EN 6081:2016
(Main)Aerospace series - Rivet, universal head, close tolerance - Inch series
Aerospace series - Rivet, universal head, close tolerance - Inch series
This European Standard specifies the dimensions, tolerances and mass of rivets with universal head, close tolerance, inch series, for aerospace application.
Luft- und Raumfahrt - Vollniet, Universalkopf, enge Toleranz - Zoll-Reihe
Série aérospatiale - Rivets de précision, tête universelle - Série en inches
Aeronavtika - Kovice, univerzalna glava, ozka toleranca - Colska izvedba
Ta standard določa dimenzije, tolerance in maso kovic z univerzalno glavo, ozka toleranca, colska izvedba za uporabo v aeronavtiki.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 6081:2016
01-november-2016
Aeronavtika - Kovice, univerzalna glava, ozka toleranca - Colska izvedba
Aerospace series - Rivet, universal head, close tolerance - Inch series
Luft- und Raumfahrt - Vollniet, Universalkopf, enge Toleranz - Zoll-Reihe
Série aérospatiale - Rivets de précision, tête universelle - Série en inches
Ta slovenski standard je istoveten z: EN 6081:2016
ICS:
49.030.60 Kovice Rivets
SIST EN 6081:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 6081:2016
---------------------- Page: 2 ----------------------
SIST EN 6081:2016
EN 6081
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2016
EUROPÄISCHE NORM
ICS 49.030.60
English Version
Aerospace series - Rivet, universal head, close tolerance -
Inch series
Série aérospatiale - Rivets de précision, tête universelle Luft- und Raumfahrt - Vollniet, Universalkopf, enge
- Série en inches Toleranz - Zoll-Reihe
This European Standard was approved by CEN on 2 January 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6081:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 6081:2016
EN 6081:2016 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Requirements . 5
3.1 Configuration, dimensions, tolerances and mass . 5
3.2 Material and surface treatment. 5
4 Designation . 7
5 Marking . 8
5.1 Material identification . 8
5.2 Manufacturers identification . 8
6 Technical specification . 8
6.1 Titanium alloy rivet . 8
6.2 Aluminium alloy rivet . 8
2
---------------------- Page: 4 ----------------------
SIST EN 6081:2016
EN 6081:2016 (E)
European foreword
This doc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.