EN ISO 13669:2025
(Main)Fasteners - Grooved pins - General requirements (ISO 13669:2025)
Fasteners - Grooved pins - General requirements (ISO 13669:2025)
This document specifies the general characteristics of grooved pins, made of steel and stainless steel, with nominal diameters 1 mm to 25 mm.
These grooved pins are designed to fulfil the main following functions, due to the elastic fit behaviour of the grooves:
— locking of two (or more) parts,
— positioning or guiding,
— relative rotation of the assembled parts.
Verbindungselemente - Kerbstifte - Allgemeine Anforderungen (ISO 13669:2025)
Dieses Dokument legt die allgemeinen Eigenschaften von Kerbstiften aus Stahl und nichtrostendem Stahl mit Nenndurchmessern zwischen 1 mm und 25 mm fest.
Diese Kerbstifte sind aufgrund des elastischen Passverhaltens der Kerben dafür ausgelegt, die folgenden Hauptfunktionen zu übernehmen:
kraftschlüssiges Verbinden von zwei (oder mehr) Teilen,
Positionieren oder Führen,
relative Drehung der zusammengefügten Teile.
Fixations - Goupilles cannelées - Exigences générales (ISO 13669:2025)
Le présent document spécifie les caractéristiques générales des goupilles cannelées, en acier et en acier inoxydable, de diamètre nominal de 1 mm à 25 mm.
Ces goupilles cannelées sont conçues pour remplir les principales fonctions suivantes, grâce au comportement d’ajustement élastique des cannelures:
— solidarisation de deux (ou plusieurs) pièces,
— positionnement ou guidage,
— rotation relative (articulation) entre les pièces assemblées.
Vezni elementi - Zasekani zatiči z utori - Splošne zahteve (ISO 13669:2025)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 13669:2024
01-februar-2024
Vezni elementi - Zasekani zatiči z utori - Splošne zahteve (ISO/DIS 13669:2023)
Fasteners - Grooved pins - General requirements (ISO/DIS 13669:2023)
Verbindungselemente - Kerbstifte - Allgemeine Anforderungen (ISO/DIS 13669:2023)
Fixations - Goupilles cannelées - Exigences générales (ISO/DIS 13669:2023)
Ta slovenski standard je istoveten z: prEN ISO 13669
ICS:
21.060.50 Zatiči, žeblji Pins, nails
oSIST prEN ISO 13669:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 13669:2024
oSIST prEN ISO 13669:2024
DRAFT INTERNATIONAL STANDARD
ISO/DIS 13669
ISO/TC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-11-30 2024-02-22
Fasteners — Grooved pins — General requirements
Fixations — Goupilles cannelées — Exigences générales
ICS: 21.060.50
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 13669:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 13669:2024
ISO/DIS 13669:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 13669
ISO/TC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
Fasteners — Grooved pins — General requirements
Fixations — Goupilles cannelées — Exigences générales
ICS: 21.060.50
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 13669:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 13669:2024
ISO/DIS 13669:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Shapes and ends for grooved pins .2
4.1 Ends for grooved pins . 2
4.2 Groove ends . 2
4.3 Groove shapes . 3
4.3.1 Diamond groove (symbol D) . 3
4.3.2 oval groove (symbol O) . 3
4.3.3 progressive groove (symbol P) . 3
5 Principles for grooved pins and assembly . 3
5.1 Principles for grooved pins . 3
5.2 Assembly . 4
6 Dimensions and tolerances .5
6.1 General . 5
6.2 Expanded diameter d and control method . 5
6.3 Pin straightness . 6
7 Mechanical and physical properties . 7
7.1 General . 7
7.2 Shear resistance . 7
7.3 Hardness . 8
7.4 Pins in materials other than non-heat treated steel or stainless steel . 9
8 Inspection . 9
8.1 Manufacturer's inspection . 9
8.2 Supplier's inspection . 10
8.3 Purchaser's inspection . 10
8.4 Delivery of test results . 10
9 Marking and labelling .10
9.1 Marking on grooved pins . 10
9.2 Labelling on packages . 10
Annex A (informative) Control of straightness for grooved pins.11
Bibliography .16
iii
oSIST prEN ISO 13669:2024
ISO/DIS 13669:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners and by Technical Committee
CEN/TC 185, Fasteners in collaboration.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
oSIST prEN ISO 13669:2024
DRAFT INTERNATIONAL STANDARD ISO/DIS 13669:2023(E)
Fasteners — Grooved pins — General requirements
1 Scope
This document specifies the general characteristics of grooved pins, made of steel and stainless steel,
with nominal diameters 1 mm to 25 mm.
These grooved pins are designed to fulfil the main following functions, due to the elastic fit behavior of
the grooves:
— locking of two (or more) parts,
— positioning or guiding,
— relative rotation of the assembled parts.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1891-4, Fasteners — Vocabulary — Part 4: Control, inspection, delivery, acceptance and quality
ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method
ISO 8749, Pins and grooved pins — Shear test
ISO 16228, Fasteners — Types of inspection documents
ISO 16426, Fasteners — Quality assurance system
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
pin
cylindrical or conical shafted fastener designed to be fitted into a hole, which provides functions such
as immobilization by locking parts together, positioning, rotation and/or guiding
3.2
groove [for a pin]
longitudinal indentation into the material of the pin forming two protruding lips along the side of the
groove
oSIST prEN ISO 13669:2024
ISO/DIS 13669:2023(E)
3.3
grooved pin
fastener whose shaft presents three grooves at equidistant 120° intervals resulting in the expanded
diameter, which are compressed when the pin is inserted into a hole smaller than the expanded diameter
but greater than the pin nominal diameter, thus achieving an elastic locking due to interference fit
between this expanded
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.