Lasers and laser-related equipment - Test methods for determination of the shape of a laser beam wavefront - Part 1: Terminology and fundamental aspects (ISO 15367-1:2003)

ISO 15367-1:2003 specifies methods for the measurement of the topography of the wavefront of a laser beam by measurement and interpretation of the spatial distribution of the phase of that wavefront across a plane approximately perpendicular to its direction of propagation. Requirements are given for the measurement and analysis of phase distribution data to provide quantitative wavefront parameters and their uncertainty in a test report.
The methods described in ISO 15367-1:2003 are applicable to the testing and characterization of a wide range of beam types from both continuous wave and pulsed lasers. Definitions of parameters describing wavefront deformations are given together with methods for the determination of those parameters from phase distribution measurements.

Laser und Laseranlagen - Prüfverfahren für die Bestimmung der Wellenfrontform von Laserstrahlen - Teil 1: Begriffe und grundlegende Aspekte (ISO 15367-1:2003)

Die vorliegende Internationale Norm legt Messverfahren für die Topografie der Wellenfront eines Laserstrahls durch Messung und Auswertung der räumlichen Verteilung der Phasen dieser Wellenfront in einer Ebene rechtwinklig zu ihrer Ausbreitungsrichtung fest. Es werden Anforderungen für die Messung und Analyse von Phasenverteilungen aufgestellt, die die quantitative Angabe von Wellenfrontparametern und deren Messunsicherheit in einem Prüfbericht ermöglichen.
Die in dieser Internationalen Norm beschriebenen Verfahren gelten für die Prüfung und Beschreibung vieler Strahlenarten von Dauerstrichlasern sowie Pulslasern. Es werden Parameterdefinitionen für die Verformung von Wellenfronten sowie Verfahren zur Ermittlung dieser Parameter aus Messungen der Phasenverteilung angegeben.

Lasers et équipements associés aux lasers - Méthodes d'essai pour la détermination de la forme du front d'onde du faisceau laser - Partie 1: Terminologie et aspects fondamentaux (ISO 15367-1:2003)

L'ISO 15367-1:2003 spécifie les méthodes pour le mesurage de la topographie du front d'onde d'un faisceau laser par le mesurage et l'interprétation de la distribution spatiale de la phase de ce front d'onde, à travers un plan approximativement perpendiculaire à sa direction de propagation. Les exigences sont données pour le mesurage et l'analyse des données de la distribution de phase pour inscrire les paramètres quantitatifs du front d'onde et leurs incertitudes dans un rapport d'essai.
Les méthodes décrites dans l'ISO 15367-1:2003 sont applicables à l'essai et à la caractérisation d'une grande variété de types de faisceaux issus à la fois de lasers continus ou pulsés. Les définitions des paramètres décrivant les déformations du front d'onde sont données avec les méthodes pour la détermination de ces paramètres à partir des mesures de distribution de phase.

Laserji in laserska oprema – Preskusne metode za ugotavljanje oblike valovne fronte laserskega žarka – 1. del: Izrazje in temeljni vidiki (ISO 15367-1:2003)

General Information

Status
Published
Publication Date
14-Sep-2003
Withdrawal Date
30-Mar-2004
Current Stage
9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
Start Date
17-Dec-2008
Completion Date
17-Dec-2008

Buy Standard

Standard
EN ISO 15367-1:2003
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15367-1:2003
01-december-2003
Laserji in laserska oprema – Preskusne metode za ugotavljanje oblike valovne
fronte laserskega žarka – 1. del: Izrazje in temeljni vidiki (ISO 15367-1:2003)
Lasers and laser-related equipment - Test methods for determination of the shape of a
laser beam wavefront - Part 1: Terminology and fundamental aspects (ISO 15367-
1:2003)
Laser und Laseranlagen - Prüfverfahren für die Bestimmung der Wellenfrontform von
Laserstrahlen - Teil 1: Begriffe und grundlegende Aspekte (ISO 15367-1:2003)
Lasers et équipements associés aux lasers - Méthodes d'essai pour la détermination de
la forme du front d'onde du faisceau laser - Partie 1: Terminologie et aspects
fondamentaux (ISO 15367-1:2003)
Ta slovenski standard je istoveten z: EN ISO 15367-1:2003
ICS:
01.040.31 Elektronika (Slovarji) Electronics (Vocabularies)
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
SIST EN ISO 15367-1:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15367-1:2003

---------------------- Page: 2 ----------------------

SIST EN ISO 15367-1:2003
EUROPEAN STANDARD
EN ISO 15367-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2003
ICS 01.040.31; 31.260
English version
Lasers and laser-related equipment - Test methods for
determination of the shape of a laser beam wavefront - Part 1:
Terminology and fundamental aspects (ISO 15367-1:2003)
Lasers et équipements associés aux lasers - Méthodes Laser und Laseranlagen - Prüfverfahren für die
d'essai pour la détermination de la forme du front d'onde du Bestimmung der Wellenfrontform von Laserstrahlen - Teil
faisceau laser - Partie 1: Terminologie et aspects 1: Begriffe und grundlegende Aspekte (ISO 15367-1:2003)
fondamentaux (ISO 15367-1:2003)
This European Standard was approved by CEN on 1 September 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15367-1:2003 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15367-1:2003
EN ISO 15367-1:2003 (E)
Foreword
This document (EN ISO 15367-1:2003) has been prepared by Technical Committee ISO/TC 172
"Optics and optical instruments" in collaboration with Technical Committee CEN/TC 123 "Lasers
and laser-related equipment", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2004, and conflicting national
standards shall be withdrawn at the latest by March 2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
NOTE FROM CMC  The foreword is susceptible to be amended on reception of the German
language version. The confirmed or amended foreword, and when appropriate, the normative
annex ZA for the references to international publications with their relevant European
publications will be circulated with the German version.
Endorsement notice
The text of ISO 15367-1:2003 has been approved by CEN as EN ISO 15367-1:2003 without any
modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 15367-1:2003


INTERNATIONAL ISO
STANDARD 15367-1
First edition
2003-09-15


Lasers and laser-related equipment —
Test methods for determination of the
shape of a laser beam wavefront —
Part 1:
Terminology and fundamental aspects
Lasers et équipements associés aux lasers — Méthodes d'essai
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.