EN ISO 14159:2008
(Main)Safety of machinery - Hygiene requirements for the design of machinery (ISO 14159:2002)
Safety of machinery - Hygiene requirements for the design of machinery (ISO 14159:2002)
This International Standard specifies hygiene requirements of machines and provides information for the intended use to be provided by the manufacturer. It applies to all types of machines and associated equipment used in applications where hygiene risks to the consumer of the product can occur.
This International Standard does not cover requirements relative to the uncontrolled egress of microbiological agents from the machine.
Sicherheit von Maschinen - Hygieneanforderungen an die Gestaltung von Maschinen (ISO 14159:2002)
Diese Internationale Norm legt Hygieneanforderungen für die Gestaltung von Maschinen fest und enthält Informationen zur vom Hersteller der Maschine bestimmte, vorgesehene Verwendung. Diese Norm gilt für alle Arten von Maschinen und die zugehörigen Ausrüstungen, bei deren Verwendung Hygienerisiken für den Konsumenten des Produkts entstehen können.
Anforderungen an die unkontrollierte Freisetzung mikrobiologischer Arbeitsstoffe durch die Maschine werden durch diese Internationale Norm nicht erfasst.
Sécurité des machines - Prescriptions relatives à l'hygiène lors de la conception des machines (ISO 14159:2002)
La présente Norme internationale spécifie les prescriptions relatives à l'hygiène lors de la conception des machines et donne des informations que le fabricant doit fournir pour l'utilisation prévisible. Elle s'applique à toutes les machines et équipements associés, utilisés dans des procédés où il existe des risques liés à l'hygiène pour le consommateur des produits.
La présente Norme internationale ne couvre pas les prescriptions relatives à la dissémination non maîtrisée des agents microbiens issus de la machine.
Varnost strojev - Higienske zahteve za načrtovanje strojev (ISO 14159:2002)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2008
1DGRPHãþD
SIST EN ISO 14159:2004
9DUQRVWVWURMHY+LJLHQVNH]DKWHYH]DQDþUWRYDQMHVWURMHY ,62
Safety of machinery - Hygiene requirements for the design of machinery (ISO
14159:2002)
Sicherheit von Maschinen - Hygieneanforderungen an die Gestaltung von Maschinen
(ISO 14159:2002)
Sécurité des machines - Prescriptions relatives à l'hygiène lors de la conception des
machines (ISO 14159:2002)
Ta slovenski standard je istoveten z: EN ISO 14159:2008
ICS:
13.110 Varnost strojev Safety of machinery
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 14159
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 13.110 Supersedes EN ISO 14159:2004
English Version
Safety of machinery - Hygiene requirements for the design of
machinery (ISO 14159:2002)
Sécurité des machines - Prescriptions relatives à l'hygiène
lors de la conception des machines (ISO 14159:2002)
This European Standard was approved by CEN on 21 March 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14159:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC .4
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .5
Foreword
The text of ISO 14159:2002 has been prepared by Technical Committee ISO/TC 199 “Safety of machinery” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 14159:2008 by
Technical Committee CEN/TC 114 “Safety of machinery” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at
the latest by October 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14159:2004.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directives.
For relationship with EC Directives, see informative Annex ZA and ZB which are integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 14159:2002 has been approved by CEN as a EN ISO 14159:2008 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential Requirements of
EU Directive 98/37/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive Machinery 98/37/EC, amended by 98/79/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a
presumption of conformity with the corresponding Essential Requirements of that Directive and associated
EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 98/37/EC
Clause(s)/sub-clause(s) of this EN Essential Requirements (ERs) of Qualifying remarks/Notes
Directive 98/37/EC, amended by
98/79/EC
All clauses Annex I, 2.1 Agri-foodstuffs machinery
WARNING — Other requirements and other EC Directives may be applicable to the product(s) falling within
the scope of this standard.
Annex ZB
(informative)
Relationship between this European Standard and the Essential Requirements of
EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive Machinery 2006/42/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard given in Table ZB.1 confers, within the limits of the scope of this standard, a
presumption of conformity with the corresponding Essential Requirements of that Directive and associated
EFTA regulations.
Table ZB.1 — Correspondence between this European Standard and Directive 2006/42/EC
Clause(s)/sub-clause(s) of this EN Essential Requirements (ERs) of Qualifying remarks/Notes
Directive 2006/42/EC
All clauses Annex I, 2.1 Foodstuffs machinery etc.
WARNING — Other requirements and other EC Directives may be applicable to the product(s) falling within
the scope of this standard.
INTERNATIONAL ISO
STANDARD 14159
First edition
2002-04-01
Safety of machinery — Hygiene
requirements for the design of machinery
Sécurité des machines — Prescriptions relatives à l'hygiène lors de la
conception des machines
Reference number
ISO 14159:2002(E)
©
ISO 2002
ISO 14159:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved
ISO 14159:2002(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 Normative references.1
3 Terms and definitions .1
4 Hazards.4
5 Hygiene requirements and/or measures.4
5.1 Strategy for selecting hygiene measures .4
5.2 Hygienic design .7
6 Verification of hygiene measures and test methods .11
7 Instruction handbook, maintenance and cleaning.11
7.1 Instruction handbook.11
7.2 Maintenance and cleaning.11
8 Additional information (limitations of use) .12
Annex A (informative) Categorization of machinery and associated equipment for intended use.13
Annex B (informative) Examples of good and bad hygienic design features.14
Annex C (informative) Relationship between International Standards referenced in clause 2 and
corresponding European Standards .29
Bibliography.30
ISO 14159:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14159 was prepared by Technical Committee ISO/TC 199, Safety of machinery.
Annexes A to C are for information only.
iv © ISO 2002 – All rights reserved
ISO 14159:2002(E)
Introduction
This International Standard is one of a series of standards relating to the safety of machinery (ISO 12100 series). It
differs from other safety standards, however, in that it is concerned with the associated hygiene risks of the
machinery to the consumer of the product being processed, not to the operator of the machine.
Hygiene risks are very different from other safety risks. They are more associated with the ability of machines to be
freed from product debris and micro-organisms, and thus preventing product contamination, rather than from the
dangers of moving parts or electrical hazards to the operator. For this reason, and whilst this International Standard
considers machines and their associated equipment, it can be used to provide guidance to the manufacturers of all
equipment types where hygiene risks to the consumer of products to be processed by such equipment could occur.
This International
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.