Soil quality - Determination of particle density (ISO 11508:2017)

ISO 11508:2017 specifies two methods for the determination of particle density of soils calculated from the mass and the volume of soil particles.
The first method (4.1) is applicable to fine soil (<2 mm diameter) and the second method (4.2) is applicable to both porous and nonporous gravel and stones (>2 mm diameter).
The particle density can be used for the calculation of the proportion of solids and of the porosity of soil layers in combination with the procedure given in ISO 11272.

Bodenbeschaffenheit - Bestimmung der Kornrohdichte (ISO 11508:2017)

Diese Internationale Norm legt zwei Verfahren zur Bestimmung der Kornrohdichte von Böden mittels Berechnung aus der Masse und dem Volumen von Bodenpartikeln, fest.
Das erste Verfahren (4.1) ist anwendbar auf Feinboden (< 2 mm Durchmesser), und das zweite Verfahren (4.2) ist anwendbar auf Böden, mit porösen und nichtporösen Kies- und Steinanteil (> 2 mm Durchmesser).
Die Kornrohdichte kann zur Berechnung des Anteils fester Substanz und der Porosität von Bodenschichten in Verbindung mit dem Verfahren nach ISO 11272 verwendet werden.

Qualité du sol - Détermination de la masse volumique des particules (ISO 11508:2017)

ISO 11508:2017 spécifie deux méthodes permettant de déterminer la masse volumique des particules qui constituent les sols, à partir de la masse et du volume de ces dernières.
La première méthode (4.1) est utilisable pour la terre fine (de diamètre <2 mm), et la seconde méthode (4.2) est utilisable pour les graviers et cailloux (de diamètre >2 mm) poreux ou non poreux.
La masse volumique des particules peut être utilisée, conjointement avec le mode opératoire spécifié dans l'ISO 11272, pour calculer la fraction de matière solide et la porosité des couches de sol.

Kakovost tal - Določevanje gostote delcev (ISO 11508:2017)

Ta dokument določa dve metodi za določevanje gostote delcev tal, ki se izračuna iz mase in prostornine delcev tal.
Prva metoda (4.1) se uporablja za drobnozrnata tla (premer < 2 mm), druga (4.2) pa se uporablja za porozen in neporozen gramoz ter kamenje (premer > 2 mm).
Gostota delcev se v kombinaciji s postopkom iz standarda ISO 11272 lahko uporabi za izračun deleža trdih delcev in poroznosti plasti tal.

General Information

Status
Published
Publication Date
21-Nov-2017
Withdrawal Date
30-May-2018
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
22-Nov-2017
Completion Date
22-Nov-2017

Relations

Buy Standard

Standard
EN ISO 11508:2018
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST EN ISO 11508:2014
SIST ISO 11508:2002
.DNRYRVWWDO'RORþHYDQMHJRVWRWHGHOFHY ,62
Soil quality - Determination of particle density (ISO 11508:2017)
Bodenbeschaffenheit - Bestimmung der Kornrohdichte (ISO 11508:2017)
Qualité du sol - Détermination de la masse volumique des particules (ISO 11508:2017)
Ta slovenski standard je istoveten z: EN ISO 11508:2017
ICS:
13.080.20 Fizikalne lastnosti tal Physical properties of soils
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11508
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2017
EUROPÄISCHE NORM
ICS 13.080.20 Supersedes EN ISO 11508:2014
English Version
Soil quality - Determination of particle density (ISO
11508:2017)
Qualité du sol - Détermination de la masse volumique Bodenbeschaffenheit - Bestimmung der Kornrohdichte
des particules (ISO 11508:2017) (ISO 11508:2017)
This European Standard was approved by CEN on 23 August 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11508:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
European foreword
This document (EN ISO 11508:2017) has been prepared by Technical Committee ISO/TC 190 “Soil
quality” in collaboration with Technical Committee CEN/TC 444 “Test methods for environmental
characterization of solid matrices” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be
withdrawn at the latest by May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11508:2014.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11508:2017 has been approved by CEN as EN ISO 11508:2017 without any modification.

INTERNATIONAL ISO
STANDARD 11508
Second edition
2017-09
Soil quality — Determination of
particle density
Qualité du sol — Détermination de la masse volumique des particules
Reference number
ISO 11508:2017(E)
©
ISO 2017
ISO 11508:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 11508:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Procedure. 1
4.1 Fine soil (<2 mm diameter) . 1
4.1.1 Principle . 1
4.1.2 Apparatus . 2
4.1.3 Sampling. 2
4.1.4 Density determination . 2
4.1.5 Calculation . 2
4.2 Gravel and stones (>2 mm diameter) . 3
4.2.1 Apparatus . 3
4.2.2 Density determination . 3
4.2.3 Calculation . 4
4.3 Unified reference temperature . 5
4.4 Calculation of mean particle density . 5
5 Test report . 5
Annex A (informative) Density of water at different temperatures . 6
Bibliography . 9
ISO 11508:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee is ISO/TC 190, Soil quality, Subcommittee SC 3,
Chemical methods and soil characteristics.
This second edition cancels and replaces the first edition (ISO 11508:1998), which has been technically
revised.
The main changes compared to the previous edition are as follows:
a) the terms and definitions have been updated;
b) a new subclause 4.3 “Unified reference temperature” was added;
c) a new subclause 4.4 “Calculation of mean particle density” was added;
d) Table 1, “Density of water…”, was deleted under 4.1.4;
e) a new Annex A “Density of water at different temperatures” was added;
f) bibliographic references were added;
g) editorial changes were made.
iv © ISO 2017 – All rights reserved

ISO 11508:2017(E)
Introduction
b
This document specifies the particle density (ρ ) which is used together with the dry bulk density (ρ ,
s s
see ISO 11272) for the calculation of the pore volume of a soil layer.
INTERNATIONAL STANDARD ISO 11508:2017(E)
Soil quality — Determination of particle density
1 Scope
This document specifies two methods for the determination of particle density of soils calculated from
the mass and the volume of soil particles.
The first method (4.1) is applicable to fine soil (<2 mm diameter) and the second method (4.2) is
applicable to both porous and nonporous gravel and stones (>2 mm diameter).
The particle density can be used for the calculation of the proportion of solids and of the porosity of soil
layers in combination with the procedure given in ISO 11272.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 565, Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes
of openings
ISO 11461, Soil quality — Determination of soil water content as a volume fraction using coring sleeves —
Gravimetric method
3 Terms and definitions
For the purposes of this document, the following terms and definition apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
3.1
particle density
ratio of the total mass of oven-dry solid particles, e.g. minerals or organic matter, to the volume of these
particles
Note 1 to entry: The volume comprises internal pores of soil particles but pore spaces b
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.