FprEN 3375-011
(Main)Aerospace series - Cable, electrical for digital data transmission - Part 011: Single braid - Star Quad 100 ohms - Lightweight - Type KL - Product standard
Aerospace series - Cable, electrical for digital data transmission - Part 011: Single braid - Star Quad 100 ohms - Lightweight - Type KL - Product standard
This document specifies the dimensions, tolerances, required characteristics and the mass of an AWG 24 shielded quad cable, type KL, intended for high speed (100 Mbit/s) full duplex Ethernet networks.
Linked to this particular application, the operating temperatures of the cable are between −65 °C and 125 °C.
This cable is laser markable, this marking satisfies the requirements of EN 3838.
The characteristics impedance is 100 Ω ± 15 Ω.
Luft- und Raumfahrt - Elektrische Leitungen für Digitaldatenübertragungen - Teil 011: Einfach geschirmt - Sternvierer 100 Ohm - Leichtbauweise - Typ KL - Produktnorm
Série aérospatiale - Câbles électriques pour transmission de données numériques - Partie 011 : Simple tresse - Quarte en étoile 100 ohms - Allégée - Type KL - Norme de produit
Le présent document spécifie les dimensions, les tolérances, les caractéristiques requises et la masse d’un câble blindé à quarte en étoile AWG 24, de type KL, destiné aux réseaux Ethernet haut débit (100 Mbit/s) en duplex intégral.
En lien avec cette application spécifique, les températures d’utilisation du câble se situent entre -65 °C et 125 °C.
Il est possible d’appliquer un marquage par laser sur ce câble. Ce marquage satisfait aux exigences de l’EN 3838.
L’impédance caractéristique est de 100 Ω ± 15 Ω.
Aeronavtika - Električni kabli za digitalni prenos podatkov - 011. del: Enojni oplet - Štirižilni zvezdasti kabel, 100 ohm - Lahki - Tip KL - Standard za proizvod
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 3375-011:2023
01-september-2023
Aeronavtika - Električni kabli za digitalni prenos podatkov - 011. del: Enojni oplet -
Štirižilni zvezdasti kabel, 100 ohm - Lahki - Tip KL - Standard za proizvod
Aerospace series - Cable, electrical for digital data transmission - Part 011: Single braid -
Star Quad 100 ohms - Lightweight - Type KL - Product standard
Luft- und Raumfahrt - Elektrische Leitungen für Digitaldatenübertragungen - Teil 011:
Einfach geschirmt - Sternvierer 100 Ohm - Leichtbauweise - Typ KL - Produktnorm
Série aérospatiale - Câbles électriques pour transmission de données numériques -
Partie 011 : Simple tresse - Quarte en étoile 100 ohms - Allégée - Type KL - Norme de
produit
Ta slovenski standard je istoveten z: prEN 3375-011
ICS:
29.060.20 Kabli Cables
49.060 Letalska in vesoljska Aerospace electric
električna oprema in sistemi equipment and systems
oSIST prEN 3375-011:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN 3375-011:2023
oSIST prEN 3375-011:2023
DRAFT
EUROPEAN STANDARD
prEN 3375-11
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2023
ICS 49.060; 49.090 Will supersede EN 3375-011:2022
English Version
Aerospace series - Cable, electrical for digital data
transmission - Part 011: Single braid - Star Quad 100 ohms
- Lightweight - Type KL - Product standard
Série aérospatiale - Câbles électriques pour Luft- und Raumfahrt - Elektrische Leitungen für
transmission de données numériques - Partie 011 : Digitaldatenübertragungen - Teil 011: Einfach
Simple tresse - Quarte en étoile 100 ohms - Allégée - geschirmt - Sternvierer 100 Ohm - Leichtbauweise -
Type KL - Norme de produit Typ KL - Produktnorm
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 3375-11:2023 E
worldwide for CEN national Members.
oSIST prEN 3375-011:2023
prEN 3375-011:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Required characteristics . 5
4.1 Configuration, dimensions, tolerances and mass. 5
4.2 Material . 5
4.3 General characteristics . 6
5 Tests . 6
6 Quality assurance . 11
7 Identification and marking (according to EN 3375-002 and TR 6058) . 12
7.1 Designation . 12
7.2 Short designation . 12
7.3 Marking on cable . 12
7.4 Colour of the marking on the jacket . 12
7.5 Colour of components . 12
8 Packaging . 13
9 Technical specification . 13
Annex A (informative) Standard evolution form . 14
Bibliography . 15
oSIST prEN 3375-011:2023
prEN 3375-011:2023 (E)
European foreword
This document (prEN 3375-011:2023) has been prepared by the Aerospace and Defence Industries
Association of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 3375-011:2022.
The main changes with respect to the previous edition are as follows:
— prEN 3774-001 (P4), XX/202X — Editorial improvements and update of Table 3 to make “Filler”
optional.
oSIST prEN 3375-011:2023
prEN 3375-011:2023 (E)
1 Scope
This document specifies the dimensions, tolerances, required characteristics and the mass of an
AWG 24 shielded quad cable, type KL, intended for high speed (100 Mbit/s) full duplex Ethernet
networks.
Linked to this particular application, the operating temperatures of the cable are between −65 °C and
125 °C.
This cable is laser markable, this marking satisfies the requirements of EN 3838.
The characteristics impedance is 100 Ω ± 15 Ω.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 3375-001, Aerospace series — Cable, electrical, for digital data transmission — Part 001: Technical
specification
EN 3375-002, Aerospace series — Cable, electrical, for digital data transmission — Part 002: General
*
EN 3475- , Aerospace series — Cables, electrical, aircraft use — Test methods
TR 6058, Aerospace series — Cable code identification list
3 Terms and definitions
For the purposes of this document the terms and definitions given in EN 3475-100 apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
* All parts quoted in this document.
Published as ASD-STAN Technical Report at the date of publication of this document by AeroSpace and Defence
industries Association of Europe — Standardization (ASD-STAN), https://www.asd-stan.org/.
oSIST prEN 3375-011:2023
prEN 3375-011:2023 (E)
4 Required characteristics
4.1 Configuration, dimensions, tolerances and mass
The configuration, dimensions and tolerances shall be in accordance with Figure 1 and Table 1.
Mass: ≤ 32,4 g/m.
Dimensions are in millimetres
NOTE No. of elements in accordance with Table 2.
Figure 1 — Configuration, dimensions and tolerances
Table 1 — Dimensions, tolerances and general characteristics
Stranded conductor (∅ A) a
0,598 mm ≤ ∅ ≤ 0,656 mm
Insulation diameter (single wire) a
∅ ≤ 1,52 mm
Braid, shield Strand diameter: ≥ 0,08 mm
Outer diameter of cable (∅ B) 4,10 mm < ∅ < 4,50 mm
Light blue
Colour of the jacket
Pair 1: Red (+), Blue (−)
Colour of components
Pair 2: Yellow (+), Green (−)
Minimum bending radius for dynamic installation 10 × Max. outer diameter
Minimum bending radius in static 5 × Max. outer diameter
a
Adapted tools are requested for stripping.
4.2 Material
The material and surface treatment shall be in accordance with Table 2.
oSIST prEN 3375-011:2023
prEN 3375-011:2023 (E)
Table 2 — Material
No. of element Element Material
Stranded conductor Silver plated copper
Insulation Fluoropolymer
Protection tape (optional) Sy
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.