CEN/TS 15963:2010
(Main)Bitumen and bituminous binders - Determination of the fracture toughness temperature by a three point bending test on a notched specimen
Bitumen and bituminous binders - Determination of the fracture toughness temperature by a three point bending test on a notched specimen
This Technical Specification specifies a method for the determination of the Fracture Toughness temperature, TFT, of bituminous binders by means of a three point bending test on a notched binder sample.
WARNING - The use of this Technical Specification can involve hazardous materials, operations and equipment. This Technical Specification does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this Technical Specification to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
Bitumen und bitumenhaltige Bindemittel - Bestimmung der Bruchwiderstandstemperatur mittels eines Drei-Punkt-Biegeversuches an einem gekerbten Probekörper
Diese Technische Spezifikation legt ein Verfahren zur Bestimmung der Bruchwiderstandstemperatur TFT von bitumenhaltigen Bindemitteln mit Hilfe einer Dreipunkt-Biegeprüfung an einem gekerbten Bindemittelprobe-körper fest.
WARNUNG — Die Anwendung dieser Technischen Spezifikation kann den Umgang mit gefährlichen Substanzen und Ausrüstungsteilen und die Ausführung gefährlicher Arbeitsgänge einschließen. Diese Technische Spezifikation erhebt nicht den Anspruch, alle mit ihrer Anwendung verbundenen Sicherheitsprobleme anzusprechen. Es liegt in der Verantwortung des Anwenders dieser Technischen Spezifikation, geeignete Verhaltensregeln zur Sicherheit und Gesundheit festzulegen und die Anwend-barkeit einschränkender Vorschriften vor der Anwendung zu bestimmen.
Bitumes et liants bitumineux - Détermination de la température de résistance à la fissuration par un essai de flexion 3 points sur un barreau entaillé
La présente Spécification Technique spécifie une méthode de détermination de la température de résistance à la fissuration, TFT, des liants bitumineux à l’aide d’un essai de flexion trois points réalisé sur un barreau entaillé. AVERTISSEMENT — L'utilisation de la présente Spécification Technique peut impliquer l'intervention de produits, d'opérations et d'équipements à caractère dangereux. Cette Spécification Technique n'a pas la prétention d'aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de l'utilisateur de cette Spécification Technique de consulter et d'établir des règles de sécurité et d'hygiène appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.
Bitumen in bitumenska veziva - Določanje temperature lomne žilavosti s tritočkovnim upogibnim preskusom
Ta tehnična specifikacija določa metodo za določevanje temperature lomne žilavosti, TFT, bitumenskega veziva s tritočkovnim upogibnim preskusom na zarezanem vezivnem vzorcu.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 15963:2009
01-september-2009
%LWXPHQLQELWXPHQVNDYH]LYD'RORþDQMHWHPSHUDWXUHORPQHåLODYRVWLV
WULWRþNRYQLPXSRJLEQLPSUHVNXVRP
Bitumen and bituminous binders - Determination of the Fracture Toughness temperature
by a notched three point bending test
Bitumes et liants bitumineux - Détermination de la température de résistance à la rupture
par un essai de flexion 3 points sur un barreau entaillé
Ta slovenski standard je istoveten z: FprCEN/TS 15963
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
kSIST-TS FprCEN/TS 15963:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 15963:2009
---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 15963:2009
TECHNICAL SPECIFICATION
FINAL DRAFT
FprCEN/TS 15963
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
June 2009
ICS 91.100.50
English Version
Bitumen and bituminous binders - Determination of the Fracture
Toughness temperature by a notched three point bending test
Bitumes et liants bitumineux - Détermination de la
température de résistance à la rupture par un essai de
flexion 3 points sur un barreau entaillé
This draft Technical Specification is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC
336.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change without notice
and shall not be referred to as a Technical Specification.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 15963:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 15963:2009
FprCEN/TS 15963:2009 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Principle .6
5 Apparatus .6
6 Preparation of test samples .9
7 Procedure to determine the Fracture Toughness temperature T . 12
FT
8 Calculation . 12
9 Expression of results . 13
10 Precision . 14
11 Test report . 15
Annex A (informative) Calculation of Critical Stress Intensity factor . 16
Bibliography . 18
2
---------------------- Page: 4 ----------------------
kSIST-TS FprCEN/TS 15963:2009
FprCEN/TS 15963:2009 (E)
Foreword
This document (FprCEN/TS 15963:2009) has been prepared by Technical Committee CEN/TC 336
“Bituminous binders”, the secretariat of which is held by AFNOR.
This document is currently submitted to the Formal Vote.
3
---------------------- Page: 5 ----------------------
kSIST-TS FprCEN/TS 15963:2009
...
SLOVENSKI STANDARD
SIST-TS CEN/TS 15963:2010
01-april-2010
%LWXPHQLQELWXPHQVNDYH]LYD'RORþDQMHWHPSHUDWXUHORPQHåLODYRVWLV
WULWRþNRYQLPXSRJLEQLPSUHVNXVRP
Bitumen and bituminous binders - Determination of the fracture toughness temperature
by a three point bending test on a notched specimen
Bitumen und bitumenhaltige Bindemittel - Bestimmung der Bruchwiderstandstemperatur
mittels eines gekerbten Drei-Punkt- Biegeversuches
Bitumes et liants bitumineux - Détermination de la température de résistance à la rupture
par un essai de flexion 3 points sur un barreau entaillé
Ta slovenski standard je istoveten z: CEN/TS 15963:2010
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
SIST-TS CEN/TS 15963:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 15963:2010
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 15963:2010
TECHNICAL SPECIFICATION
CEN/TS 15963
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
January 2010
ICS 91.100.50
English Version
Bitumen and bituminous binders - Determination of the fracture
toughness temperature by a three point bending test on a
notched specimen
Bitumes et liants bitumineux - Détermination de la Bitumen und bitumenhaltige Bindemittel - Bestimmung der
température de résistance à la fissuration par un essai de Bruchwiderstandstemperatur mittels eines Drei-Punkt-
flexion 3 points sur un barreau entaillé Biegeversuches an einem gekerbten Probekörper
This Technical Specification (CEN/TS) was approved by CEN on 26 October 2009 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15963:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 15963:2010
CEN/TS 15963:2010 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Principle .6
5 Apparatus .6
6 Preparation of test samples .9
7 Procedure to determine the Fracture Toughness temperature T . 12
FT
8 Calculation . 12
9 Expression of results . 13
10 Precision . 14
11 Test report .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.