EN ISO 4766:2011
(Main)Slotted set screws with flat point (ISO 4766:2011)
Slotted set screws with flat point (ISO 4766:2011)
ISO 4766:2011 specifies the characteristics of slotted set screws with flat point and thread sizes from M1,2 to M12 inclusive and product grade A.
Gewindestifte mit Schlitz und Kegelstumpf (ISO 4766:2011)
Diese Internationale Norm legt die Eigenschaften von Gewindestiften mit Schlitz und Kegelstumpf mit
Gewindegrößen von M1,2 bis einschließlich M12, Produktklasse A, fest.
Werden in besonderen Fällen andere Festlegungen als die in der vorliegenden Internationalen Norm benötigt,
so können diese den bestehenden Internationalen Normen entnommen werden, z. B. ISO 261, ISO 888,
ISO 898-5, ISO 965-2, ISO 3506-3 und ISO 4759-1.
Vis sans tête fendues à bout plat (ISO 4766:2011)
L'ISO 4766:2011 spécifie les caractéristiques des vis sans tête fendues à bout plat, de grade A et de diamètre de filetage M1,2 à M12 inclus.
Navojni zatiči z zarezo in posneto končino (ISO 4766:2011)
Ta mednarodni standard določa značilnosti navojnih zatičev z zarezo in posneto končino od M1,2 do vključno M12 razreda izdelave A. Če so potrebne druge specifikacije, se lahko izberejo med obstoječimi mednarodnimi standardi, na primer ISO 261, ISO 888, ISO 898-5, ISO 965-2, ISO 3506-3 in ISO 4759-1.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gewindestifte mit Schlitz und Kegelstumpf (ISO 4766:2011)Vis sans tête, fendues, à bout plat (ISO 4766:2011)Slotted set screws with flat point (ISO 4766:2011)21.060.10Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:Ta slovenski standard je istoveten z:EN ISO 4766:2011SIST EN ISO 4766:2011en,fr01-oktober-2011SIST EN ISO 4766:2011SLOVENSKI
STANDARDSIST EN 24766:19961DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 4766
August 2011 ICS 21.060.10 Supersedes EN 24766:1992English Version
Slotted set screws with flat point (ISO 4766:2011)
Vis sans tête fendues à bout plat (ISO 4766:2011)
Gewindestifte mit Schlitz und Kegelstumpf (ISO 4766:2011)This European Standard was approved by CEN on 1 July 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4766:2011: ESIST EN ISO 4766:2011
Reference numberISO 4766:2011(E)© ISO 2011
INTERNATIONAL STANDARD ISO4766Second edition2011-08-15Slotted set screws with flat point Vis sans tête fendues à bout plat
ISO 4766:2011(E)
©
ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 4766:2011(E) © ISO 2011 – All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be he
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.