EN ISO 11197:2019
(Main)Medical supply units (ISO 11197:2019)
Medical supply units (ISO 11197:2019)
IEC 60601-1:2005+A1:2012, 1.1 is replaced by:
This document applies to the basic safety and essential performance of medical supply units, hereafter also referred to as ME equipment.
This document applies to medical supply units manufactured within a factory or assembled on site, including cabinetry and other enclosures, which incorporate patient care services.
NOTE 1 A party that assembles on site various components intended for patient care services into an enclosure is considered the manufacturer of the medical supply unit.
Hazards inherent in the intended function of ME equipment or ME systems within the scope of this document are not covered by specific requirements in this standard, except in of IEC 60601-1:2005+A1:2012, 7.2.13 and 8.4.1 (see 201.1.4).
NOTE 2 Refer to IEC 60601-1:2005+A1:2012, 4.2.
Medizinische Versorgungseinheiten (ISO 11197:2019)
Diese Besonderen Festlegungen beziehen sich auf solche anwendbaren Ergänzungsnormen, die in IEC 60601-1:2005 + A1:2015, Abschnitt 2 und in Abschnitt 201.2 dieser Besonderen Festlegungen aufgeführt sind.
IEC 60601-1-3:2008 + A1:2013, IEC 60601-1-8:2006 + A1:2012, IEC 60601-1-9:2007, IEC 60601 1 10:2007 + A1:2013 und IEC 60601-1-11 sowie IEC 60601-1-12 gelten nicht.
ANMERKUNG Ergänzungsnormen werden durch ihre Dokumentennummer referenziert.
Gaines techniques à usage médical (ISO 11197:2019)
Le paragraphe 1.1 de l'IEC 60601-1:2005+A1:2012 est remplacé par:
Le présent document s'applique à la sécurité de base et aux performances essentielles des gaines techniques à usage médical, également désignées sous le terme d'appareil EM.
Le présent document s'applique aux gaines techniques à usage médical fabriquées en usine ou montées sur site, y compris les armoires et autres enveloppes, qui intègrent des services de soins aux patients.
NOTE 1 Une entité qui monte sur site divers composants destinés à des services de soins aux patients pour constituer une enveloppe est considérée comme le fabricant de la gaine technique à usage médical.
Les dangers inhérents à la fonction prévue de l'appareil EM ou des systèmes EM dans le cadre du domaine d'application du présent document ne sont pas couverts par des exigences spécifiques contenues dans la présente norme, à l'exception des paragraphes 7.2.13 et 8.4.1 de l'IEC 60601‑1:2005+A1:2012, (voir 201.1.4).
NOTE 2 Voir le paragraphe 4.2 de l'IEC 60601-1:2005+A1:2012.
Enote za oskrbo v medicini (ISO 11197:2019)
Ta standard se uporablja za osnovno varnost in bistvene lastnosti enot za oskrbo v medicini (v nadaljevanju »medicinska električna oprema«). Ta dokument se uporablja za enote za oskrbo v medicini, proizvedene v tovarni ali sestavljene na mestu uporabe, vključno z omaricami in drugimi ohišji, ki zajemajo storitve oskrbe pacientov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2020
Nadomešča:
SIST EN ISO 11197:2016
Enote za oskrbo v medicini (ISO 11197:2019)
Medical supply units (ISO 11197:2019)
Medizinische Versorgungseinheiten (ISO 11197:2019)
Gaines techniques à usage médical (ISO 11197:2019)
Ta slovenski standard je istoveten z: EN ISO 11197:2019
ICS:
11.040.01 Medicinska oprema na Medical equipment in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11197
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2019
EUROPÄISCHE NORM
ICS 11.040.10 Supersedes EN ISO 11197:2016
English Version
Medical supply units (ISO 11197:2019)
Gaines techniques à usage médical (ISO 11197:2019) Medizinische Versorgungseinheiten (ISO 11197:2019)
This European Standard was approved by CEN on 15 September 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11197:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11197:2019) has been prepared by Technical Committee ISO/TC 121
"Anaesthetic and respiratory equipment" in collaboration with Technical Committee CEN/TC 215
“Respiratory and anaesthetic equipment” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2020, and conflicting national standards shall be
withdrawn at the latest by May 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11197:2016.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11197:2019 has been approved by CEN as EN ISO 11197:2019 without any modification.
INTERNATIONAL ISO
STANDARD 11197
Fourth edition
2019-11
Medical supply units
Gaines techniques à usage médical
Reference number
ISO 11197:2019(E)
©
ISO 2019
ISO 11197:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO 11197:2019(E)
Contents Page
Foreword . iv
Introduction . v
201.1 Scope, object and related standards . 1
201.1.1 Scope . 1
201.1.2 Object . 1
201.1.3 Related standards . 1
201.1.3.1 General and Collateral standards . 1
201.1.3.2 Particular standards . 2
201.2 Normative references . 2
201.3 Terms and definitions . 3
201.4 General requirements . 5
201.5 General requirements for testing ME equipment . 5
201.6 Classification of ME equipment and ME systems . 5
201.7 ME equipment identification, marking and documents . 6
201.8 Protection against electrical hazards from ME equipment . 10
201.9 Protection against mechanical hazards of ME equipment and ME systems . 17
201.10 Protection against unwanted and excessive radiation hazards . 20
201.11 Protection against excessive temperatures and other hazards . 20
201.12 Accuracy of controls and instruments and protection against hazardous outputs . 21
201.13 Hazardous situations and fault conditions . 21
201.13.2.2 Single fault conditions . 21
201.14 Programmable electrical medical systems (PEMS) . 22
201.15 Construction of ME equipment . 22
201.16 ME systems . 27
201.17 Electromagnetic compatibility of ME equipment and ME systems . 27
202 Medical electrical equipment — Parts 1-2 General requirements for basic safety and
essential performance — Collateral standard: Electromagnetic disturbances — Requirements
and tests . 27
206 Medical electrical equipment — Parts 1-6 General requirements for basic safety and
essential performance — Collateral standard: Usability. 27
Annex A A (informative) Rationale . 28
Annex B B (informative) Tests during production . 29
Annex C C (informative) Documentation . 33
Annex D D (informative) Terminology — Alphabetical index of defined terms . 34
Bibliography . 36
iii
ISO 11197:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 121, Anaesthetic and respiratory
equipment, Subcommittee SC 6, Medical gas supply systems.
This fourth edition cancels and replaces the third edition (ISO 11197:2016), which has been technically
revised. The main changes compared to the previous edition are as follows:
— editorial revision;
— change in the requirements defining the inclusion of USB outlets within medical supply units;
— addition of methods of internal cabling connections and specific tests including but not limited to
impact resistance.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO 11197:2019(E)
Introduction
Many healthcare facilities use surface-mounted or recessed containment systems and enclosures for
accommodating and displaying essential patient care services. These are known as medical supply units.
This document specifies requirements for medical supply units manufactured in factories or assembled
from components on site.
It is intended for use by those persons involved in the design, construction, inspection, testing,
maintenance and operation of healthcare facilities as well as those manufacturing, assembling and
installing medical supply units.
Persons involved in the design, manufacture, installation, maintenance and testing of equipment
intended to be connected to gas for medicinal use, medical device gas, vacuum, anaesthetic gas scavenging
and/or plume extraction systems should be aware of the contents of this document.
This document is a particular standard, based on IEC 60601-1:2005+A1:2012. IEC 60601-
1:2005+A1:2012 is the basic standard for the safety of all medical electrical equipment used by or under
the supervision of qualified personnel in the general medical and patient environment; it also contains
certain requirements for reliable operation to ensure safety.
IEC 60601-1:2005+A1:2012 has associated collateral standards and particular standards. The collateral
standards include requirements for specific technologies and/or hazards and apply to all applicable
equipment, such as medical systems, electromagnetic compatibility (EMC), radiation protection in
di
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.