iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 993-16:1995

(Main)

Dense shaped refractory products - Methods of test - Part 16: Determination of resistance to sulphuric acid

Dense shaped refractory products - Methods of test - Part 16: Determination of resistance to sulphuric acid

This part of EN 993 specifies a method for determining the resistance of dense shaped refractory products to attack by sulphuric acid. NOTE: Sulphuric acid is used since it gives results which are typical of the results of exposing refractory materials to many acids (other than hydrofluoric acid).

Prüfverfahren für dichte geformte feuerfeste Erzeugnisse - Teil 16: Bestimmung der Beständigkeit gegen Schwefelsäure

Dieser Teil von EN 993 legt ein Verfahren zur Bestimmung der Beständigkeit von dichten geformten feuerfesten Erzeugnissen gegen Angriff von Schwefelsäure fest. ANMERKUNG : Es wird Schwefelsäure verwendet, weil die mit ihr gewonnenen Ergebnisse (anders als bei Fluorwasserstoffsäure) üblich für die Ergebnisse des Angriffes von feuerfesten Werkstoffen durch Säuren sind.

Produits réfractaires façonnés denses - Méthode d'essai - Partie 16: Détermination de la résistance à l'acide sulfurique

La présente partie de l'EN 993 établit une méthode pour déterminer la résistance des produits réfractaires façonnés denses à l'attaque de l'acide sulfurique. NOTE : l'acide sulfurique est utilisé car il donne des résultats considérés comme caractéristiques de ceux qui sont obtenus en exposant des matériaux réfractaires à de nombreux acides (autres que l'acide fluorhydrique).

Gosti oblikovani ognjevzdržni izdelki - Preskusne metode - 16. del: Ugotavljanje odpornosti proti žvepleni kislini

General Information

Status
Published
Publication Date
01-Aug-1995
Withdrawal Date
28-Feb-1996
ICS
81.080 - Refractories
Technical Committee
CEN/TC 187 - Refractory products and materials
Drafting Committee
CEN/TC 187/WG 1 - Dense shaped refractory products
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
02-Nov-2022
Ref Project
SIST EN 993-16:1998 - Dense shaped refractory products - Methods of test - Part 16: Determination of resistance to sulphuric acid

Buy Standard

EN 993-16:1998EN 993-16:1998
PreviousNext
Standard
EN 993-16:1998
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-1998
Gosti oblikovani ognjevzdržni izdelki - Preskusne metode - 16. del: Ugotavljanje
odpornosti proti žvepleni kislini
Dense shaped refractory products - Methods of test - Part 16: Determination of
resistance to sulphuric acid
Prüfverfahren für dichte geformte feuerfeste Erzeugnisse - Teil 16: Bestimmung der
Beständigkeit gegen Schwefelsäure
Produits réfractaires façonnés denses - Méthode d'essai - Partie 16: Détermination de la
résistance a l'acide sulfurique
Ta slovenski standard je istoveten z: EN 993-16:1995
ICS:
81.080 Ognjevzdržni materiali Refractories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

-----------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 20182:2024(Main)
Refractory test-piece preparation - Gunning refractory panels by the pneumatic-nozzle mixing type guns (ISO 20182:2024)
SIST EN ISO 20182:2024

This document describes the procedure for the preparation of test panels from refractory materials by gunning through pneumatic nozzle mixing type guns at ambient temperatures. The test pieces are for the determination of properties on as-gunned products prepared under either “standard conditions” (as required for quality assurance or product development) or “site conditions”. In the case of “site conditions”, the purpose of the testing is to establish the properties pertaining to a given installation or a given set of installation conditions. In this case, the panel can be obtained during the on-site installation. Parameters such as ambient temperature, gunning elevation, air pressure and curing conditions (temperature, orientation of the panel) applicable during the preparation of the panel are as near as possible to the respective parameters pertaining to the site installation.
It is also possible to simulate certain “site conditions” by gunning panels off-site, for example, in a laboratory setting. This is acceptable under this document, by agreement between interested parties.
This document does not apply to plastic gunning mixes and to those mixes that contain aggregates that are susceptible to hydration.
This document does not apply to shotcrete type mixes, which are dealt with in ISO 18886.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21068-2:2024(Main)
Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 2: Determination of volatile components, total carbon, free carbon, silicon carbide, total and free silicon, free and surface silica (ISO 21068-2:2024)
SIST EN ISO 21068-2:2024

This document specifies analytical techniques for the determination of volatile components by thermal treatment at specified temperatures, and methods for the determination of the total carbon, free carbon, silicon carbide, total and free silicon and free and surface silica content of silicon-carbide, silicon-nitride and silicon-oxynitride containing raw materials and refractory products.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21068-3:2024(Main)
Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 3: Determination of nitrogen, oxygen and metallic and oxidic constituents (ISO 21068‑3:2024)
SIST EN ISO 21068-3:2024

This document specifies analytical techniques for the determination of total nitrogen and nitrogen calculated as silicon nitride, total oxygen, and metallic and oxidic components in silicon carbide raw materials and refractory products.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21068-4:2024(Main)
Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 4: XRD methods (ISO 21068‑4:2024)
SIST EN ISO 21068-4:2024

This document describes methods for the determination of mineralogical phases typically apparent in nitride and oxy-nitride bonded silicon carbide refractory products using a Bragg-Brentano diffractometer.
It includes details of sample preparations and general principles for qualitative and quantitative analyses of mineralogical phase composition. Quantitative determination of α-Si3N4, β-Si3N4, Si2ON2, AlN, and β’- SiAlON are described.
For quantitative determination of α-Si3N4, β-Si3N4, Si2ON2, AlN and β’-SiAlON refinement procedures based on the total nitrogen content of the sample are described.
NOTE            ISO 21068-3 is used for the analysis of the total nitrogen content of the sample.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8840:2024(Main)
Refractory materials - Determination of bulk density of granular materials (grain density) (ISO 8840:2021)
SIST EN ISO 8840:2024

This document specifies three methods for the determination of the bulk density of granular refractory materials (grain density) having a grain size larger than 2 mm:
—    Method 1: mercury method with vacuum;
—    Method 2: arrested water absorption method;
—    Method 3: vacuum method with spin dryer option according to ISO 5017.
Method 1 is intended as the reference method.
NOTE       Depending on the nature of the material tested, the three methods can give different results. Any statement of the value of a bulk density can therefore be accompanied by an indication of the method used or to be used in case of dispute.
The same method can be used for the determination of the volume of the sample, for selecting and preparing the sample, for calculating the bulk density and for presenting the test report.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21068-1:2024(Main)
Chemical analysis of raw materials and refractory products containing silicon-carbide, silicon-nitride, silicon-oxynitride and sialon - Part 1: General information, terminology and sample preparation (ISO 21068-1:2024)
SIST EN ISO 21068-1:2024

This document gives definitions and specifies techniques for the preparation of samples for the chemical analysis of silicon-carbide-containing raw materials and refractory products including:
a)       SiC raw materials;
b)       graphite brick containing silicon carbide;
c)        silicon carbide brick (includes the bricks containing silicon nitride, silicon oxynitride, sialon);
d)       refractories containing carbon and/or silicon carbide mixed with clay;
e)       refractories containing carbon and/or silicon carbide mixed with silica (and fused silica);
f)         refractories containing carbon and/or silicon carbide mixed with high alumina material;
g)       refractories containing carbon and/or silicon carbide mixed with magnesia (and dolomite);
h)       refractories containing carbon and/or silicon carbide mixed with chrome mineral or magnesia-chrome materials;
i)         refractories containing carbon and/or silicon carbide except those described in a) to h) above.
The items of analysis described in ISO 21068-2, ISO 21068-3 and ISO 21068-4 are as follows:
—     loss on drying (LOD);
—     loss on ignition (LOI);
—     total carbon, Ctotal;
—     free carbon, Cfree;
—     silicon carbide, SiC;
—     free silicon (Sifree);
—     free aluminium (Alfree);
—     free magnesium (Mgfree);
—     free iron (Fefree);
—     silicon(IV) dioxide (SiO2);
—     aluminium(III) oxide (Al2O3);
—     iron(III) oxide (Fe2O3);
—     titanium(IV) oxide (TiO2);
—     calcium oxide (CaO);
—     magnesium oxide (MgO);
—     sodium oxide (Na2O);
—     potassium oxide (K2O);
—     chromium(III) oxide (Cr2O3);
—     zirconium(IV) oxide (ZrO2);
—     boron oxide (total boron calculated as B2O3);
—     nitrogen;
—     oxygen;
—     nitrides (undifferentiated: Si3N4, AlN, BN, sialon, oxy-nitrides, etc.);
—     mineralogical phases (XRD-methods).

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 993-10:2020(Main)
Methods of test for dense shaped refractory products - Part 10: Determination of permanent change in dimensions on heating
SIST EN 993-10:2020

This document specifies three methods for the determination of the permanent change in dimensions on heating of dense shaped refractory products.
NOTE   The methods can be applied to materials sensitive to oxidation. However, some of these materials can be affected during the test in such a way as to make the measurement of the dimensional changes impossible to carry out to the required accuracy.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 993-5:2018(Main)
Methods of test for dense shaped refractory products - Part 5: Determination of cold crushing strength
SIST EN 993-5:2019

This document specifies a method of determination of the cold crushing strength of dense shaped refractory products.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 993-6:2018(Main)
Methods of test for (dense) shaped refractory products - Part 6: Determination of modulus of rupture at ambient temperature
SIST EN 993-6:2019

This Part of EN 993 specifies a method for the determination of the modulus of rupture of dense and insulating shaped refractory products at ambient temperature, under conditions of a constant rate of increase of stress.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    14 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 993-1:2018(Main)
Methods of test for dense shaped refractory products - Part 1: Determination of bulk density, apparent porosity and true porosity
SIST EN 993-1:2019

This document specifies a method for the determination of the bulk density, apparent porosity and true porosity of dense shaped refractory products.
NOTE   For shaped insulating refractory products, the bulk density and true porosity are determined in accordance with EN 1094-4.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day