EN 4050-3:2012

Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 3: Reference blocks

This European Standard specifies the requirements for the manufacture, checking and marking of the series of ultrasonic testing reference blocks containing flat bottom holes (FBH) which define the indicated defect size to which reference is made in EN standards.
The application of ultrasonic testing reference blocks containing side drilled holes (SDH) which define an indicated defect size shall be agreed between manufacturer and purchaser.
This standard is applicable to the production of master and standard test blocks to be used when carrying out ultrasonic inspection to the requirements of EN 4050 1 (FBH method).
It is recognized that particular difficulties are encountered with round forging stock and bars due to the wide range of curvatures. For this application, only one block shall be produced to act as both master and standard test block.

Luft- und Raumfahrt - Prüfverfahren für metallische Werkstoffe - Ultraschallprüfung von Stangen, Platten, Schmiedevormaterial und Schmiedestücken - Teil 3: Referenzblöcke

Diese Europäische Norm legt die Anforderungen an Herstellung, Überprüfung und Kennzeichnung der Serie von Ultraschallprüfungs-Referenzblöcken mit Flachbodenbohrungen (FBH) fest, welche die angezeigte Fehlergröße definieren, auf die in EN-Normen verwiesen wird.

Série aérospatiale - Méthode d'essai applicable aux matériaux métalliques - L'inspection par ultrasons des barres, des plaques, des stocks de forgeage et de pièces forgées - Partie 3: Blocs de référence

Aeronavtika - Metode za preskušanje kovinskih materialov - Ultrazvočno preskušanje palic, plošč, kovnih materialov in izkovkov - 3. del: Referenčni ingoti

General Information

• Status: Published
• Publication Date: 25-Sep-2012
• Withdrawal Date: 30-Mar-2013
• ICS: 49.025.05 - Ferrous alloys in general
• ICS: 49.025.15 - Non-ferrous alloys in general
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 4 - Metallic
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 26-Sep-2012
• Completion Date: 26-Sep-2012
• Ref Project: SIST EN 4050-3:2014 - Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 3: Reference blocks

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.YRþQRLuft- und Raumfahrt - Prüfverfahren für metallische Werkstoffe - Ultraschallprüfung von Stangen, Platten, Schmiedevormaterial und Schmiedestücken - Teil 3: ReferenzblöckeSérie aérospatiale - Méthode d'essai applicable aux matériaux métalliques - L'inspection par ultrasons des barres, des plaques, des stocks de forgeage et de pièces forgées - Partie 3: Blocs de référenceAerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 3: Reference blocks49.035Sestavni deli za letalsko in vesoljsko gradnjoComponents for aerospace construction49.025.01Materiali za letalsko in vesoljsko gradnjo na splošnoMaterials for aerospace construction in generalICS:Ta slovenski standard je istoveten z:EN 4050-3:2012SIST EN 4050-3:2014en01-marec-2014SIST EN 4050-3:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4050-3
September 2012 ICS 49.025.05; 49.025.15 English Version
Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings -Part 3: Reference blocks
Série aérospatiale - Méthode d'essai applicable aux matériaux métalliques - L'inspection par ultrasons des barres, des assiettes, des stocks de forgeage et de pièces forgées - Partie 3: Blocs de référence
Luft- und Raumfahrt - Prüfverfahren für metallische Werkstoffe - Ultraschallprüfung von Stangen, Platten, Schmiedevormaterial und Schmiedestücken - Teil 3: Referenzblöcke This European Standard was approved by CEN on 15 July 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4050-3:2012: ESIST EN 4050-3:2014

Standard test blocks. 10A.1Specification . 10A.2Examples of standard test blocks. 10 SIST EN 4050-3:2014

1) Published as ASD-STAN Standard at the date of publication of this standard. 2) Published as ASD-STAN Prestandard at the date of publication of this standard. 3) Published by: American Society for Testing and Materials (ASTM) 1916 Race Street, Philadelphia, PA. SIST EN 4050-3:2014

5.2 Flat bottom holes standards Flat bottom holes in the master test blocks shall be used to calibrate standard test blocks. The master test blocks shall have FBH at different metal paths to suit the product range to be inspected. It shall be ensured however that there is sufficient number with a minimum of three different metal paths to accurately produce the required distance/amplitude curve (see 5.4.2.2). 5.3 Manufacture 5.3.1 Material procurement Material for each set of master test blocks shall be obtained from the same cast, forging and heat treatment batch. For longitudinal waves when checking anisotropic materials, the FBH shall be drilled perpendicular to the grain flow, if possible, but always perpendicular to the surface. Ultrasonic tests shall be carried out on each test block to ensure:  freedom from defects greater than or equal to − 12 dB below the DAC (see EN 4050-1);  consistent grass level across each test block and between master test blocks in the vicinity of the FBH. Maximum variation ± 3 dB;  consistent attenuation across each test block and between master test blocks not to exceed 0,1 dB/cm variation. SIST EN 4050-3:2014
...