EN ISO 28199-1:2009
(Main)Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 1: Relevant vocabulary and preparation of test panels (ISO 28199-1:2009)
Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 1: Relevant vocabulary and preparation of test panels (ISO 28199-1:2009)
ISO 28199-1:2009 defines terms relating to the evaluation of coating materials in research, development and production with regard to their suitability and safety for industrial processes and error analysis.
ISO 28199-1:2009 specifies methods for the preparation of test panels and the subsequent measurement of film thickness, colour and surface texture.
Beschichtungsstoffe - Beurteilung applikationsbedingter Eigenschaften von Beschichtungssystemen - Teil 1: Begriffe und Vorbereitung der Probenplatten (ISO 28199-1:2009)
Dieser Teil von ISO 28199 legt Begriffe hinsichtlich der Beurteilung von Beschichtungsstoffen in Forschung, Entwicklung und Produktion bezüglich ihrer Prozesseignung, Prozesssicherheit und Fehleranalyse fest.
Dieser Teil von ISO 28199 legt Verfahren zum Herstellen der Probenplatten und anschließendem Messen von Schichtdicke, Farbe und Oberflächenstruktur fest.
Peintures et vernis - Évaluation des propriétés des systèmes de revêtement liées au mode d'application - Partie 1: Vocabulaire pertinent et préparation des panneaux d'essai (ISO 28199-1:2009)
L'ISO 28199‑1:2009 définit des termes liés à l'évaluation des matériaux de revêtement, aux niveaux recherche, développement et production, en ce qui concerne leur adaptation aux procédés industriels et leur sécurité ainsi que l'analyse des erreurs.
L'ISO 28199‑1:2009 spécifie des méthodes de préparation des panneaux d'essai et de mesurage ultérieur de l'épaisseur du feuil, de sa couleur et de sa texture superficielle.
Barve in laki - Vrednotenje lastnosti premaznih sistemov pri nanašanju - 1. del: Slovar in priprava preskusnih plošč (ISO 28199-1:2009)
Ta del ISO 28199 določa pogoje glede vrednotenja premaznih materialov pri raziskavah, razvoju in proizvodnji z ozirom na njihovo primernost in varnost za industrijske postopke ter analizo napak. Ta del ISO 28199 opredeljuje metode priprave preskusnih plošč ter naknadnega merjenja debeline prevleke, barve in strukture površine.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Beschichtungsstoffe - Beurteilung applikationsbedingter Eigenschaften von Beschichtungssystemen - Teil 1: Begriffe und Vorbereitung der Probenplatten (ISO 28199-1:2009)Peintures et vernis - Évaluation des propriétés des systèmes de revêtement liées au mode d'application - Partie 1: Vocabulaire pertinent et préparation des panneaux d'essai (ISO 28199-1:2009)Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 1: Relevant vocabulary and preparation of test panels (ISO 28199-1:2009)87.040Barve in lakiPaints and varnishesICS:Ta slovenski standard je istoveten z:EN ISO 28199-1:2009SIST EN ISO 28199-1:2010en,fr,de01-januar-2010SIST EN ISO 28199-1:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 28199-1
September 2009 ICS 87.040 English Version
Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 1: Relevant vocabulary and preparation of test panels (ISO 28199-1:2009)
Peintures et vernis - Évaluation des propriétés des systèmes de revêtement liées au mode d'application - Partie 1: Vocabulaire pertinent et préparation des panneaux d'essai (ISO 28199-1:2009)
Beschichtungsstoffe - Beurteilung applikationsbedingter Eigenschaften von Beschichtungssystemen - Teil 1: Begriffe und Vorbereitung der Probenplatten (ISO 28199-1:2009) This European Standard was approved by CEN on 21 May 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 28199-1:2009: ESIST EN ISO 28199-1:2010
Reference numberISO 28199-1:2009(E)© ISO 2009
INTERNATIONAL STANDARD ISO28199-1First edition2009-09-01Paints and varnishes — Evaluation of properties of coating systems related to the application process — Part 1: Relevant vocabulary and preparation of test panels Peintures et vernis — Évaluation des propriétés des systèmes de revêtement liées au mode d'application — Partie 1: Vocabulaire pertinent et préparation des panneaux d'essai
ISO 28199-1:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2009 – All rights reserved
ISO 28199-1:2009(E) © ISO 2009 – All rights reserved iii Contents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 Principle.5 5 Apparatus.5 6 Calibration.6 7 Sampling.6 8 Test panels.6 8.1 Substrate.6 8.2 Preparation of the test panel.6 8.3 Coating of the test panel.8 8.3.1 General.8 8.3.2 Version A (perforated panel).9 8.3.3 Version B (non-perforated panel).9 8.4 Film thickness.11 9 Procedure.11 9.1 Conditioning the test panels.11 9.2 Test conditions.11 9.3 Number of determinations.11 9.4 Test.12 9.4.1 Measurement pattern.12 9.4.2 Film thickness.13 9.4.3 Colour.13 9.4.4 Surface texture.14 10 Evaluation.14 11 Precision.14 12 Test report.14 Annex A (informative)
Examples of appropriate application parameters.15 Bibliography.19
ISO 28199-1:2009(E) iv © ISO 2009 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. ISO 28199-1 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 9, General test methods for paints and varnishes. ISO 28199 consists of the following parts, under the general title Paints and varnishes — Evaluation of properties of coating systems related to the application process: ⎯ Part 1: Relevant vocabulary and preparation of test panels ⎯ Part 2: Colour stability, process hiding power, re-dissolving, overspray absorption, wetting, surface texture and mottling ⎯ Part 3: Visual assessment of sagging, formation of bubbles, pinholing and hiding power SIST EN ISO 28199-1:2010
ISO 28199-1:2009(E) © ISO 2009 – All rights reserved v Introduction In many areas (e.g. car manufacture, industrial coatings, coatings for plastics) the coating materials used are adapted to the specific application equipment and technologies of the particular user. A coating material is, therefore, to be understood as a semi-manufactured product that only receives its final form in combination with the specific application conditions. The adaptation to the application conditions is therefore decisive for the quality of the coated product. The test methods specified in ISO 28199 are based on studies by a Working Group of the European Council for Automotive R&D (EUCAR). They may be used for evaluation of coating materials in research, development and production with regard to their suitability and safety for industrial processes, and error analysis. The properties of coating materials and coatings to be evaluated depend on the film thickness, so a coating system of increasing thickness is applied to a test panel under defined conditions. The following characteristics are measured (in this part of ISO 28199): ⎯ film thickness in accordance with ISO 2808; ⎯ surface texture; ⎯ colour in accordance with ISO 7724 (all parts). In combination with visual assessment, the following properties are determined: ⎯ colour stability, process hiding power, re-dissolving, overspray absorption, wetting, surface texture and mottling (ISO 28199-2); ⎯ tendency toward sagging, formation of bubbles, pinholing and hiding power (ISO 28199-3). The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that compliance with this document may involve the use of a patent concerning the locally related measurements used in Version A in Clauses 8 and 9. ISO takes no position concerning the evidence, validity and scope of this patent right. The holder of this patent right has assured ISO that he is willing t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.