CEN/TS 14758-2:2016
(Main)Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 2: Guidance for the assessment of conformity
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 2: Guidance for the assessment of conformity
This Technical Specification gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 14758 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 14758 1 this document is applicable to solid wall piping systems made of polypropylene modified with mineral(s) (PP-MD) intended to be used for:
— non-pressure underground drainage and sewerage outside the building structure (application area code “U”); and
— non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code “D”) and outside the building structure.
This is reflected in the marking of products by “U” and “UD”.
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Diese Technische Spezifikation gibt Empfehlungen für die Beurteilung der Konformität von Werkstoffen, Erzeugnissen, Verbindungen und Bauteilkombinationen, die, in Übereinstimmung mit den/dem entsprechenden Teil(en) von EN 14758, für eine Einbeziehung in den Qualitäts-sicherungsplan des Herstellers als Teil des Qualitätsmanagementsystems und für die Erstellung von Zertifizierungsverfahren vorgesehen sind.
ANMERKUNG Zur Unterstützung der Leser enthält Anhang A einen Überblick über das Prüfsystem.
Dieses Dokument gilt in Verbindung mit EN 14758-1 für Vollwand-Rohrleitungssysteme aus Polypropylen mit mineralischen Additiven (PP-MD), die für folgende Verwendungszwecke vorgesehen sind:
— für erdverlegte drucklose Abwasserkanäle und -leitungen für Anwendungen außerhalb der Gebäudestruktur (Anwendungskennzeichen „U“); und
— für erdverlegte drucklose Abwasserkanäle und -leitungen für Anwendungen sowohl erdverlegt innerhalb der Gebäudestruktur (Anwendungs¬kennzeichen „D“) als auch außerhalb der Gebäude-struktur.
Dies wird durch die Kennzeichnung auf dem Erzeugnis durch „U“ und „UD“ angezeigt.
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène avec modificateurs minéraux (PP-MD) - Partie 2 : Guide pour l'évaluation de la conformité
La présente spécification technique fournit un guide pour l’évaluation de conformité des matières, produits, assemblages et montages en conformité avec la (les) partie(s) appropriée(s) de l'EN 14758 destiné à être inclus dans le plan qualité du fabricant dans le cadre du système de management de la qualité et pour l'établissement des procédures de certification.
NOTE Afin d'aider le lecteur, une matrice d'essais de base est fournie en Annexe A.
Conjointement avec l'EN 14758 1, le présent document s'applique aux systèmes de canalisations à paroi compacte en polypropylène avec modificateurs minéraux (PP MD) destinés à être utilisés pour:
— les branchements et les collecteurs d'assainissement sans pression enterrés à l'extérieur de la structure du bâtiment (code de zone d'application « U ») ; et
— les branchements et les collecteurs d’assainissement sans pression enterrés aussi bien à l’intérieur de la structure du bâtiment (code de zone d’application « D ») qu’à l’extérieur de la structure du bâtiment.
Ceci se traduit dans le marquage des produits par « U » et « UD ».
Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) - 2. del: Smernice za ugotavljanje skladnosti
Ta tehnična specifikacija podaja navodila za ugotavljanje skladnosti materialov, proizvodov, spojev in sestavov v skladu z ustreznimi deli standarda EN 14758, pri čemer naj bi se te informacije vključile v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti in za vzpostavitev postopka certificiranja. Ta dokument se v povezavi s standardom EN 14758-1 uporablja za cevne sisteme v trdnih stenah, izdelane iz polipropilena z mineralnim modifikatorjem (PP-MD), ki naj bi se uporabljali za: – podzemne sisteme odvodnjavanja in kanalizacijske sisteme zunaj stavbne konstrukcije, ki delujejo po težnostnem principu (koda območja uporabe »U«), in – podzemne sisteme odvodnjavanja in kanalizacijske sisteme, ki delujejo po težnostnem principu in so vkopani v zemljo znotraj stavbne konstrukcije (koda območja uporabe »D«) in zunaj nje. To je razvidno iz oznak »U« in »UD« na proizvodih.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2016
1DGRPHãþD
SIST-TS CEN/TS 14758-2:2007
Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo
po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) - 2. del:
Smernice za ugotavljanje skladnosti
Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene with mineral modifiers (PP-MD) - Part 2: Guidance for the assessment of
conformity
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 2: Empfehlungen für
die Beurteilung der Konformität
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement enterrés sans pression - Polypropylène avec modificateurs minéraux
(PP-MD) - Partie 2 : Guide pour l'évaluation de la conformité
Ta slovenski standard je istoveten z: CEN/TS 14758-2:2016
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN/TS 14758-2
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
July 2016
TECHNISCHE SPEZIFIKATION
ICS 23.040.01; 93.030 Supersedes CEN/TS 14758-2:2007
English Version
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene with mineral
modifiers (PP-MD) - Part 2: Guidance for the assessment of
conformity
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Polypropylène avec Polypropylen mit mineralischen Additiven (PP-MD) -
modificateurs minéraux (PP-MD) - Partie 2 : Guide Teil 2: Empfehlungen für die Beurteilung der
pour l'évaluation de la conformité Konformität
This Technical Specification (CEN/TS) was approved by CEN on 9 June 2016 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 14758-2:2016 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Abbreviated terms . 8
5 General . 9
6 Testing and inspection . 9
6.1 Material specification . 9
6.2 Grouping . 9
6.2.1 General . 9
6.2.2 Size groups . 9
6.2.3 Fitting groups . 10
6.3 Type testing . 10
6.4 Batch release tests . 13
6.5 Process verification tests . 15
6.6 Audit tests . 16
6.7 Indirect tests . 18
6.8 Test records . 19
Annex A (informative) Basic test matrix . 20
Bibliography . 21
European foreword
This document (CEN/TS 14758-2:2016) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 14758-2:2007.
EN 14758 consists of the following parts, under the general title Plastics piping systems for non-pressure
underground drainage and sewerage — Polypropylene with mineral modifiers (PP-MD):
— Part 1: Specifications for pipes, fittings and the system
— Part 2: Guidance for the assessment of conformity (the present TS)
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Introduction
Figures 1 and 2 are intended to provide general information on the concept of testing and organization
of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type
testing (TT), batch release test (BRT), process verification test (PVT), and audit test (AT), this document
details the applicable characteristics to be assessed as well as the frequency and sampling of testing.
A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by
manufacturers is given in Figure 1.
Figure 1 — Typical scheme for the assessment of conformity by a manufacturer
A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by
manufacturers, including certification, is given in Figure 2.
Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including
certification
1 Scope
This Technical Specification gives guidance for the assessment of conformity of materials, products,
joints and assemblies in accordance with the applicable part(s) of EN 14758 intended to be included in
the manufacturer’s quality plan as part of the quality management system and for the establishment of
certification procedures.
NOTE In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 14758-1 this document is applicable to solid wall piping systems made of
polypropylene modified with mineral(s) (PP-MD) intended to be used for:
— non-pressure underground drainage and sewerage outside the building structure (application area
code “U”); and
— non-pressure underground drainage and sewerage for both buried in ground within the building
structure (application area code “D”) and outside the building structure.
This is reflected in the marking of products by “U” and “UD”.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 14758-1:2012, Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 14758-1 and the following
apply.
3.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
Note 1 to entry: A certification body is preferably compliant with EN ISO/IEC 17021-1 [1].
3.2
inspection body
body, that performs inspection
Note 1 to entry: A body can be an organization or part of an organization.
Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 [2].
3.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
Note 1 to entry: In the context of this part of EN 14758, the materials and products can be subjected to type
testing, batch release testing, process verification testing, audit testing and witness testing, as applicable.
Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 [3].
3.4
quality management system
management system to direct and control an organization with regard to quality
Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [4].
3.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.6
type testing
TT
testing performed to prove that the material, product, joint or assembly is capable of conforming to the
requirements given in the relevant standard
Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly
provided that the process verification tests are done regularly.
3.7
batch release test
BRT
test performed by or on behalf of the manufacturer on a batch of materials or products, which has to be
satisfactorily completed before the batch can be released
3.8
process verification test
PVT
test performed by or on behalf of the manufacturer on materials, products or joints at specific intervals
to confirm that the process continues to be capable of producing products which conform to the
requirements given in the relevant standard
Note 1 to entry: Such tests are not required to release batches of materials or products and are carried out as a
measure of process control.
3.9
audit test
AT
test performed by a test laboratory on behalf of an inspection body or certification body to confirm that
the material, product, joint or assembly continues to conform to the requirements given in the relevant
standard and to provide information to assess the effectiveness of the quality management system
3.10
indirect test
IT
test performed by or on behalf of the manufacturer, different from that specified test for that particular
characteristic, having previously verified its correlation with the specified test
3.11
witness test
WT
test accepted by an inspection or a certification body for type testing and/or audit testing, which is
carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or
certification body, qualified in testing
3.12
materia
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.