7.1.3 Test rig shape .12
7.1.4 Test rig air supply .13
7.1.5 Test rig isolation .13
7.1.6 D/S mixing orifice .13
7.1.7 Aerosol sampling .14
7.1.8 Test rig air flow rate measurement . .16
7.1.9 Resistance to air flow measurement .16
7.1.10 Non 610 mm × 610 mm (24,0 inch × 24,0 inch) test devices .17
7.1.11 Dust injection testing .18
7.2 Aerosol particle counter .18
7.2.1 General.18
7.2.2 OPC sampled size range .
...