EN ISO 20567-2:2006
(Main)Paints and varnishes - Determination of stone-chip resistance of coatings - Part 2: Single-impact test with a guided impact body (ISO 20567-2:2005)
Paints and varnishes - Determination of stone-chip resistance of coatings - Part 2: Single-impact test with a guided impact body (ISO 20567-2:2005)
ISO 20567-2:2005 specifies a method for the evaluation of the resistance of automobile finishes and other coatings to the impact of a wedge-shaped body projected onto the surface under test to simulate the impact of stones.
Beschichtungsstoffe - Prüfung der Steinschlagfestigkeit von Beschichtungen - Teil 2: Einzelschlagprüfung mit geführtem Schlagkörper (ISO 20567-2:2005)
Peintures et vernis - Détermination de la résistance des revêtements aux impacts de cailloux - Partie 2: Essai de choc simple par corps de choc à vol conduit (ISO 20567-2:2005)
L'ISO 20567-2:2005 spécifie une méthode d'évaluation de la résistance des revêtements, notamment ceux utilisés pour la finition des carrosseries de voitures, à la projection d'un corps en forme de coin contre la surface soumise à l'essai, destinée à simuler l'impact de cailloux.
Barve in laki - Ugotavljanje odpornosti premazov proti udarcem kamenja – 2. del: Preskus z enim udarcem vodenega telesa (ISO 20567-2:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2007
Barve in laki - Ugotavljanje odpornosti premazov proti udarcem kamenja – 2. del:
Preskus z enim udarcem vodenega telesa (ISO 20567-2:2005)
Paints and varnishes - Determination of stone-chip resistance of coatings - Part 2: Single
-impact test with a guided impact body (ISO 20567-2:2005)
Beschichtungsstoffe - Prüfung der Steinschlagfestigkeit von Beschichtungen - Teil 2:
Einzelschlagprüfung mit geführtem Schlagkörper (ISO 20567-2:2005)
Peintures et vernis - Détermination de la résistance des revetements aux impacts de
cailloux - Partie 2: Essai de choc simple par corps de choc a vol conduit (ISO 20567-
2:2005)
Ta slovenski standard je istoveten z: EN ISO 20567-2:2006
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 20567-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2006
ICS 87.040
English Version
Paints and varnishes - Determination of stone-chip resistance of
coatings - Part 2: Single-impact test with a guided impact body
(ISO 20567-2:2005)
Peintures et vernis - Détermination de la résistance des Beschichtungsstoffe - Prüfung der Steinschlagfestigkeit von
revêtements aux impacts de cailloux - Partie 2: Essai de Beschichtungen - Teil 2: Einzelschlagprüfung mit geführtem
choc simple par corps de choc à vol conduit (ISO 20567- Schlagkörper (ISO 20567-2:2005)
2:2005)
This European Standard was approved by CEN on 11 September 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20567-2:2006: E
worldwide for CEN national Members.
Foreword
The text of ISO 20567-2:2005 has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes” of the International Organization for Standardization (ISO) and has been taken
over as EN ISO 20567-2:2006 by Technical Committee CEN/TC 139 "Paints and varnishes", the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by April 2007, and conflicting national
standards shall be withdrawn at the latest by April 2007.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 20567-2:2005 has been approved by CEN as EN ISO 20567-2:2006 without any
modifications.
INTERNATIONAL ISO
STANDARD 20567-2
First edition
2005-02-15
Paints and varnishes — Determination
of stone-chip resistance of coatings —
Part 2:
Single-impact test with a guided impact
body
Peintures et vernis — Détermination de la résistance des revêtements
aux impacts de cailloux —
Partie 2: Essai de choc simple par corps de choc à vol conduit
Reference number
ISO 20567-2:2005(E)
©
ISO 2005
ISO 20567-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
ISO 20567-2:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Principle . 1
4 Apparatus and materials . 2
5 Sampling . 2
6 Test panels . 2
7 Procedure . 4
8 Evaluation . 5
9 Precision . 6
10 Test report . 7
Annex A (normative) Calibration of the test apparatus. 8
ISO 20567-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 20567-2 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 9,
General test methods for paints and varnishes.
ISO 20567 consists of the following parts, under the general title Paints and varnishes — Determination of
stone-chip resistance of coatings:
Part 1: Multi-impact testing
Part 2: Single-impact test with a guided impact body
iv © ISO 2005 – All rights reserved
ISO 20567-2:2005(E)
Introduction
In the automobile industry, multi-layer paint coatings are applied to car bodies for protection. Grit, road-metal
and other materials can damage these coatings in such a way that individual layers come off or the whole
coating delaminates from the substrate.
Stone chipping can be simulated by means of single- and/or multi-impact tests. Part 1 of this International
Standard describes multi-impact testing, Part 2 describes a single-impact test.
This part of ISO 20567 is based on the German Standard DIN 55996-2:2001, Beschichtungsstoffe — Prüfung
der Steinschlagfestigkeit von Beschichtungen — Teil 2: Einzelschlagprüfung (Paints and varnishes — Stone
chip resistance t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.