EN ISO 16859-1:2015
(Main)Metallic materials - Leeb hardness test - Part 1: Test method (ISO 16859-1:2015)
Metallic materials - Leeb hardness test - Part 1: Test method (ISO 16859-1:2015)
ISO 16859-1:2015 covers the determination of a dynamic hardness of metallic materials using seven different Leeb scales (HLD, HLS, HLE, HLDL, HLD+15, HLC, HLG).
Metallische Werkstoffe - Härteprüfung nach Leeb - Teil 1: Prüfverfahren (ISO 16859-1:2015)
Diese Norm legt die Bestimmung der Leeb-Härte von metallischen Werkstoffen unter Verwendung von sechs verschiedenen Leeb-Skalen (HLD, HLS, HLE, HLDL, HLD15, HLC, HLG) fest.
Matériaux métalliques - Essai de dureté Leeb - Partie 1 : Méthode d'essai (ISO 16859-1:2015)
L'ISO 16859-1:2015 couvre la détermination de la dureté Leeb des matériaux métalliques au moyen de sept échelles Leeb différentes (HLD, HLS, HLE, HLDL, HLD+15, HLC, HLG).
Kovinski materiali - Preskus trdote po Leebu - 1. del: Preskusna metoda (ISO 16859-1:2015)
Ta standard zajema ugotavljanje trdote kovinskih materialov po Leebu s šestimi različnimi lestvicami po Leebu (HLD, HLS, HLE, HLDL, HLC, HLG).
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 16859-1:2016
01-januar-2016
Kovinski materiali - Preskus trdote po Leebu - 1. del: Preskusna metoda (ISO
16859-1:2015)
Metallic materials - Leeb hardness test - Part 1: Test method (ISO 16859-1:2015)
Metallische Werkstoffe - Härteprüfung nach Leeb - Teil 1: Prüfverfahren (ISO 16859-
1:2015)
Matériaux métalliques - Essai de dureté Leeb - Partie 1: Méthode d'essai (ISO 16859-
1:2015)
Ta slovenski standard je istoveten z: EN ISO 16859-1:2015
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 16859-1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 16859-1:2016
---------------------- Page: 2 ----------------------
SIST EN ISO 16859-1:2016
EN ISO 16859-1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2015
EUROPÄISCHE NORM
ICS 77.040.10
English Version
Metallic materials - Leeb hardness test - Part 1: Test
method (ISO 16859-1:2015)
Matériaux métalliques - Essai de dureté Leeb - Partie 1 Metallische Werkstoffe - Härteprüfung nach Leeb - Teil
: Méthode d'essai (ISO 16859-1:2015) 1: Prüfverfahren (ISO 16859-1:2015)
This European Standard was approved by CEN on 10 July 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16859-1:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 16859-1:2016
EN ISO 16859-1:2015 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 16859-1:2016
EN ISO 16859-1:2015 (E)
European foreword
This document (EN ISO 16859-1:2015) has been prepared by Technical Committee ISO/TC 164
“Mechanical testing of metals” in collaboration with Technical Committee ECISS/TC 101 “Test methods
for steel (other than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2016, and conflicting national standards shall be
withdrawn at the latest by April 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16859-1:2015 has been approved by CEN as EN ISO 16859-1:2015 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 16859-1:2016
---------------------- Page: 6 ----------------------
SIST EN ISO 16859-1:2016
INTERNATIONAL ISO
STANDARD 16859-1
First edition
2015-09-15
Metallic materials — Leeb hardness
test —
Part 1:
Test method
Matériaux métalliques — Essai de dureté Leeb —
Partie 1: Méthode d’essai
Reference number
ISO 16859-1:2015(E)
©
ISO 2015
---------------------- Page:
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.