Aerospace series - Clamps, loop ("P" type) in aluminium alloy with rubber cushioning - Dimensions, masses

This document specifies the required characteristics of loop style clamps ("P" type) in aluminium alloy with various cushion materials.
These clamps are used for supporting aerospace pipe assemblies and electrical cable bundles.
They are used up to 80 °C max.
Usage at a higher temperature is at the option of the user.
For temperature range and environmental considerations, see the various cushion material standards.

Luft- und Raumfahrt - Schellen in Schlaufenform (P-Form) aus Aluminiumlegierung mit Profilgummi - Maße, Massen

Dieses Dokument legt die Anforderungen an Schellen in Schlaufenform (P-Form) aus Aluminiumlegierung mit verschiedenen Profilgummi-Werkstoffen fest.
Diese Schellen werden zur Halterung von Rohrleitungen und elektrischen Leitungsbündeln in der Luft- und Raumfahrt verwendet.
Sie werden bis zu einer Temperatur von höchstens 80 °C verwendet.
Die Verwendung bei höherer Temperatur erfolgt nach Wahl des Anwenders.
Für den Temperaturbereich und die Umweltbedingungen siehe die Angaben in den jeweiligen Werkstoffnormen für Profilgummi.

Série aérospatiale - Colliers, boucle en P en alliage d’aluminium avec profilé en élastomère - Dimensions, masses

Le présent document spécifie les caractéristiques requises pour les colliers à boucle en P, en alliage d’aluminium, avec différents matériaux pour les profilés (garnitures).
Ces colliers sont utilisés pour maintenir les tuyauteries et les faisceaux de câbles électriques à usage aérospatial.
Ils sont utilisés jusqu'à 80 °C max.
L’utilisation à une température plus élevée est au choix de l’utilisateur.
Pour les plages de températures et les conditions environnementales, voir les normes des différents matériaux pour les profilés.

Aeronavtika - Objemke v obliki zanke (P-oblika) iz aluminijeve zlitine z zaščitno prevleko iz gume - Mere, mase

Ta dokument določa zahtevane značilnosti objemk v obliki zanke (P-oblika) iz aluminijeve zlitine s prevlekami iz različnih materialov.
Te objemke se uporabljajo za podporo aeronavtičnih cevnih sklopov in snopov električnih kablov.
Uporabljajo se pri temperaturi največ 80 °C.
Uporaba pri višji temperaturi je izbira uporabnika.
Za temperaturno območje in okoljske vidike glej standarde o prevlekah iz različnih materialov.

General Information

Status
Published
Publication Date
19-Dec-2023
Technical Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Dec-2023
Completion Date
20-Dec-2023

Relations

Buy Standard

Standard
EN 4114:2024
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2024
Aeronavtika - Objemke v obliki zanke (P-oblika) iz aluminijeve zlitine z zaščitno
prevleko iz gume - Mere, mase
Aerospace series - Clamps, loop ("P" type) in aluminium alloy, with rubber cushioning -
Dimensions, masses
Luft- und Raumfahrt - Schellen in Schlaufenform (P-Form) aus Aluminiumlegierung mit
Profilgummi - Maße, Massen
Série aérospatiale - Colliers en “P” en alliage d’aluminium avec profilé en élastomère -
Dimensions, masses
Ta slovenski standard je istoveten z: EN 4114:2023
ICS:
49.025.20 Aluminij Aluminium
49.025.40 Guma in polimerni materiali Rubber and plastics
49.030.99 Drugi vezni elementi Other fasteners
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 4114
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2023
EUROPÄISCHE NORM
ICS 49.030.99 Supersedes EN 4114:2009
English Version
Aerospace series - Clamps, loop ("P" type) in aluminium
alloy with rubber cushioning - Dimensions, masses
Série aérospatiale - Colliers, boucle en P en alliage Luft- und Raumfahrt - Schellen in Schlaufenform (P-
d'aluminium avec profilé en élastomère - Dimensions, Form) aus Aluminiumlegierung mit Profilgummi -
masses Maße, Massen
This European Standard was approved by CEN on 15 October 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4114:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Required characteristics . 5
4.1 Materials . 5
4.2 Surface treatment . 5
4.3 Configuration – Dimensions – Masses . 5
5 Designation . 10
6 Marking . 10
7 Technical specification . 10

European foreword
This document (EN 4114:2023) has been prepared by the Aerospace and Defence Industries Association
of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2024, and conflicting national standards shall be
withdrawn at the latest by June 2024.
This document supersedes EN 4114:2009.
— normative references were updated;
— abbreviation “FPM” was changed to “FKM” throughout the document.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
1 Scope
This document specifies the required characteristics of loop style clamps (“P” type) in aluminium alloy
with various cushion materials.
These clamps are used for supporting aerospace pipe assemblies and electrical cable bundles.
They are used
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.