EN 4811:2017

Aerospace series - Flange couplings - Gasket seal with fluorocarbon seal on aluminium plate with 4 fastening holes - Inch series

This standard specifies the characteristics of gasket seal with fluorocarbon seal on aluminium plate, 4 holes, for pipe couplings for inch series aerospace applications.
Nominal pressure: up to 21 000 kPa; depends on the associated tube material and tube wall thickness in the assembly (see EN 4814).
Temperature range: - 20 °C to 200 °C.
NOTE   Assembly in accordance with TR 4815.
This part should not be reused after disassembling.

Luft- und Raumfahrt - Rohrverschraubung mit Flanschen - Flachdichtung aus Fluorocarbon-Elastomer, mit Aluminiumarmierung mit 4 Befestigungslöchern - Inch-Reihe

Diese Europäische Norm legt die Eigenschaften von Flachdichtungen aus Fluorocarbon-Elastomer mit Aluminiumarmierung mit 4 Löchern für Rohrverbindungen (Inch-Reihe) in Anwendungen der Luft- und Raumfahrt fest.
Nenndruck: Bis zu 21 000 kPa; abhängig von dem Rohrmaterial und der Dicke der Rohrwand bei dem Aufbau (siehe EN 4814).
Temperaturbereich: −20 °C bis 200 °C.
ANMERKUNG   Aufbau nach TR 4815.
Dieser Teil sollte nach der Demontage nicht wieder verwendet werden.

Série aérospatiale - Raccordement à bride - Joint plaque avec joint en fluorocarbone sur plaque en aluminium avec 4 trous de fixation - Série en inches

Aeronavtika - Prirobnične spojke - Robna tesnila z fluoroogljikovimi tesnili na aluminijevi plošči s 4 pritrdilnimi luknjami - Palčne mere

Ta standard določa karakteristike robnega tesnila s fluoroogljikovimi tesnili na aluminijevi plošči s 4 pritrdilnimi luknjami za prirobnične spojke v palčnih merah za aeronavtiko.
Nazivni tlak: do 21.000 kPa, odvisno od materiala povezane cevi, premera cevi in debeline stene cevi v sestavu (glej standard EN 4814).
Temperaturno območje: od −20 °C do 200 °C
OPOMBA Sestav v skladu s TR 4815.
Tega dela se po demontaži naj ne bi znova uporabilo.

General Information

• Status: Published
• Publication Date: 23-May-2017
• Withdrawal Date: 29-Nov-2017
• ICS: 49.080 - Aerospace fluid systems and components
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 24-May-2017
• Completion Date: 24-May-2017
• Ref Project: SIST EN 4811:2017 - Aerospace series - Flange couplings - Gasket seal with fluorocarbon seal on aluminium plate with 4 fastening holes - Inch series

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2017
$HURQDYWLND3ULUREQLþQHVSRMNH5REQDWHVQLOD]IOXRURRJOMLNRYLPLWHVQLOLQD
DOXPLQLMHYLSORãþLVSULWUGLOQLPLOXNQMDPL3DOþQHPHUH
Aerospace series - Flange couplings - Gasket seal with fluorocarbon seal on aluminium
plate with 4 fastening holes - Inch series
Luft- und Raumfahrt - Rohrverschraubung mit Flanschen - Flachdichtung aus
Fluorocarbon-Elastomer, mit Aluminiumarmierung mit 4 Befestigungslöchern - Inch-
Reihe
Série aérospatiale - Raccordement à bride - Joint plaque avec joint en fluorocarbone sur
plaque en aluminium avec 4 trous de fixation - Série en inches
Ta slovenski standard je istoveten z: EN 4811:2017
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
49.025.20 Aluminij Aluminium
49.080 /HWDOVNLLQYHVROMVNL Aerospace fluid systems and
KLGUDYOLþQLVLVWHPLLQGHOL components
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 4811
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2017
EUROPÄISCHE NORM
ICS 49.080
English Version
Aerospace series - Flange couplings - Gasket seal with
fluorocarbon seal on aluminium plate with 4 fastening
holes - Inch series
Série aérospatiale - Raccordement à bride - Joint Luft- und Raumfahrt - Rohrverschraubung mit
plaque avec joint en fluorocarbone sur plaque en Flanschen - Flachdichtung aus Fluorocarbon-
aluminium avec 4 trous de fixation - Série en inches Elastomer, mit Aluminiumarmierung mit 4
Befestigungslöchern - Inch-Reihe
This European Standard was approved by CEN on 14 November 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4811:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Required characteristics . 4
4 Designation . 7
5 Identification marking . 7
6 Technical specification . 7
7 Quality Assurance. 7

European foreword
This document (EN 4811:2017) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2017,
...