EN ISO 13337:2009

Spring-type straight pins - Slotted, light duty (ISO 13337:2009)

ISO 13337:2009 specifies the characteristics of slotted spring-type straight pins, made of steel or of austenitic or martensitic stainless steel, light duty, with nominal diameter from 2 mm to 50 mm inclusive.

Spannstifte (-hülsen) - Geschlitzt, leichte Ausführung (ISO 13337:2009)

Diese Internationale Norm legt die Eigenschaften von geschlitzten Spannstiften ( hülsen) aus Stahl oder aus austenitischem bzw. martensitischem nichtrostenden Stahl in leichter Ausführung mit einem Nenndurch-messer d1 von 2 mm bis einschließlich 50 mm fest.
ANMERKUNG   Die Nenndurchmesser wurden so gewählt, dass die Spannstifte ineinander geschoben oder mit Spann¬stiften in schwerer Ausführung nach ISO 8752 verbunden werden können.

Goupilles cylindriques creuses, dites goupilles élastiques - Série mince (ISO 13337:2009)

L'ISO 13337:2009 spécifie les caractéristiques des goupilles cylindriques creuses, dites goupilles élastiques, en acier ou en acier inoxydable austénitique ou martensitique, série mince, de diamètre nominal compris entre 2 mm et 50 mm inclus.

Valjasto zviti vzmetni zatiči - Lahka izvedba (ISO 13337:2009)

Ta mednarodni standard določa značilnosti valjasto zvitih vzmetnih zatičev, izdelanih iz jekla ali iz avstenitnega ali martenzitnega nerjavečega jekla, lahke izvedbe, z nominalnim premerom, d1, od 2 mm do vključno 50 mm.

General Information

• Status: Published
• Publication Date: 14-Jun-2009
• Withdrawal Date: 30-Dec-2009
• ICS: 21.060.50 - Pins, nails
• Technical Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Drafting Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 15-Jun-2009
• Completion Date: 15-Jun-2009
• Ref Project: SIST EN ISO 13337:2012 - Spring-type straight pins - Slotted, light duty (ISO 13337:2009)

Relations

• Replaces: EN ISO 13337:1997 - Spring-type straight pins - Slotted, light duty (ISO 13337:1997)
• Effective Date: 08-Jun-2022

Overview

EN ISO 13337:2009 provides the international standard specification for spring-type straight pins - slotted, light duty. These pins are made from steel, austenitic stainless steel, or martensitic stainless steel, and cover nominal diameters from 2 mm up to 50 mm inclusive. Developed by ISO/TC 2 and endorsed by CEN, this standard supersedes the earlier 1997 edition to offer updated technical and dimensional requirements. It is essential for manufacturers, suppliers, and users involved in fastener components, ensuring consistent quality, interchangeability, and performance across industries.

Key Topics

• Pin Materials
  The standard stipulates the use of steel, austenitic stainless steel, or martensitic stainless steel, detailing chemical composition limits and hardness requirements. Heat treatments such as hardening and tempering ensure durability and shear strength.

• Dimensional Specifications
  Covers nominal diameters (2 mm to 50 mm), lengths, and slot dimensions required for light-duty spring pins. Tolerances are defined according to the hole tolerances (H12 class) to ensure proper fitting without the slot fully closing upon installation.

• Mechanical Properties
  Includes minimum double shear strength values for steel and martensitic stainless pins. Austenitic stainless steel pins do not have specified shear strength values.

• Surface Finishes and Coatings
  The standard advises against certain coatings like electroplating or phosphate-coating without proper baking processes to mitigate hydrogen embrittlement. Alternative corrosion protection methods may be applied as agreed between the customer and supplier.

• Testing and Acceptance
  Hardness tests must comply with ISO 6507-1; shear strength is tested as per ISO 8749. Acceptance inspection follows ISO 3269 guidelines. The workmanship requires pins to be free from defects and burrs.

• Designation System
  Provides examples for marking pins based on diameter, length, type (standard or non-interlocking), and material, facilitating clear identification and specification communication.

Applications

EN ISO 13337:2009 standard spring-type straight pins are widely used for:

• Mechanical Assembly and Fastening
  Ideal for securing components requiring light-duty positioning and retaining, such as in machinery, automotive parts, and appliances.

• Precision Engineering
  Utilized where reliable spring action and alignment are critical, especially in tooling, fixtures, and precision instruments.

• Corrosion-Resistant Environments
  Austenitic and martensitic stainless steel pins conforming to this standard are suitable for applications exposed to moisture or corrosive agents, including marine and food processing equipment.

• Interchangeable Components
  Standardized dimensions and material specifications allow for seamless interchangeability across manufacturers and suppliers, reducing downtimes and facilitating maintenance.

Related Standards

• ISO 8752: For spring-type straight pins - slotted, heavy duty, complementing the specifications for more robust applications.

• ISO 3269: Fasteners - Acceptance inspection, which outlines acceptance procedures applicable to pins defined under this standard.

• ISO 4042: Fasteners - Electroplated coatings, providing guidance on surface treatments and limitations, relevant for corrosion protection measures in spring pins.

• ISO 6507-1: Metallic materials - Vickers hardness test, specifying the hardness test methods referenced in pin qualification.

• ISO 8749: Pins and grooved pins - Shear test, defining the shear strength testing method for pins under light-duty conditions.

---

Keywords

Spring-type straight pins, slotted pins, light duty pins, steel spring pins, stainless steel pins, martensitic stainless steel, austenitic stainless steel, pin dimensions, shear strength, fastener standards, ISO 13337, CEN standards, mechanical fasteners, corrosion resistant pins, precision engineering pins.

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Spannstifte (-hülsen) - Geschlitzt, leichte Ausführung (ISO 13337:2009)Goupilles cylindriques creuses, dites goupilles élastiques - Série mince (ISO 13337:2009)Spring-type straight pins - Slotted, light duty (ISO 13337:2009)21.060.50Pins, nailsICS:Ta slovenski standard je istoveten z:EN ISO 13337:2009SIST EN ISO 13337:2012en,fr,de01-januar-2012SIST EN ISO 13337:2012SLOVENSKI
STANDARDSIST EN ISO 13337:20011DGRPHãþD

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 13337June 2009ICS 21.060.50Supersedes EN ISO 13337:1997
English VersionSpring-type straight pins - Slotted, light duty (ISO 13337:2009)Goupilles cylindriques creuses, dites goupilles élastiques -Série mince (ISO 13337:2009)Spannstifte (-hülsen) - Geschlitzt, leichte Ausführung (ISO13337:2009)This European Standard was approved by CEN on 6 June 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 13337:2009: ESIST EN ISO 13337:2012

Reference numberISO 13337:2009(E)© ISO 2009
INTERNATIONAL STANDARD ISO13337Second edition2009-06-15Spring-type straight pins — Slotted, light duty Goupilles cylindriques creuses, dites goupilles élastiques — Série mince
ISO 13337:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[e-mail] Web
www.iso.org Published in Switzerland
ii © ISO 2009 – All rights reserved
ISO 13337:2009(E) © ISO 2009 – All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13337 was prepared by Technica
...