Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines

This document specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to manually loaded and unloaded vertical panel sawing (with or without integrated feed) machines fitted with:
-   the facility for scoring;
-   an angle cutting device;
-   a middle support device;
-   a programmable stop for parallel vertical cuts;
-   the facility for grooving with a width of at most 20 mm in one pass by using a milling tools,
hereinafter referred to as "machines" when they are used as intended and under the conditions foreseen by the manufacturer.
The machines are designed for cutting panels of the following materials:
a)   wood based materials such as chipboard, fibreboard, plywood and also these materials where they are covered with plastic / light alloy laminates;
b)   solid wood;
c)   hardened rubber and hardened plastic material;
d)   non ferrous materials e.g. light alloy;
e)   compound materials with core consisting of polyurethane or mineral material laminated with light alloy.
This document does not apply to vertical panel saws with pressure beam and saw unit mounted behind the workpiece support.
This document does not deal with hazards relating to the combination of a single machine being used with any other machine (as part of a line).
This document is not applicable to vertical panel saws which are manufactured before the date of its publication as EN.
NOTE   Machines covered by this standard are listed under A.1.4 of annex IV of the Machinery Directive.

Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 14: Vertikalplattenkreissägemaschinen

Dieses Dokument spezifiziert alle signifikanten Gefährdungen, Gefährdungssituationen und Gefähr-dungsereignisse, wie sie in Abschnitt 4 aufgelistet sind, und die auf Vertikalplattenkreissägemaschinen mit Hand¬beschickung und Handentnahme (mit oder ohne mechanischen Vorschub), die ausgerüstet sind mit:
-   einer Einrichtung zum Ritzsägen;
-   einer Winkelschnitteinrichtung;
-   einer Mittenauflage;
-   einem programmierbarer Anschlag für vertikale Parallelschnitte;
-   einer Einrichtung zum Nuten in einem Durchgang unter Verwendung von Fräswerkzeugen mit einer Breite von höchstens 20 mm,
im Folgenden als „Maschinen“ bezeichnet — zutreffen, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers verwendet werden.
Die Maschinen sind bestimmt zum Schneiden von Platten, die aus folgenden Materialien bestehen:
a)   Holzwerkstoffe wie Spanplatten, Faserplatten und Sperrholz, sowie diesen Werkstoffen, wenn sie mit Kunststoff- oder Leichtmetall-Laminat beschichtet sind;
b)   Massivholz;
c)   Hartgummi und Hartkunststoff;
d)   Nichteisenmetalle, z. B. Leichtmetall-Legierung;
e)   Verbundwerkstoffe mit einem aus Polyurethan oder mineralischem Material bestehenden Kern, der mit Leichtmetall-Legierung laminiert ist.
Dieses Dokument gilt nicht für Vertikalplattenkreissägemaschinen mit Druckbalken, bei denen das Säge-aggregat hinter der Werkstückauflage angeordnet ist.
Dieses Dokument behandelt nicht spezielle Gefährdungen im Zusammenhang mit der Kombination einer einzelnen Maschine mit irgendeiner anderen Maschine (als Teil einer Linie).
Dieses Dokument gilt nicht für Vertikalplattenkreissägemaschinen, die vor dem Datum seiner Veröffentlichung durch CEN hergestellt wurden.
ANMERKUNG   Die in diesem Dokument behandelten Maschinen sind unter A.1.4 des Anhangs IV der Maschinen¬richtlinie genannt.

Sécurité des machines pour le travail du bois - Machines à scie circulaire - Partie 14: Scies à panneaux verticales

Le présent document !spécifie tous les" phénomènes dangereux, des situations et événements dangereux tels qu’énumérés à l’Article 4, applicables aux scies à panneaux verticales à chargement et déchargement manuel (avec ou sans avance intégrée) équipées :
   de la possibilité d’incision ;
   d’un dispositif de coupe en angle ;
   d’un support intermédiaire ;
   d’une butée programmable pour les coupes verticales parallèles ;
   de la possibilité d’utiliser des outils de fraisage pour réaliser des rainures d'une largeur d'au plus 20 mm en une passe.
désignées ci-après sous le terme «machines», durant l’utilisation normale et dans les conditions prévues par le fabricant.
Les machines sont conçues pour découper des panneaux :
a)   en matériaux à base de bois tels que des panneaux de fibres ou de particules, de contreplaqué ainsi que ces matériaux lorsqu'ils sont recouverts de plastique ou d'alliages légers ;
b)   en bois massif ;
c)   en caoutchouc durci et matériaux plastiques rigides ;
d)   en matériaux en alliages non ferreux, par exemple alliages légers ;
e)   en matériaux composites à âme en polyuréthane ou en matières minérales recouverts d’alliages légers.
Le présent document n’est pas applicable aux scies à panneaux verticales à presseur et unité de sciage montés derrière le support de pièce.
Le présent document ne traite pas des phénomènes dangereux relatifs à la combinaison d’une machine isolée utilisée avec toute autre machine (comme faisant partie d’une ligne).
Le présent document n’est pas applicable aux scies à panneaux verticales fabriquées avant la date de sa publication comme EN.
NOTE   Les machines à avance intégrée couvertes par le présent document figurent dans l’Annexe IV, A.1.4, de la Directive «Machines».

Varnost lesnoobdelovalnih strojev - Krožne žage - 14. del: Vertikalni krožni žagalni stroji

General Information

Status
Withdrawn
Publication Date
13-Oct-2009
Withdrawal Date
13-Mar-2012
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
14-Mar-2012
Completion Date
14-Mar-2012

Relations

Buy Standard

Standard
EN 1870-14:2008+A1:2009
English language
61 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1870-14:2008+A1:2009
01-december-2009
Varnost lesnoobdelovalnih strojev - Krožne žage - 14. del: Vertikalni krožni žagalni
stroji
Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel
sawing machines
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 14:
Vertikalplattenkreissägemaschinen
Sécurité des machines pour le travail du bois - Machines à scier circulaires - Partie 14:
Scies à panneaux verticales
Ta slovenski standard je istoveten z: EN 1870-14:2007+A1:2009
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870-14:2008+A1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1870-14:2008+A1:2009

---------------------- Page: 2 ----------------------

SIST EN 1870-14:2008+A1:2009


EUROPEAN STANDARD
EN 1870-14:2007+A1

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2009
ICS 79.120.10 Supersedes EN 1870-14:2007
English Version
Safety of woodworking machines - Circular sawing machines -
Part 14: Vertical panel sawing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scier circulaires - Partie 14: Scies à panneaux verticales Kreissägemaschinen - Teil 14:
Vertikalplattenkreissägemaschinen
This European Standard was approved by CEN on 22 November 2007 and includes Amendment 1 approved by CEN on 20 August 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-14:2007+A1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1870-14:2008+A1:2009
EN 1870-14:2007+A1:2009 (E)
Contents Page
Foreword .4
Introduction .6
1 Scope .6
2 Normative references .7
3 Terms and definitions .9
4 List of significant hazards . 13
5 Safety requirements and / or measures . 16
5.1 General . 16
5.2 Controls . 16
5.2.1 Safety and reliability of control systems . 16
5.2.2 Position of controls . 17
5.2.3 Starting . 17
5.2.4 Normal stopping .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.