FprCEN ISO/TS 19392-6
(Main)Paints and varnishes - Coating systems for wind-turbine rotor blades - Part 6: Determination and evaluation of ice adhesion using centrifuge (ISO/DTS 19392-6:2025)
Paints and varnishes - Coating systems for wind-turbine rotor blades - Part 6: Determination and evaluation of ice adhesion using centrifuge (ISO/DTS 19392-6:2025)
This document describes a method to measure ice adhesion from artificial ice on test substrates by using a centrifuge. Basic ice types are defined and test parameters for the ice removal are described to achieve reproducibility of test results for ice adhesion measurements for rotor blade coatings. This document does not intend to provide fixed test parameter to account for the diversity of relevant icing scenarios in this field of application.
Beschichtungsstoffe - Beschichtungssysteme für Rotorblätter von Windenergieanlagen - Teil 6: Bestimmung und Bewertung der Eisadhäsion mittels Zentrifuge (ISO/DTS 19392-6:2025)
Dieses Dokument legt ein Verfahren zum Messen der Eisadhäsion von technisch hergestelltem Eis auf Probensubstraten unter Verwendung einer Zentrifuge fest. Grundlegende Eistypen werden festgelegt und Prüfparameter für die Eisentfernung beschrieben, um die Vergleichbarkeit der Prüfergebnisse für die Eishaftmessung von Rotorblattbeschichtungen zu erreichen. Dieses Dokument beabsichtigt nicht, feste Prüfparameter vorzugeben, um der Vielfalt der relevanten Vereisungsszenarien in diesem Anwendungsbereich Rechnung zu tragen.
ANMERKUNG In der Praxis kann die Eishaftung durch zwei verschiedene Messprinzipien bestimmt werden, den Zentrifugaltest (in diesem Dokument behandelt) und den Schertest, die sich in den dynamischen und quasistatischen Schergeschwindigkeiten unterscheiden.
Mit diesem Prüfverfahren kann die Adhäsion von dynamischem Eis auf dem Beschichtungssystem eines Rotorblattes einer Windkraftanlage im Betrieb geprüft werden.
Peintures et vernis - Matériaux de revêtement pour pales de turbines éoliennes - Partie 6: Détermination et évaluation de l'adhésion de la glace à l'aide d'une centrifugeuse (ISO/DTS 19392-6:2025)
Barve in laki - Premazni sistemi za lopatice rotorjev vetrnih turbin - 6. del: Ugotavljanje in vrednotenje oprijema ledu z uporabo centrifuge (ISO/DTS 19392-6:2025)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2025
Barve in laki - Premazni sistemi za lopatice rotorjev vetrnih turbin - 6. del:
Ugotavljanje in vrednotenje oprijema ledu z uporabo centrifuge (ISO/DTS 19392-
6:2025)
Paints and varnishes - Coating systems for wind-turbine rotor blades - Part 6:
Determination and evaluation of ice adhesion using centrifuge (ISO/DTS 19392-6:2025)
Beschichtungsstoffe - Beschichtungssysteme für Rotorblätter von Windenergieanlagen -
Teil 6: Bestimmung und Bewertung der Eisadhäsion mittels Zentrifuge (ISO/DTS 19392-
6:2025)
Peintures et vernis - Matériaux de revêtement pour pales de turbines éoliennes - Partie
6: Détermination et évaluation de l'adhésion de la glace à l'aide d'une centrifugeuse
(ISO/DTS 19392-6:2025)
Ta slovenski standard je istoveten z: FprCEN ISO/TS 19392-6
ICS:
27.180 Vetrne elektrarne Wind turbine energy systems
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
FINAL DRAFT
Technical
Specification
ISO/DTS 19392-6
ISO/TC 35/SC 9
Paints and varnishes — Coating
Secretariat: BSI
systems for wind-turbine rotor
Voting begins on:
blades —
2025-06-02
Part 6:
Voting terminates on:
2025-08-25
Determination and evaluation of ice
adhesion using centrifuge
Peintures et vernis — Matériaux de revêtement pour pales de
turbines éoliennes —
Partie 6: Détermination et évaluation de l'adhésion de la glace à
l'aide d'une centrifugeuse
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/DTS 19392-6:2025(en) © ISO 2025
FINAL DRAFT
ISO/DTS 19392-6:2025(en)
Technical
Specification
ISO/DTS 19392-6
ISO/TC 35/SC 9
Paints and varnishes — Coating
Secretariat: BSI
systems for wind-turbine rotor
Voting begins on:
blades —
Part 6:
Voting terminates on:
Determination and evaluation of ice
adhesion using centrifuge
Peintures et vernis — Matériaux de revêtement pour pales de
turbines éoliennes —
Partie 6: Détermination et évaluation de l'adhésion de la glace à
l'aide d'une centrifugeuse
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2025
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DTS 19392-6:2025(en) © ISO 2025
ii
ISO/DTS 19392-6:2025(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Sampling . 2
7 Test panels . 2
7.1 Substrate .2
7.2 Preparation .3
7.3 Conditioning.3
7.4 Coating thickness .3
7.5 Roughness of coating .3
8 Procedure . 3
8.1 Number of determinations .3
8.2 Examination before exposure . .4
8.3 Sample preparation (ice formation) .4
8.4 Ice adhesion testing .4
8.5 Examination after testing .5
9 Evaluation . 5
10 Precision . 5
11 Test report . 6
Annex A (informative) Example of parameters for ice formation processes . 7
Bibliography . 8
iii
ISO/DTS 19392-6:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO/TS 19392-6:2023), which has been technically
revised.
The main changes are as follows:
— in Clause 1 a note has been added to give more information on the different methods for the determination
of ice adhesion;
— in 8.3, in the seventh paragraph, considerations on the presence of mould were added;
— in 8.4, Table 1, a header and a separate column for the units were inserted;
— in Clause 9, Formula (1), ω was corrected to the angular momentum ω and the explanation of symbols
was updated;
— in Annex A an introductory sentence was added;
— in Table A.1 a separate column for the units was inserted.
A list of all parts in the ISO 19392 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO/DTS 19392-6:2025(en)
Introduction
Ice accretion on rotor blade surfaces of wind turbines can decrease the efficiency and limit the performance
of wind turbines in cold, humid environments. Ice formation can also lead to damage of the rotor blade and
can be hazardous, if ice falls off the blade. Icephobic coatings (“icephobics”) can be applied to rotor blade
surfaces to reduce or prevent the adhesion of ice by removing ice prior to reaching a critical ice mass for the
rotor blades. They can also increase the efficiency of thermal ice protection systems.
v
FINAL DRAFT Technical Specification ISO/DTS 19392-6:2025(en)
Paints and varnishes — Coating systems for wind-turbine
rotor blades —
Part 6:
Determination and evaluation of ice adhesion using
centrifuge
1 Scope
This document specifies a method to measure ice adhesion from artificial ice on test substrates by using
a centrifuge. Basic ice types are defined and test parameters for the ice removal are described to achieve
reproducibility of test results for ice adhesion measurements for rotor blade coatings. This document does
not intend to provide fixed test parameter to account for the diversity of relevant icing scenarios in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.