EN 2545-3:1995
(Main)Aerospace series - Titanium and titanium alloy remelting stock and castings - Technical specification - Part 3: Pre-production and production castings
Aerospace series - Titanium and titanium alloy remelting stock and castings - Technical specification - Part 3: Pre-production and production castings
This standard specifies the particular requirements for pre-production and production castings in titanium and titanium alloys. This standard shall be usedin conjunction with EN 2545-1. Where remelting stock is used it shall conform toEN 2545-2. Unless otherwise required by the order, drawing or inspection schedule, the castings shall be supplied to quality level 2 (see table 3).
Luft- und Raumfahrt - Vormaterial und Gußstücke aus Titan und Titanlegierungen - Technische Lieferbedingungen - Teil 3: Ausfallmuster- und Seriengußstücke
Diese Norm legt die Sonderanforderungen an Ausfallmuster- und Seriengußstücke aus Titan und Titanlegierungen fest. Diese Norm ist in Verbindung mit EN 2545-1 anzuwenden, muß dieses EN 2545-2 entsprechen. Sofern in der Bestellung Zeichnung oder Prüfanweisung nichts anderes festgelegt ist, werden Gußstücke entsprechend Qualitätsniveau 2 geliefert (siehe Tabelle 3).
Série aérospatiale - Produits pour refusion et pièces moulées en titane et alliages de titane - Spécification technique - Partie 3: Pièces types et pièces de série
La présente norme spécifie les exigences particulières pour les pièces types et de séries moulées en titane et alliages de titane. La présente norme doit être utilisée en conjonction avec EN 2545-1. Dans ce cas où des produits pour refusion sont utilisés, ils doivent être conformes à EN 2545-2. Sauf indicationparticulière sur la commande, le dessin ou la fiche d'essais, les pièces mouléesdoivent être approvisionnées au niveau de qualité 2 (voir tableau 3).
Aerospace series - Titanium and titanium alloy remelting stock and castings - Technical specification - Part 3: Pre-production and production castings
General Information
- Status
- Published
- Publication Date
- 30-May-1995
- Withdrawal Date
- 29-Nov-1995
- Technical Committee
- ASD-STAN - Aerospace
- Drafting Committee
- ASD-STAN/D 4 - Metallic
- Current Stage
- 6060 - Definitive text made available (DAV) - Publishing
- Start Date
- 31-May-1995
- Completion Date
- 31-May-1995
Overview
EN 2545-3:1995 (Aerospace series) is a CEN technical specification that defines the particular requirements for pre-production and production castings made from titanium and titanium alloys. It is intended to be used in conjunction with EN 2545-1 (general requirements) and, where remelting stock is involved, with EN 2545-2. Unless otherwise specified by contract, drawing or inspection schedule, castings supplied under EN 2545-3 are to be delivered to quality level 2.
This standard is aimed at ensuring repeatable, auditable practices for the supply and acceptance of titanium castings used in aerospace applications, helping manufacturers and purchasers meet consistent quality and traceability expectations.
Key Topics and Requirements
EN 2545-3 focuses on the particular requirements that apply specifically to pre-production and production castings of titanium alloys. Important areas covered include:
- Scope and applicability for pre-production and production castings in titanium and titanium alloys.
- Integration with EN 2545-1 and EN 2545-2, specifying how parts of the aerospace series work together.
- Quality level designation - default supply quality is quality level 2 unless overridden by contractual documents.
- Inspection and acceptance - requirements tied to order, drawing, and inspection schedules that determine acceptance criteria.
- Traceability and documentation - obligations for record keeping and material identification aligned with aerospace procurement needs.
- Control of production - provisions addressing the transition from pre-production (development) to full production castings.
Note: EN 2545-3 specifies particular requirements but relies on EN 2545-1 for the general technical framework and EN 2545-2 for remelting stock specifications.
Practical Applications
Who uses EN 2545-3 and why:
- Aerospace manufacturers and prime contractors - to specify acceptable casting supply conditions for structural and engine-related titanium parts.
- Foundries and casting suppliers - to ensure supplied castings meet aerospace purchase orders and inspection schedules.
- Quality and procurement engineers - to define acceptance criteria, documentation, and traceability for titanium castings.
- Design and manufacturing engineers - to align casting procurement with production readiness and qualification plans.
Typical uses include specifying requirements for prototype and production runs of titanium components where aerospace-grade quality and consistent supply procedures are essential.
Related Standards
- EN 2545-1 - Titanium and titanium alloy remelting stock and castings: general technical specification (use in conjunction).
- EN 2545-2 - Remelting stock requirements for titanium and titanium alloys (applies where remelting stock is used).
Keywords: EN 2545-3, titanium castings, aerospace titanium, pre-production castings, production castings, remelting stock, quality level 2, CEN standard.
Frequently Asked Questions
EN 2545-3:1995 is a standard published by the European Committee for Standardization (CEN). Its full title is "Aerospace series - Titanium and titanium alloy remelting stock and castings - Technical specification - Part 3: Pre-production and production castings". This standard covers: This standard specifies the particular requirements for pre-production and production castings in titanium and titanium alloys. This standard shall be usedin conjunction with EN 2545-1. Where remelting stock is used it shall conform toEN 2545-2. Unless otherwise required by the order, drawing or inspection schedule, the castings shall be supplied to quality level 2 (see table 3).
This standard specifies the particular requirements for pre-production and production castings in titanium and titanium alloys. This standard shall be usedin conjunction with EN 2545-1. Where remelting stock is used it shall conform toEN 2545-2. Unless otherwise required by the order, drawing or inspection schedule, the castings shall be supplied to quality level 2 (see table 3).
EN 2545-3:1995 is classified under the following ICS (International Classification for Standards) categories: 49.025.30 - Titanium. The ICS classification helps identify the subject area and facilitates finding related standards.
You can purchase EN 2545-3:1995 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Titanium and titanium alloy remelting stock and castings - Technical specification - Part 3: Pre-production and production castingsLuft- und Raumfahrt - Vormaterial und Gußstücke aus Titan und Titanlegierungen - Technische Lieferbedingungen - Teil 3: Ausfallmuster- und SeriengußstückeSérie aérospatiale - Produits pour refusion et pieces moulées en titane et alliages de titane - Spécification technique - Partie 3: Pieces types et pieces de sérieAerospace series - Titanium and titanium alloy remelting stock and ca
...
이 기사는 EN 2545-3:1995 표준에 대해 논의하고 있습니다. 이 표준은 항공 용도로 사용되는 티타늄 및 티타늄 합금 주조물에 대한 특정 요구 사항을 명시하고 있습니다. 이 표준은 EN 2545-1과 함께 사용되어야 합니다. 재용해 재고를 사용하는 경우 EN 2545-2에 준수해야 합니다. 주문, 도면 또는 검사 일정에서 요구사항이 없는 한, 주조물은 품질 레벨 2로 제공되어야 합니다(표 3 참조).
この記事では、EN 2545-3:1995の基準について説明しています。この基準は、航空機用のチタンやチタン合金の鋳造品に関する特定の要件を示しています。この基準はEN 2545-1と共に使用する必要があります。リメルトストックを使用する場合は、EN 2545-2に準拠する必要があります。注文書、図面、検査スケジュールで別に要求がない限り、鋳造品は品質レベル2で提供される必要があります（表3参照）。
The article discusses the EN 2545-3:1995 standard, which pertains to titanium and titanium alloy castings for aerospace purposes. The standard specifies the specific requirements for pre-production and production castings. It must be used along with EN 2545-1, and if remelting stock is used, it must conform to EN 2545-2. The castings are expected to meet quality level 2, unless otherwise stated in the order, drawing, or inspection schedule.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...