EN 4359:2006

Aerospace series - Six lobe recess - Drivers - Technical specification

This standard specifies the characteristics, qualification and acceptance requirements for drivers for installing and removing screws and bolts having six lobe recess internal drive.

Luft- und Raumfahrt - Sechs-Bogenzahn-Innenantrieb - Schraubendrehereinsätze - Technische Lieferbedingungen

Diese Norm legt die Eigenschaften und die Anforderungen an die Qualifikation und Abnahme von Schrauben¬drehern mit einem Sechs-Bogenzahn-Innenantrieb zum Einsetzen und Entfernen von Schrauben fest.

Série aérospatiale - Empreinte six lobes - Embouts de tournevis - Spécification technique

Aeronavtika - Šestzoba vdolbina, notranji pogon - Nastavki za izvijače - Tehnična specifikacija

General Information

• Status: Published
• Publication Date: 19-Dec-2006
• Withdrawal Date: 29-Jun-2007
• ICS: 49.030.99 - Other fasteners
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 31-May-2017
• Ref Project: SIST EN 4359:2009 - Aerospace series - Six lobe recess - Drivers - Technical specification

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.VSHFLILNDFLMDLuft- und Raumfahrt - Sechs-Bogenzahn-Innenantrieb - Schraubendrehereinsätze - Technische LieferbedingungenSérie aérospatiale - Empreinte six lobes - Embouts de tournevis - Spécification techniqueAerospace series - Six lobe recess - Drivers - Technical specification49.030.99Drugi vezni elementiOther fastenersICS:Ta slovenski standard je istoveten z:EN 4359:2006SIST EN 4359:2009en,de01-maj-2009SIST EN 4359:2009SLOVENSKI
STANDARD



SIST EN 4359:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 4359December 2006ICS 49.030.99 English VersionAerospace series - Six lobe recess - Drivers - TechnicalspecificationSérie aérospatiale - Empreinte six lobes - Embouts detournevis - Spécification techniqueLuft- und Raumfahrt - Sechs-Bogenzahn, Innenantrieb -Schraubendrehereinsätze - Technische LieferbedingungenThis European Standard was approved by CEN on 28 August 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4359:2006: ESIST EN 4359:2009



EN 4359:2006 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Required characteristics.4 5 Performance.5 6 Quality assurance.6 7 Qualification and acceptance procedures.6 8 Test methods.6 9 Marking/packing.7
SIST EN 4359:2009



EN 4359:2006 (E) 3 Foreword This document (EN 4359:2006) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Irelan
...