prEN 13892-9
(Main)Methods of test for screed materials - Part 9: Dimensional stability
Methods of test for screed materials - Part 9: Dimensional stability
This document specifies a method for determining the dimensional stability (i.e. the shrinkage and swelling) of cementitious screed, calcium sulphate screed, magnesite screed and synthetic resin screed materials made in accordance with EN 13892-1.
Prüfverfahren für Estrichmörtel und Estrichmassen - Teil 9: Dimensionsstabilität
Dieses Dokument legt ein Verfahren zur Bestimmung der Dimensionsstabilität (d. h. des Schwindens und Quellens) von Zementestrichen, Calciumsulfatestrichen, Magnesiaestrichen und Kunstharzestrichen fest, die in Übereinstimmung mit EN 13892-1 hergestellt wurden.
Méthodes d'essai des matériaux pour chapes - Partie 9 : Stabilité dimensionnelle
Metode preskušanja mešanice za estrih - 9. del: Dimenzijska stabilnost
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 13892-9:2024
01-junij-2024
Metode preskušanja mešanice za estrih - 9. del: Dimenzijska stabilnost
Methods of test for screed materials - Part 9: Dimensional stability
Prüfverfahren für Estrichmörtel und Estrichmassen - Teil 9: Dimensionsstabilität
Méthodes d'essai des matériaux pour chapes - Partie 9 : Stabilité dimensionnelle
Ta slovenski standard je istoveten z: prEN 13892-9
ICS:
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
oSIST prEN 13892-9:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13892-9:2024
---------------------- Page: 2 ----------------------
oSIST prEN 13892-9:2024
DRAFT
EUROPEAN STANDARD
prEN 13892-9
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2024
ICS 91.100.10 Will supersede EN 13892-9:2018
English Version
Methods of test for screed materials - Part 9: Dimensional
stability
Méthodes d'essai des matériaux pour chapes - Partie 9 Prüfverfahren für Estrichmörtel und Estrichmassen -
: Stabilité dimensionnelle Teil 9: Dimensionsstabilität
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 303.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13892-9:2024 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13892-9:2024
prEN 13892-9:2024 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Symbols and abbreviated terms . 4
5 Principle . 4
6 Curling profile apparatus . 5
7 Procedure . 6
7.1 General. 6
7.2 Preparation of specimen . 6
7.3 Length change . 7
7.4 Evaluation of length change .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.