prEN 1338
(Main)Concrete paving blocks - Requirements and test methods
Concrete paving blocks - Requirements and test methods
This European Standard specifies materials, properties, requirements and test methods for unreinforced cement bound concrete paving blocks and complementary fittings. It is applicable to precast concrete paving blocks and complementary fittings for pedestrian use, vehicular use and roof coverings, e.g. footpaths, precincts, cycle tracks, car parks, roads, highways, industrial areas (including docks and harbours), aircraft pavements, bus stations, petrol filling stations.
This standard does not deal with the tactility or visibility of blocks
Blocks with side features to provide wider joints for permeable pavements are included.
Permable blocks with large holes or voids or with an interconnected pore structure to allow water to pass through the block to provide a porous pavement are not included.
In case of regular use of studded tyres additional requirements are sometimes needed.
This standard provides for the product marking and the evaluation of conformity of the product to this European Standard.
Pflastersteine aus Beton - Anforderungen und Prüfverfahren
Diese Europäische Norm beschreibt Materialien, Eigenschaften, Anforderungen und Prüfverfahren für unbewehrte Pflastersteine und Ergänzungssteine aus zementgebundenem Beton. Sie gilt für vorgefertigte Pflastersteine und Ergänzungssteine aus Beton im Fußgänger- und Verkehrsbereich und auf Dächern, z. B. Fußwege, Fußgängerzonen, Radwege, Parkplätze, Straßen, Autobahnen, Industriebereiche (einschließlich Docks und Häfen), Flugzeugrollbahnen, Busbahnhöfe und Tankstellen.
Diese Norm befasst sich nicht mit der Tastbarkeit und der visuellen Wahrnehmbarkeit von Pflastersteinen.
Es sind Pflastersteine für den Einsatz bei wasserdurchlässigen Pflastern einbezogen, die seitliche Verbund- oder Verlegemerkmale zur Bildung weiterer Fugen aufweisen.
Wasserdurchlässige Pflastersteine mit großen Hohlräumen oder einer vernetzten Porenstruktur zur Schaffung eines porösen Pflasters, das Wasserdurchlässigkeit ermöglicht, sind nicht einbezogen.
Bei regelmäßiger Verwendung von Spikereifen sind manchmal zusätzliche Anforderungen notwendig.
Diese Norm regelt die Produktkennzeichnung und die Beurteilung der Übereinstimmung des Produkts mit dieser Europäischen Norm.
Pavés en béton - Prescriptions et méthodes d'essai
La présente Norme européenne spécifie les matériaux, les propriétés, les prescriptions et les méthodes
d'essai relatifs aux pavés en béton à liant ciment non armé et à leurs pièces complémentaires. Elle s'applique
aux pavés préfabriqués en béton et à leurs pièces complémentaires à l'usage des piétons et des véhicules
ainsi que des toitures, par exemple pour chemins piétonniers, zones piétonnes, pistes cyclables, parkings,
routes, autoroutes, aires industrielles (y compris docks et ports), pavages d'aéroports, arrêts de bus, stations
services.
La présente norme ne traite pas de la perception visuelle ou tactile des pavés.
Les pavés avec des caractéristiques latérales qui assurent des joints plus larges pour des pavages
perméables sont inclus.
Les pavés perméables avec de larges trous ou vides, ou dotés d’une structure de pores interconnectés
permettant à l’eau de traverser le pavé pour fournir une chaussée poreuse, ne sont pas inclus.
En cas d'utilisation régulière de pneus cloutés, des prescriptions supplémentaires sont parfois nécessaires.
La présente norme définit le marquage du produit et l'évaluation de sa conformité à la présente Norme
européenne.
Betonski tlakovci - Zahteve in preskusne metode
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2010
Betonski tlakovci - Zahteve in preskusne metode
Concrete paving blocks - Requirements and test methods
Pflastersteine aus Beton - Anforderungen und Prüfverfahren
Pavés en béton - Prescriptions et méthodes d'essai
Ta slovenski standard je istoveten z: prEN 1338
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2010
ICS 93.080.20 Will supersede EN 1338:2003
English Version
Concrete paving blocks - Requirements and test methods
Pavés en béton - Prescriptions et méthodes d'essai Pflastersteine aus Beton - Anforderungen und
Prüfverfahren
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 178.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1338:2010: E
worldwide for CEN national Members.
Contents Page
Foreword . 3
1 Scope . 3
2 Normative references . 3
3 Terms and definitions . 4
4 Requirements for materials . 6
5 Requirements for products. 7
6 Evaluation of conformity criteria . 12
7 Marking. 17
8 Test report . 17
Annex A (informative) Inspection schemes . 19
Annex B (normative) Procedure for acceptance testing of a consignment at delivery . 23
Annex C (normative) Measurement of the dimensions of a single block . 25
Annex D (normative) Determination of freeze/thaw resistance with de-icing salt . 29
Annex E (normative) Determination of total water absorption. 35
Annex F (normative) Measurement of strength . 37
Annex G (normative) Measurement of abrasion resistance . 41
Annex H (normative) Measuring of abrasion according to the Böhme test . 48
Annex I (normative) Method for the determination of unpolished slip resistance value (USRV) . 52
Annex J (normative) Verification of visual aspects . 59
Annex K (informative) Example of the application of the method for checking conformity of
tensile splitting strength by variables (6.3.8.3.B) . 60
Annex ZA (informative) Clauses of this European Standard addressing the provisions of the
EU Construction Products Directive (89/106/EEC) . 63
Foreword
This document (prEN 1338:2010) has been prepared by Technical Committee CEN/TC 178 “Paving units
and kerbs”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 1338:2003.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
1 Scope
This European Standard specifies materials, properties, requirements and test methods for unreinforced
cement bound concrete paving blocks and complementary fittings. It is applicable to precast concrete paving
blocks and complementary fittings for pedestrian use, vehicular use and roof coverings, e.g. footpaths,
precincts, cycle tracks, car parks, roads, highways, industrial areas (including docks and harbours), aircraft
pavements, bus stations, petrol filling stations.
This standard does not deal with the tactility or visibility of blocks
Blocks with side features to provide wider joints for permeable pavements are included.
Permable blocks with large holes or voids or with an interconnected pore structure to allow water to pass
through the block to provide a porous pavement are not included.
In case of regular use of studded tyres additional requirements are sometimes needed.
This standard provides for the product marking and the evaluation of conformity of the product to this
European Standard.
2 Normative references
This European Standard incorporates by dated and undated references, provisions from other publications.
These normative references are cited at the appropriate places in the text, and the publications are listed
hereafter. For dated references subsequent amendments to or revisions of any of these publications apply to
this European Standard only when incorporated in it by amendment or revision. For undated references, the
latest edition of the publication referred to applies (including amendments).
EN 10083-2, Quenched and tempered steels — Part 2: Technical delivery conditions for unalloyed quality
steels.
EN 13369, Common rules for precast concrete products.
EN ISO 4288, Geometric product specification (GPS) - Surface texture: Profile method - Rules and
procedures for the assessment of surface texture (ISO 4288:1996).
EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:1999).
EN ISO 6506-2, Metallic materials - Brinell hardness test - Part 2: Verification and calibration of testing
machines (ISO 6506-2:1999).
EN ISO 6506-3, Metallic materials - Brinell hardness test - Part 3: Calibration of reference blocks
(ISO 6506-3:1999).
ISO 48, Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD and
100 IRHD).
ISO 4662, Rubber — Determination of rebound resilience of vulcanizates.
ISO 7619, Rubber — Determination of indentation hardness by means of pocket hardness meters.
ISO 7873, Control charts for arithmetic average with warning limits.
ISO 7966, Acceptance control charts.
ISO 8486-1, Bond abrasives — Determination and designation of grain size distribution — Macrogrits F4 to
F220.
3 Terms and definitions
For the purposes of this European Standard, the following terms and definitions apply.
3.1
arris
part of a block where two faces meet. It can be bevelled, rounded, chamfered, radiussed or splayed
3.2
concrete paving block
precast concrete unit used as a surfacing material that satisfies the following conditions:
at a distance of 50 mm from any edge, any cross-section does not show a horizontal dimension less
than 50 mm;
its overall length divided by its thickness is less than or equal to four.
NOTE These two conditions are not applicable to complementary fittings.
3.3
complementary fitting
unit, sometimes a part of a block, which is used to infill and enable an area to be completely surfaced
3.4
Permeable paving block
block complying with this standard with side features to provide wider joints for use in permeable pavements
3.5
overall length
longer side of the rectangle with the smallest area able to enclose the block excluding any spacer nibs
3.6
overall width
shorter side of the rectangle with the smallest area able to enclose the block excluding any spacer nibs
3.7
thickness
distance between the upper face and the bed face of the block
3.8
spacer nibs
small protruding profiles on a side face of a block
3.9
upper face
surface intended to be seen when in use
3.10
bed face
surface generally parallel to the upper face and in contact with the bedding after laying
3.11
facing layer
layer of concrete on the upper face of a block of different material and/or properties to the main body or
backing layer
NOTE To be distinguished from wipe, being a fine cement mortar or slurry applied to the surface of the block.
3.12
draw
intended angle of the side face from the vertical plane over the full height of a block as shown in Figure 1
α
Key
1 Chamfer 2 Thickness
α Draw
Figure 1 — Example of chamfer and draw
3.13
chamfer
bevelled arris, as shown in Figure 1
3.14
work dimension
any dimension of a block specified for its manufacture to which the actual dimension should conform within
specified permissible deviations
3.15
secondary processing
manufacturing process to texture the whole block or any surface, carried out after basic manufacture before
or after hardening
3.16
actual dimension
dimension of a block as measured
3.17
chased side face
side face of a concrete paving block, having a recessed profile
3.18
skid resistance
ability to resist relative movement between a vehicle tyre and the trafficked concrete paving block surface
3.19
slip resistance
ability to resist relative movement between a pedestrian foot and the trafficked concrete paving block surface
3.20
format
work dimensions of a block, specified in order of overall length, overall width and thickness
3.21
wipe
fine cement mortar or slurry applied to the surface of the units prior to curing
3.22
permeable block
block intended by its structure to allow the passage of water through the block. A permeable block may have
large voids intended to be filled with a drainage material of small interconnecting voids that allow water to
pass through.
4 Requirements for materials
4.1 General
Only materials with suitability established in terms of their properties and performance shall be used in the
manufacture of concrete paving blocks.
The suitability requirements of the materials used shall be given in the manufacturer’s production control
documentation.
Where, by conformity with relevant specifications, the properties and performance of materials have been
demonstrated, further testing need not be performed.
A reference scheme for materials inspection is given in annex A.
4.2 Asbestos
Asbestos, or materials containing asbestos, shall not be used.
5 Requirements for products
5.1 General
The performance requirements of concrete paving blocks are defined by classes which have associated
marking designations.
Blocks may be produced with a single concrete throughout or with different facing and backing layers.
When blocks are produced with a facing layer this shall have a minimum thickness of 4 mm over the area
declared by the manufacturer, when measured in accordance with Annex C. Isolated particles of aggregate
protruding into the facing layer shall be ignored. The facing layer shall be an integral part of the block.
A wipe shall only be carried out on a unit prior to curing, the constituents used shall be the same as in the
body of the block.
An arris described as square may be bevelled or rounded, its horizontal or vertical dimensions shall not
exceed 2,0 mm.
An arris with horizontal or vertical dimensions exceeding 2,0 mm shall be described as chamfered. Its
dimensions and tolerances shall be declared by the manufacturer.
Blocks may be produced with functional and/or decorative profiles, which shall not be included in the work
dimensions of a block.
The surface of blocks may be textured, secondary processed or treated chemically; these finishes or
treatments shall be described and decla
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.