EN 13075-2:2002
(Main)Bitumen and bituminous binders - Determination of breaking behaviour - Part 2: Determination of fines mixing time of cationic bitumen emulsions
Bitumen and bituminous binders - Determination of breaking behaviour - Part 2: Determination of fines mixing time of cationic bitumen emulsions
This European Standard specifies a method for the determination of the fines mixing time of cationic bitumen emulsions, under standardized conditions.
WARNING - The use of this standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Bitumen und bitumenhaltige Bindemittel - Bestimmung des Brechverhaltens - Teil 2: Bestimmung der Mischzeit von Feinanteilen in kationischen Bitumenemulsionen
Die Europäische Norm legt ein Verfahren zur Bestimmung der Mischzeit des Feingutes von kationischen Bitumenemulsionen unter normierten Bedingungen fest.
WARNUNG Die Anwendung dieser Norm kann den Umgang mit gefährlichen Substanzen und Ausrüstungen sowie die Durchführung gefährlicher Arbeitsschritte einschließen. Diese Norm erhebt nicht den Anspruch, dass alle mit ihrer Anwendung verbundenen Sicherheitsprobleme angesprochen werden. Es liegt in der Verantwortung des Anwenders dieser Norm, geeignete Vorsichtsmaßnahmen für den Arbeits- und Gesundheitsschutz zu treffen und die Anwendbarkeit einschränkender Vorschriften vor der Anwendung zu bestimmen.
Bitumes et liants bitumineux - Détermination du comportement à la rupture - Partie 2: Détermination de la durée de miscibilité des fines dans les émulsions cationiques de bitume
La présente norme européenne prescrit une méthode de détermination de la durée de miscibilité des fines dans les émulsions de bitume surstabilisées. NOTE : La méthode d'essai décrite peut être utilisée pour la détermination quantitative de la miscibilité des émulsions surstabilisées avec des fines minérales et dans des conditions normalisées. AVERTISSEMENT : L'utilisation de la présente norme européenne implique l'intervention de produits, d'opérations et d'équipements à caractère dangereux. La présente norme européenne n'a pas la prétention d'aborder tous les problèmes de sécurité concernés par son usage.
Bitumen in bitumenska veziva - Določevanje stopnje stabilnosti - 2. del: Določevanje hitrosti razpada kationskih bitumenskih emulzij
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2003
%LWXPHQLQELWXPHQVNDYH]LYD'RORþHYDQMHVWRSQMHVWDELOQRVWLGHO
'RORþHYDQMHKLWURVWLUD]SDGDNDWLRQVNLKELWXPHQVNLKHPXO]LM
Bitumen and bituminous binders - Determination of breaking behaviour - Part 2:
Determination of fines mixing time of cationic bitumen emulsions
Bitumen und bitumenhaltige Bindemittel - Bestimmung des Brechverhaltens - Teil 2:
Bestimmung der Mischzeit kationischer Bitumenemulsionen
Bitumes et liants bitumineux - Détermination du comportement a la rupture - Partie 2:
Détermination de la durée de miscibilité des fines dans les émulsions cationiques de
bitume
Ta slovenski standard je istoveten z: EN 13075-2:2002
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 13075-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2002
ICS 75.140; 91.100.50
English version
Bitumen and bituminous binders - Determination of breaking
behaviour - Part 2: Determination of fines mixing time of cationic
bitumen emulsions
Bitumes et liants bitumineux - Détermination du Bitumen und bitumenhaltige Bindemittel - Bestimmung des
comportement à la rupture - Partie 2: Détermination de la Brechverhaltens - Teil 2: Bestimmung der Mischzeit
durée de miscibilité des fines dans les émulsions kationischer Bitumenemulsionen
cationiques de bitume
This European Standard was approved by CEN on 14 March 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13075-2:2002 E
worldwide for CEN national Members.
Foreword
This document EN 13075-2:2002 has been prepared by Technical Committee CEN/TC 336 "Bituminous binders",
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by January 2003, and conflicting national standards shall be withdrawn at the latest
by January 2003.
This European Standard is part of a package including 14 standards: EN 1428, EN 1429, EN 1430, EN 1431,
EN 12846, EN 12847, EN 12848, EN 12849, EN 12850, EN 13074, EN 13075-1, EN 13075-2, EN 13614 and
EN 13808.
Annex A is normative.
This European Standard EN 13075 consists of the following parts under the general title Bitumen and bituminous
binders – Determination of breaking behaviour:
Part 1 – Determination of breaking value of cationic bitumen emulsions, mineral filler method;
Part 2 – Determination of fines mixing time of cationic bitumen emulsions.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,
Sweden, Switzerland and the United Kingdom.
1 Scope
This European Standard specifies a method for the determination of the fines mixing time of cationic bitumen
emulsions, under standardized conditions.
WARNING – The use of this standard may involve hazardous materials, operations and equipment. This
standard does not purport to address all of the safety problems associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety and health practices and
determine the applicability of regulatory limitations prior to use.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
1)
EN 58 , Bitumen and bituminous binders - Sampling bituminous binders.
EN ISO 3696, Water for analytical laboratory use - Specification and test methods (ISO 3696:1987).
EN 12594, Bitumen and bituminous binders – Preparation of test samples.
3 Term and definitio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.